The reset value of "uSDHCx_INT_STATUS_EN" register is changed to 0
on iMX6SX. So the fsl_esdhc driver must update to set the register,
otherwise no state can be detected.
Signed-off-by: Ye.Li <B37916@freescale.com>
The User Register in GMAC IP is used to select interface type.
When with GE feature, it is used to select interface between
RGMII and GMII. If without GE feature, it is used to select
interface between MII and RMII.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.
The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
move CONFIG_SYS_SPI_WRITE_TOUT into drivers/spi/atmel_spi.h
and define a default value. Delete this define in the board
config files, where it is possible (all boards use currently
the same value).
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When boot up without mac address setting, it will give the warning
message like: "Warning: failed to set MAC address", however when
execute network related command, it still execute them without any
warning information.
With this patch, it will exit directly with following information:
"gmac0: mac address is not valid"
It also solve the problem after bootup then set mac address and the
mac address won't set to net device issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31 uses the AXP221 pmic for various voltages.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers
Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).
TODO for me:
Move the base address to device trees.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.
Also, remove unnecessary inclusion of <common.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In case of repeated START condition, the restart has to be kicked
before clear status (MSR register). If it is kicked after clear status,
R-Car I2C may transfer data (TXD register) or receive data (RXD register)
instead of transferring slave address (MAR register).
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Some slow I2C devices like Power Monitor(ZM7304) at times
do not work well with low timeout value, so I2C bus get stuck
during read cycle with this device, changing it to 100ms from
10ms works fine
A lot of other i2c drivers like mxc and i2c drivers of BOOTROM
also use relax timeouts to give sufficient ticks to work well
with slower devices
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
ppc4xx i2c master gets stuck on errors while repeated start is
active. Can be easily reproduced by "i2c md" on an unpopulated
i2c address. There is not stop condition given, scl remains
pulled low.
The only way out seems to be doing a stop manually and then a
soft reset.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Debugging some i2c trouble I saw on my scope that repeated
start is not working properply. The 4xx even held clock pulled down
after transfers. Having a look in the driver I realized
that IIC_CNTL_RPST is set on that part of the transfer that should
begin with a repeated start. But repeated start is about not sending a
stop condition, so IIC_CNTL_RPST has to be set on the last transfer
before the repeated start happens.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix error detected by cppcheck:
[drivers/net/uli526x.c:551]: (error) printf format string requires 3
parameters but only 2 are given.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Roy Zang <tie-fei.zang@freescale.com>
The pmic_spi_free function isn't ever used, and as the frameworks stand
today, cannot be, so remove it. Integrate the probe function into
pmic_reg as it's not really a "probe" today. Finally, add an err label
for the common failure cases.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Make sure to keep the MAC address programmed in the SMC911x ADDRH
and ADDRL registers. Linux can read those registers to determine
the MAC address on EEPROM-less configurations.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Tom Rini <trini@ti.com>
CMD_IAAD (Interrupt on Async Advance Doorbell) is bit 6, not bit 5.
While we are here, sort the flags.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Split the Samsung specific PHY control into a separate file
and compile this into the S3C OTG driver only if used on a
Samsung system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Encapsulate the Samsung PHY control and its register accesses
into the otg_phy_init() and otg_phy_off() functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Remove the useless inclusion of arch/arm/gpio.h , which is completely
bogus in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The verification qm_cfg existence is done at ksnav_init().
So, there is no need to verify it after initialization.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514
Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires
that certain registers get written in order to restart
autonegotiation.
Signed-off-by: Hao Zhang <hzhang@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Keystone2 Lamar SoC uses the same keystone net driver.
This patch adds opportunity to use it by K2L SoCs.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Keystone2 Lamar SoC uses the same keystone SerDes driver.
All Keystone2 EVM boards currently use SerDes driver, so move
CONFIG_TI_KEYSTONE_SERDES to common configuration file.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is necessary for the device-model enabled builds to work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds driver model support to the sunxi GPIO driver, using the device
tree to trigger binding of the driver. The driver will still operate
without driver model too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
