Commit graph

21 commits

Author SHA1 Message Date
Stefan Wahren
7bbc5ff732 mxs: Do not disable bo detection when DC-DC is already enabled
In case the DC-DC is already enabled mxs_enable_4p2_dcdc_input() returns
without reenabling brown out detection. So fix this issue by
moving the return before brown out deactivation.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2015-06-01 09:21:54 +02:00
Graeme Russ
7a08603707 arm: mxs: Enable booting of mx28 without battery
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.

This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
 - Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
 - Switch between 4P2 Linear Regulator and Battery, using whichever has
   the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
   the same as the pre-patch behaviour)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
2015-02-10 12:48:50 +01:00
Graeme Russ
950eaf6230 arm: mxs: Add debug outputs and comments to mxs SPL source files
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
 - Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
 - Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:49 +01:00
Masahiro Yamada
4515992fc7 replace DIV_ROUND with DIV_ROUND_CLOSEST
The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible
and safer than DIV_ROUND.

For example,
  foo = DIV_ROUND_CLOSEST(x, y++)
works expectedly, but
  foo = DIV_ROUND(x, y++)
does not. (y is incremented twice.)

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Marek Vasut
a0f9761075 ARM: mxs: Enable DCDC converter for battery boot
In case the board detected sufficient voltage for battery boot,
make sure the DCDC converter is ON and the board is not running
only from linregs, otherwise an instability will be observed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-31 17:54:23 +01:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Marek Vasut
d4c9135c96 ARM: mxs: Document the power block initialization
This patch adds documentation for the functions used during the
initialization of MXS power block.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Hector Palacios
6f6059e0f1 ARM: mxs: rename function that sets AUTO_RESTART flag
The AUTO_RESTART flag of HW_RTC_PERSISTENT0 register will
power up the chip automatically 180ms after power down.
This bit must be enabled by the boot loader to ensure the
target can start upon hardware reset or watchdog reset
even when powered from a battery.

Currently the function named 'mxs_power_clear_auto_restart()'
is setting this flag although the 'clear' in its name suggest
the opposite.

This patch renames the function to 'mxs_power_set_auto_restart()'
and removes the comment about EVK revision A which was confusing
because the function indeed was setting the flag.

Signed-off-by: Hector Palacios <hector.palacios@digi.com>
2013-08-31 17:50:38 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Marek Vasut
dd3ecf020e arm: mx23: Fix VDDMEM misconfiguration
The VDDMEM ramped up in very weird way as it was horribly misconfigured.
Instead of setting up VDDMEM in one swipe, let it rise slowly the same
way as VDDD and VDDA in spl_power_init.c and then only clear ILIMIT before
memory gets inited. This makes sure the VDDMEM rises sanely, not jumps up
and down as it did till now.

The VDDMEM prior to this change did this:
     2V0____   .--------2V5
       |    `--'
 0V____|

The VDDMEM now does this:
    2V0_____,-----------2V5
      /
 0V__|

Moreover, VDDIO on MX23 uses 25mV steps while MX28 uses 50mV steps,
fix this difference too.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-05-06 10:20:33 +02:00
Otavio Salvador
a74dbf2734 mxs: Rename CONFIG_SPL_MX28_PSWITCH_WAIT to CONFIG_SPL_MXS_PSWITCH_WAIT
The power switch option is compatible with i.MX23 and i.MX28 so the
configration option needs to reflect it. We choose
'CONFIG_SPL_MXS_PSWITCH_WAIT' for the option name.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
2013-03-07 17:22:57 +01:00
Marek Vasut
7788bf067d mxs: Add function to ungate the power block on MX23
The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:22 +01:00
Marek Vasut
a918a53c36 mxs: Staticize SPL functions
The MXS SPL didn't mark local functions "static". Fix it. This also makes the
SPL smaller by roughly 300 bytes.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04 09:29:11 +01:00
Marek Vasut
1230e7bc2d mxs: Properly setup VDDD in power supply setup code
The memory setup code adjusted the VDDD voltage. Remove this adjustment
and configure the VDDD voltage correctly in the power supply setup code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04 09:27:21 +01:00
Marek Vasut
77cb33bd25 mxs: Implement common function to setup VDDx
Implement common function to setup the VDDIO, VDDD and VDDA voltage.
Right now, there are two almost identical functions to setup VDDIO
and VDDD, which is prone to breakage. Pull out the differences into
constant structure and pass them as an argument to the common function.

Moreover, the function has almost identical loops for setting higher
and lower VDDx voltage. Merge these two loops.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04 09:26:54 +01:00
Marek Vasut
fdb00b8127 MX28: Shuffle around the power management code
Move some function calls to a more appropriate place, so they're
called only when needed.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:25 +02:00
Stathis Voukelatos
8b165a5394 i.MX28: bug fixes in PMU configuration code
Signed-off-by: Stathis Voukelatos <stathis.voukelatos@linn.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
2012-09-01 14:58:18 +02:00
Otavio Salvador
05c823bd32 mxs: Clarify why we poweroff in case of brownout in 5v conflict
If VDDIO has a brownout, then the VDD5V_GT_VDDIO becomes unreliable
but this wasn't clear on code so a comment has been added to clarify
it.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Otavio Salvador
1e0cf5c34b mxs: Reowork SPL to use 'mxs' prefix for methods
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Otavio Salvador
9c471142bc mxs: prefix register structs with 'mxs' prefix
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Otavio Salvador
3a0398d7b9 mxs: reorganize source directory for easy sharing of code in i.MXS SoCs
Most code can be shared between i.MX23 and i.MX28 as both are from
i.MXS family; this source directory structure makes easy to share code
among them.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:17 +02:00
Renamed from arch/arm/cpu/arm926ejs/mx28/spl_power_init.c (Browse further)