Commit graph

15 commits

Author SHA1 Message Date
Peng Fan
f20562e4c4 mx6: remove SYS_SOC from board Kconfig
Remove duplicated SYS_SOC Kconfig entry from board Kconfig,
because we have this entry in arch/arm/cpu/armv7/mx6/Kconfig.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2015-09-13 10:37:29 +02:00
Peng Fan
f2ff834365 imx: mx6: ddr init MMDC according to ddr_type
To i.MX6, DDR3 and LPDDR2 is supported, so rename function mx6_dram_cfg
to mx6_ddr3_cfg and the original mx6_dram_cfg function only is a wrapper.
The new reimplemented function mx6_dram_cfg only invokes mx6_ddr3_cfg
when ddr_type is for DDR3. Later we can use ddr_type to initialize
MMDC for LPDDR2.

Initialize ddr_type for different boards which enable SPL.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:34:12 +02:00
Peng Fan
6d97dc10a8 imx: clock support enet2 anatop clock support
To i.MX6SX/UL, two ethernet interfaces are supported.
Add ENET2 clock support:
1. Introduce a new input parameter "fec_id", only 0 and 1 are allowed.
   To value 1, only i.MX6SX/UL can pass the check.
2. Modify board code who use this api to follow new api prototype.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nikolaos Pasaloukos <Nikolaos.Pasaloukos@imgtec.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-09-02 15:29:14 +02:00
Fabio Estevam
dbab8b8e10 mx6cuboxi: Fix boot of hummingboard dual-lite
Hummingboard dual-lite is picking the incorrect calibration structure.

Fix it so that it can boot.

While at it, also fix p1_mpdgctrl1 register to match Solid-run's
setting.

Reported-by: Andrei Gherzan <andrei@gherzan.ro>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Andrei Gherzan <andrei@gherzan.ro>
2015-06-15 12:12:59 +02:00
Fabio Estevam
0768a69fc3 mx6cuboxi: Mention Cubox-i in the README
Cubox-i boards are also supported, so update the README file.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-05-15 19:21:23 +02:00
Fabio Estevam
a4d450380c mx6cuboxi: Pull down PAD_ENET_RXD0/RXD1
Configure PAD_ENET_RXD0/RXD1 pads as pull down because these pads are directly
connected to the Atheros 8035/8030 although they should be functional
only in the RMII mode - 8030.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
2015-05-15 19:20:47 +02:00
Fabio Estevam
712be3eef6 mx6cuboxi: Fix Ethernet PHY detection problem
mx6cuboxi sometimes fails to recognize the Ethernet PHY:

Net:   Phy 0 not found

The explanation for this behavior comes from from Rabeeh Khoury:

"The LED_ACT pin on the carrier-one boards had a pull down that
forces the phy address to 0x0; where on CuBox-i and the production
HummingBoard that pin is connected directly to LED that depending
on the pull down strength of the LED it might be sampled as '0' or '1' thus
the phy address might appear as either address 0x0 or 0x4."

"This is AR8035 implementation; in reset stage the LED pin is configured as
input, and pull up/down does matter. In this case it configures the PHY
address.

After reset is deasserted the same LED pin becomes output and then
according to the previous pull/up it should be active high/low"

One way to properly fix this behavior is to place external pull-up/down
resistors in the LED line, but from a software standpoint we can fix it
by telling phy_find_by_mask() to scan the PHY at addresses
0x0 and 0x4.

Reported-by: Vagrant Cascadian <vagrant@aikidev.net>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
2015-05-15 19:20:47 +02:00
Fabio Estevam
e1d74379ef mx6cuboxi: Add USB host support
Enable USB Host1 port.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@aikidev.net>
2015-05-15 19:20:47 +02:00
Fabio Estevam
f68a9c6b3d mx6cuboxi: Add HDMI output support
Add HDMI output using PLL5 as the source for the IPU clocks,
and accurate VESA timings.

These settings are based on the patch from Soeren Moch <smoch@web.de>
submitted for the tbs2910 mx6 based board.

It allows the display to work properly at 1024x768@60.

This should make the hdmi output signal compatible with most if not all
modern displays.

Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
2015-05-15 19:20:46 +02:00
Fabio Estevam
205d58699b mx6cuboxi: Load the correct 'fdtfile' variable
Instead of hardcoding the 'fdtfile' variable, let's detect the SoC and
board variant on the fly and change the dtb name.

Based on the scheme done on am335x board.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-27 13:13:58 +02:00
Fabio Estevam
feb6cc5cb3 mx6cuboxi: Differentiate Cubox-i and Hummingboard
Introduce is_hummingboard() function that reads GPIOs that can distinguish
between Cubox-i and Hummingboard.

Print the board name accordingly.

Based on a patch from Rabeeh Khoury.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-27 13:13:57 +02:00
Fabio Estevam
8cb6817e3a mx6cuboxi: Introduce multi-SoC support
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad. Add support for the different SoC/memory sizes
combinations.

DDR initialization values were extracted from Solid-run internal U-boot.

Tested on a CuBox-i4Pro, HummingBoard-i2eX and HummingBoard-i1.

Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-27 13:13:57 +02:00
Fabio Estevam
cfdcc5f781 mx6cuboxi: Prepare for multi SoC support
Cubox-i and Hummingboard support several MX6 SoCs: mx6solo, mx6dual-lite,
mx6dual and mx6quad.

Use IOMUX_PADS() macro in order to prepare for the multi-SoC support.
Also pass 'MX6QDL' in the defconfig to indicate it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-27 13:13:57 +02:00
Fabio Estevam
b684586a50 mx6cuboxi: Fix the defconfig name
The correct name of the defconfig file is 'mx6cuboxi_defconfig'.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-27 13:13:57 +02:00
Fabio Estevam
b8ce6fe261 mx6: Add initial SPL support for HummingBoard-i2eX
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.

For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/

Based on the work from Jon Nettleton and Rabeeh Khoury.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-04-22 14:39:06 +02:00