Armada 385 contains 64 lines of HD eFuse and 2 lines of LD eFuse. HD eFuse
is used for secure boot and each line is 64 bits long + 1 lock bit. LD
eFuse lines are 256 bits long + 1 lock bit. LD 0 line is reserved for
Marvell Internal Use and LD 1 line is for General Purpose Data. U-Boot
already contains HD eFuse reading and programming support.
This patch implements LD eFuse reading support. LD 0 line is mapped to
U-Boot fuse bank 64 and LD 1 line to fuse bank 65.
LD 0 Marvell Internal Use line seems that was burned in factory with some
data and can be read by U-Boot fuse command:
=> fuse read 64 0 9
LD 1 General Purpose Data line is by default empty and can be read by
U-Boot fuse command:
=> fuse read 65 0 9
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
uDPU is a bit of a specific device in that it does not have any copper
ports nor any ethernet PHY-s but 2 SFP ports.
This is an issue since MVNETA requires a PHY phandle or a fixed-link to
be defined under its node.
Since U-boot has no SFP support this is reasonable in order to know how
to configure the MAC.
However this also means that networking does not work on uDPU at all
currently, and fails with:
uDPU>> dhcp
Could not get PHY for neta@30000: addr 0
phy_connect failed
Could not get PHY for neta@40000: addr 1
phy_connect failed
So, to provide working networking using only SFP-s let add the fixed-link
at 1G which is much more common than 2.5G SFP-s as well as disable the
TX_DISABLE pins like done on Armada 7040 and 8040 platforms.
Since uDPU is not using any of the GPIO-s on the SB controller for any
purpose other than GPIO, a call to the pinctrl must be made in order for
it to get probed and thus register the SB GPIO bank, otherwise SB GPIO-s
are not registered at all.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
It is not possible for the A53 core (on which U-Boot is running) to read it
directly. For this purpose Marvell defined mbox API for sending OTP
commands between CM3 and A53 cores.
Implement these Marvell fuse reading mbox commands via U-Boot fuse API.
Banks 0-43 are used for accessing Security OTP (44 rows with 67 bits via 44
banks and words 0-2).
Note that of the 67 bits, the 3 upper bits are: 1 lock bit and 2
auxiliary bits (meant for testing during the manufacture of the SOC, as
I understand it).
Also note that the lock bit and the auxiliary bits are not readable
via Marvell commands.
With CZ.NIC's commands the lock bit is readable.
Write support is not implemented yet.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement reading NB and SB fuses of Armada 37xx SOC via U-Boot fuse API.
Banks 0-43 are reserved for accessing Security OTP (not implemented yet).
Bank 44 is used for accessing North Bridge OTP (69 bits via words 0-2).
Bank 45 is used for accessing South Bridge OTP (97 bits via words 0-3).
Write support is not implemented yet because it looks like that both North
and South Bridge OTPs are already burned in factory with some data. The
meaning of some bits of North Bridge is documented in WTMI source code.
The meaning of bits in South Bridge is unknown.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
The DT node name pattern in mmc-controller.yaml for mmc
is "^mmc(@.*)?$". The Rockchip mmc nodes have been synced
with Linux, so update the boot_devices constants as well.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to sync rk3288.dtsi from Linux it needed to
move all u-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3288
sync the power domain dt-binding header.
This is the state as of v5.17 in Linux.
Change location to be more in line with other SoCs.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to sync rk322x.dtsi from Linux, move all
U-boot specific properties in separate dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM. Add rk3066a-mk808.dts. Move U-boot specific
things in a rk3066a-mk808-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Add rk3066a.dtsi. Move U-boot specific
things in a rk3066a-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move the include for rk3xxx-u-boot.dtsi to rk3188-u-boot.dtsi
to stay in line with U-boot dtsi files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The file rk3xxx-u-boot.dtsi was original only for rk3188 and SPL.
With rk3066 added some nodes are also needed in TPL,
so change them to u-boot,dm-pre-reloc
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the clock driver for the rk3066 platform.
Derived from the rk3288 and rk3188 driver it
supports only a bare minimum to bring up the system
to reduce the TPL size for:
SDRAM clock configuration.
The boot devices NAND, EMMC, SDMMC, SPI.
A UART for the debug messages (fixed) at 115200n8.
A SARADC for the recovery button.
A TIMER for the delays (fixed).
There's support for two possible frequencies,
the safe 600MHz which will work with default pmic settings and
will be set to get away from the 24MHz default and
the maximum of 1.416Ghz, which boards can set if they
were able to get pmic support for it.
After the clock tree is set during the TPL probe
there's no parent update support.
In OF_REAL mode the drivers ns16550.c and dw-apb-timer.c
obtain the (fixed) clk_get_rate from the clock driver
instead of platdata.
The rk3066 cru node has a number of assigned-clocks properties
that call the .set_rate() function. Add them to the list so that
they return a 0 instead of -ENOENT.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
grf is needed by various drivers for rk3066 soc.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Not all Rockchip SoC models use the ARM arch timer.
Call the function timer_init() only when
CONFIG_SYS_ARCH_TIMER is available.
Use the call condition IS_ENABLED to increase
build coverage and make the code easier to read.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE
defined. Currently there's no exception in TPL. Make this more
generic and compile the code inside the function rockchip_stimer_init()
only when CONFIG_ROCKCHIP_STIMER_BASE is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip SoCs rk3066/rk3188 have no CONFIG_ROCKCHIP_STIMER_BASE
defined. Currently only rk3188 has an exception in SPL. Make this more
generic and compile code inside the function rockchip_stimer_init()
only when CONFIG_ROCKCHIP_STIMER_BASE is available.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The M1 Ultra consists of two M1 Max dies. The second die's I/O is at
a consistent offset of 0x2000000000.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.
By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
=> smc 0xc2000003 0 0 0 0 0 0
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable instruction cache early on to speed up the boot process on i.MX8M.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Linux kernel moved dt-bindings/pinctrl/pins-imxrt to the device tree
This patch move it in U-Boot as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
In Linux IMX and IMXRT use the device tree to hold the anatop address.
The anatop is used in clock drivers as it controls the internal PLLs
This will move the macro from asm/arch-imxrt to the device tree.
This presumably should also be done with the other IMX boards as well.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.
The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The GW7902-C revision adds an ADC for the VDD_5P0 voltage rail.
Add register definitions for it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This macro currently supports only one parameter. Based on Linux iopoll,
let's extend read_poll_timeout common API to allow multiple variable
parameters.
Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Add init_nand_clk to enable gpmi nand clock. Since i.MX8M not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Turns out on certain carrier boards (e.g. Iris V2) and under certain
circumstances (e.g. after a software reset) the SD card may have been
left in a strange state which later failed as follows:
Colibri iMX6ULL # mmc dev 0
Card did not respond to voltage select! : -110
Fix this as follows:
- Re-name the signaling voltage rail regulator from vmmc to vqmmc.
- Fix the name of the GPIO property to gpios.
- Specify 4-bit bus width, no write-protect capability and no 1.8
volt signaling voltage capability.
- Fix the clock vs. command pull-up vs. push-pull configuration.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Explicitly use the atf-bl31 type for the bl31.bin atf-blob. This uses
the path from the BL31 environment variable, if defined.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.
If provide both, kernel would failed to request the same gpio twice
and cause fec not work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
