Currently CONFIG_BOARD_SIZE_LIMIT check is ignored for u-boot-spl.kwb
target. Fix it by adding missing $(BOARD_SIZE_CHECK) macro.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Use 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && CONFIG_OF_SEPARATE' pattern
instead of 'CONFIG_MPC85XX_HAVE_RESET_VECTOR && !CONFIG_OF_EMBED' also in
OBJCOPYFLAGS_u-boot-nodtb.bin as this pattern is used in rest of Makefile.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Building of final u-boot.bin binary for mpc85xx via binman is needed only
when inserting DTB binary in the middle of the u-boot ELF binary (before
.bootpg and .resetvec ELF sections).
These requirements are met when CONFIG_MPC85XX_HAVE_RESET_VECTOR is enabled
(= generating .bootpg/.resetvec sections) and CONFIG_OF_SEPARATE is enabled
(= inserting DTB binary).
So in all other cases use standard build procedure instead of custom
mpc85xx u-boot.bin Makefile target via binman.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Currently Makefile produces final mpc85xx image when SPL is not used in
custom file u-boot-with-dtb.bin. It is quite confusing name as build
process produce also intermediate file standard file u-boot-dtb.bin (which
is just intermediate and not bootable). Other platforms use u-boot.bin
(UBOOT_BIN) as standard name for final bootable raw image.
So change Makefile rules and binman to produce final bootable file for
mpc85xx also into file u-boot.bin. There is just need for mpc85xx to not
define default rule for u-boot.bin then instruct binman (via DTS file) to
store final image into u-boot.bin (instead of u-boot-with-dtb.bin) and
finally rename target u-boot-with-dtb.bin to u-boot.bin.
With this change are also removed custom Makefile hacks for mpc85xx that it
produced non-standard output file. And also updated documentation.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Makefile uses binman to produce u-boot-with-dtb.bin target. As its input it
takes DTB file and u-boot binary without DTB, which is stored in file
u-boot-nodtb.bin. So fix target dependency.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Running tests in parallel is much faster, e.g. 15 seconds to run the tests
on sandbox (only), instead of 100 seconds (on a 16-core machine). Add a
'make pcheck' option to access this feature.
Note that the tools/ tests still run each tool's tests once after the
other, although within that, they do run in parallel. So for example,
the buildman tests run in parallel, then the binman tests run in
parallel. There would be a signiificant advantage to running them all
in parallel together, but that would require a large amount of
refactoring, e.g. with more use of pytest fixtures.
Update the documentation to represent the current state.
Signed-off-by: Simon Glass <sjg@chromium.org>
This new image is similar to u-boot-rockchip.bin except that it's
destined to be flashed on SPI-NOR flashes.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By factoring SPL check in the first condition, this makes the checks a
bit less convoluted and more readable.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows to build u-boot-rockchip.bin binary with binman for Rockchip
ARM64 boards instead of the legacy Makefile way.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
idbloader.img content - currently created by way of Makefile - can be
created by binman directly.
So let's do that for Rockchip ARM platforms.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Binman mkimage entry generates temporary files so let's remove them
when calling `make clean`.
Fixes: 9b312e26fc ("rockchip: Enable building a SPI ROM image on jerry")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reported-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
LTO (Link-Time Optimisation) is an very useful feature which can
significantly reduce the size of U-Boot binaries. So far it has been
made available for selected ARM boards and sandbox.
However, incremental builds are much slower when LTO is used. For example,
an incremental build of sandbox takes 2.1 seconds on my machine, but 6.7
seconds with LTO enabled.
Add a NO_LTO parameter to the build, similar to NO_SDL, so it can be
disabled during development if needed, for faster builds.
Add some documentation about LTO while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The deadline for DM_ETH migration passed 2 years ago. Now that
platforms which cannot be migrated have been either removed or had
drivers disabled, and platforms that needed minor help to migrate have
been forcefully migrated, we can complete the migration.
This entails select'ing DM_ETH under NETDEVICES, and then removing now
extraneous depends on lines. In a few places, we can now either remove
options or just simplify later dependencies.
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
When compiling with -Og gcc reports false positive -Wmaybe-uninitialized as
reported in https://gcc.gnu.org/bugzilla/show_bug.cgi?id=78394.
