Since commit 61040097a9 ("reset: at91: Add reset driver for basic
assert/deassert operations") the compatible "microchip,sam9x60-rstc" for
the sam9x60 reset controller in sam9x60.dtsi is not handled by
CONFIG_SYSRESET_AT91 anymore, but by CONFIG_RESET_AT91 now. This
resulted in the following error message, when trying to reset from
U-Boot shell:
U-Boot> reset
resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###
Fixed by enabling the new driver in the relevant defconfigs. Tested on
sam9x60-curiosity board. Defconfigs for sam9x60ek adapted in the same
way, but without testing. These should be all sam9x60 boards affected
in U-Boot here.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
The board has two SD card slots and we have two defconfigs for booting
from either the first (micro SD) named 'sam9x60_curiosity_mmc_defconfig'
or the second (full size SD) named 'sam9x60_curiosity_mmc1_defconfig'.
For comparable Microchip boards (sama5d27-som1-ek, sama5d29-curiosity,
sama7g5ek) with two card slots the defconfigs only differ in BOOTARGS,
BOOTCOMMAND, and ENV_FAT_DEVICE_AND_PART and the same should be the case
for sam9x60_curiosity.
Here the 'mmc1' config has more options enabled to support the raw NAND
flash populated on the board, so the 'mmc' config (for mmc0) was adapted
by enabling additional options, instead of removing options from mmc1.
The 'mem=128M' argument can be dropped from kernel command line, because
it is redundant to memory node in dts in both Linux and U-Boot:
memory@20000000 {
reg = <0x20000000 0x8000000>;
};
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Add the configs required to use the SAM9X60's USB clock.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
[claudiu.beznea: added CONFIG_AT91_SAM9X60_USB to
sam9x60_curiosity_mmc1_defconfig]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
SAM9X60 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol. Enabling one wire and eeprom drivers
for this memory.
Signed-off-by: Durai Manickam KR <durai.manickamkr@microchip.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