Silence these warnings when building with CONFIG_CC_OPTIMIZE_FOR_DEBUG.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ISP1760/61/63 are a family of usb controllers, here the main
goal is to support the ISP1763 hcd part found in the MPS3 FPGA
board form Arm. This is based on the kernel driver and ported
to u-boot.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
If CONFIG_CC_OPTIMIZE_FOR_DEBUG=y, the host tools should be built with
debug symbols and with reduced optimization.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When running "make clean" we want to remove env.in and well as env.txt.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
There is no need to pass section information via parameters.
Let's read text base and rela start/end directly from elf.
It will help with reading other information from ELF for others
architecture. Input to relocate-rela is u-boot binary and u-boot ELF.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ab7ae14a6e058722e8c608089729e98edf20a08d.1655299267.git.michal.simek@amd.com
mpc85xx NOR binary contains also reset vector and therefore option
CONFIG_MPC85XX_HAVE_RESET_VECTOR must be defined.
When build system uses binman, it takes care of constructing final image
which consist of u-boot-without-reset-vector, DTB and reset-vector.
CONFIG_OF_EMBED does not use binman, there is no external DTB and Makefile
produce directly final u-boot.bin binary.
So in this case mpc85xx reset vector must not be stripped from the final
u-boot.bin binary. Fix it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Update the diagnostic message with revised location of document, which
changed in 3e9fddfc4f ("doc: Move devicetree control doc to rST")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Use [:space:] instead of \s and \S in regular expression that
determines the sandbox target architecture. Fixes the build
failure on OpenBSD introduced with commit 4e65ca00f3
("efi_loader: bootmgr: add booting from removable media").
Fixes: f7691a6d73 ("sandbox: allow cross-compiling sandbox")
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current logic checks several options to decide whether SPL/TPL need
the U-Boot devicetree to be built. In fact we can check OF_CONTROL, which
is enabled in all cases that matter.
Signed-off-by: Simon Glass <sjg@chromium.org>
This will sort the default environment file generated by
"make u-boot-initial-env", but won't sort the default
environment in the compiled u-boot binary. The file
u-boot-initial-env is considered to use for the userpace
environment access tools [1] in case of that the
environments is written the first time into its location.
This is done on the one hand for a better overview and
comparison of the generated environment file. On the other
hand it is to synchronize the output with the script
get_default_env.sh, which generated a sorted default
environment file. The sorting preserves the order of equal
variable names by sorting only the variable name, and
disable the last-resort comparison. After sorting,
unnoticed blank lines at the end move to the top. Avoid
that by removing it before sorting.
[1] https://github.com/sbabic/libubootenv
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Behún <marek.behun@nic.cz>
To: u-boot@lists.denx.de
Reviewed-by: Simon Glass <sjg@chromium.org>
fix compile error when using a little-endian to build with configs:
sfr_nb4-ser_ram_defconfig
comtrend_wap5813n_ram_defconfig
comtrend_ar5387un_ram_defconfig
comtrend_ct5361_ram_defconfig
comtrend_vr3032u_ram_defconfig
comtrend_ar5315u_ram_defconfig
huawei_hg556a_ram_defconfig
netgear_dgnd3700v2_ram_defconfig
Signed-off-by: Du Huanpeng <dhu@hodcarrier.org>
If include/generated/env.in does not exist, which is a typical case for
clean build, quiet_cmd_gen_envp command tries to delete this file
unconditionally.
This produces following warning during the build:
ENVP include/generated/env.in
rm: cannot remove 'include/generated/env.in': No such file or directory
Add '-f' option to the `rm` command to not complain if file does not
exist.
Fixes: f432eb6d8a ("env: Avoid using a leftover text-environment file")
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
If include/generated/environment.h exists (perhaps leftover from a build
of another board) it is used, even if the board currently being built does
not have a text environment.
This causes a build error. Fix it by emptying the file if it should not be
there.
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/9
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Sean Anderson <seanga2@gmail.com>
Set the variable pre-load-key-path with the shell variable
PRE_LOAD_KEY_PATH that contain the keys path (used for signature).
This variable pre-load-key-path is provided to binman.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
