Commit graph

46074 commits

Author SHA1 Message Date
Stephen Warren
6dbcc962e4 ARM: tegra: add peripheral clock init table
Currently, Tegra peripheral drivers control two aspects of their HW module
clock(s):

1) The clock enable/rate for the peripheral clock itself.

2) The system-level clock tree setup, i.e. the clock parent.

Aspect 1 is reasonable, but aspect 2 is a system-level decision, not
something that an individual peripheral driver should in general know
about or influence. Such system-level knowledge ties the driver to a
specific SoC implementation, even when they use generic APIs for clock
manipulation, since they must have SoC-specific knowledge such as parent
clock IDs. Limited exceptions exist, such as where peripheral HW is
expected to dynamically switch between clock sources at run-time, such
as CPU clock scaling or display clock conflict management in a multi-head
scenario.

This patch enhances the Tegra core code to perform system-level clock
tree setup, in a similar fashion to the Linux kernel Tegra clock driver.
This will allow future patches to simplify peripheral drivers by removing
the clock parent setup logic.

This change is required prior to converting peripheral drivers to use the
standard clock APIs, since:

1) The clock uclass doesn't currently support a set_parent() operation.
Adding one is possible, but not necessary at the moment.

2) The clock APIs retrieve all clock IDs from device tree, and the DT
bindings for almost all peripherals only includes information about the
relevant peripheral clocks, and not any potential parent clocks.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
ee562dc34e ARM: tegra: pull Tegra210 SoC DT from Linux v4.7
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.

Main changes:
* Brought in the correct Tegra210 CAR binding; the old file in U-Boot
  appears to be a renamed version of the Tegra124 bindings rather than
  the real Tegra210 version.
* Conversion of SPI and UART nodes to standard DMA bindings. U-Boot
  doesn't use DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
  information required by U-Boot, so U-Boot is not affected.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot, including separation of the
  Tegra LIC (Legacy IRQ controller) and GIC.
* Node sort order fixes.

Remaining deltas relative to the Linux DT:
* U-Boot has enabled PCIe for Tegra210, but the kernel hasn't yet.
* The GPIO node compatible value in the kernel explicitly includes
  Tegra124 values whereas U-Boot does not. I'll send a kernel patch to
  correct this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
3b8c1b3b22 ARM: tegra: pull Tegra124 SoC DT from Linux v4.7
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.

Main changes:
* USB phy_type property is aligned with the kernel, so board files are
  updated so the final DT content doesn't change. I'm not convinved that
  Nyan uses HSIC phy_type. However, I'd rather this change be a no-op,
  and any DT bug-fixes be separate.
* Sync misc changes from the kernel: missing DT content, minor compatible
  value fixes, typos.

Remaining deltas relative to the Linux DT:
* U-Boot uses #address-cells/#size-cells of 1 whereas the kernel uses 2.
  I believe U-Boot's DT parsing currently assumes that these values match
  the physical address size, so I didn't synchronize this part of the DT.
* U-Boot uses the original XUSB PHY DT binding, wherease the kernel DT
  has moved to a newer version. Thus, XUSB client nodes include properties
  names phys and phy-names that do not appear in the kernel, and don't
  include pad definitions in the padctl node.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
5c31e7abb4 ARM: tegra: pull Tegra114 SoC DT from Linux v4.7
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.

Main changes:
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
  DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
  information required by U-Boot, so U-Boot is not affected.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra114-mc.h since tegra114.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.

Remaining deltas relative to the Linux DT:
* USB node compatible values in U-Boot explicitly list Tegra114 values
  whereas the kernel does not. I'll send a kernel patch to correct this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
ce2f2d2ae7 ARM: tegra: pull Tegra30 SoC DT from Linux v4.7
The primary benefit of this change is that it adds all missing clocks and
resets properties to peripherals. This will allow peripheral drivers to
migrate to the standard clock and reset APIs in the future.

Main changes:
* Modification of PCIe memory region addresses. The HW memory layout is
  programmable, so this should work fine, and Beaver PCIe was tested
  without issue.
* Removal of pcie_xclk from the PCIe node and clock binding header. This
  clock doesn't exist and isn't used; only a reset with this ID exists.
* Conversion of SPI nodes to standard DMA bindings. U-Boot doesn't use
  DMA so isn't affected.
* Split of EHCI and USB PHY nodes. The EHCI nodes continue to contain all
  information required by U-Boot, so U-Boot is not affected.
* Changed the phy_type value for the second USB port. This required board
  DTs to be updated to keep the same configuration.
* Boards need to define the clk32k_in clock that feeds the Tegra PMC.
* Addition of tegra30-mc.h since tegra30.dtsi now includes it.
* Conversion of many magic numbers to named defines.
* Addition of many nodes not used by U-Boot.
* Node sort order fixes.

Remaining deltas relative to the Linux DT:
* None.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
50a303bdfa ARM: tegra: pull Tegra20 SoC DT from Linux v4.7
This brings in a few minor fixes since the last sync. The largest change
is the removal of the definition for TEGRA20_CLK_PCIE_XCLK. This clock
doesn't actually exist.

Remaining deltas:
* Addition of u-boot,dm-pre-reloc property to a couple of nodes.
* Addition of the NAND controller, which Linux doesn't yet support.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:02 -07:00
Stephen Warren
eb631d7fb0 ARM: tegra: remove "0, " from DT unit addresses
Apparently the unit address in a DT node name is now supposed to be a
single integer value, rather than a comma-separated list of individual
cell values. Fix the U-Boot DTs to comply with this naming convention.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Tom Warren
6a474db489 mmc: tegra: Add DM_MMC support to Tegra MMC driver
Convert the Tegra MMC driver to DM_MMC. Support for non-DM is removed
to avoid ifdefs in the code. DM_MMC is now enabled for all Tegra builds.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
(swarren, fixed some NULL pointer dereferences, removed extraneous
changes, rebased on various other changes, removed non-DM support etc.)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Stephen Warren
c0be77dbdb ARM: tegra: set MMC pin mux in board_init()
Most other pin mux is configured in this function. This removes the
need to do it in an MMC-specific initialization function, which is good
since that function is going away later in this series.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Stephen Warren
f53c4e4bbd mmc: tegra: priv struct and naming cleanup
struct mmc_host is a Tegra-specific structure, but the name implies it's
something defined by core MMC code, which is confusing. Rename it to
struct tegra_mmc_priv to make its purpose more obvious. The new name is
also more appropriate for a DM driver private data structure, which will
be relevant later in this series.

Nothing needs access to this type except the MMC driver itself. Move the
definition into the driver C file.

Make sure all Tegra MMC functions are named tegra_mmc_*. Even though
they're all static, it's useful to have good naming so that symbol tables
are easy to interpret. A few functions aren't renamed by this patch since
they'll be deleted by a subsequent patch in this series.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Stephen Warren
6138d5b682 mmc: tegra: don't use periph_id in pad_init_mmc()
The MMC driver will soon be converted to use standard clock/reset APIs,
and so the periph_id field in the MMC device priv struct will disappear.
Rework the implementation of pad_init_mmc() to rely on this; using the
device register address is a much more direct test anyway.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Stephen Warren
6b83588eea mmc: tegra: move pad_init_mmc() into MMC driver
pad_init_mmc() is performing an SoC-specific operation, using registers
within the MMC controller. There's no reason to implement this code
outside the MMC driver, so move it inside the driver.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Stephen Warren
67748a73b1 mmc: tegra: use correct alias for SDHCI/MMC nodes
The Tegra MMC driver currently honors "sdhci" entries in /aliases. The
MMC core however uses "mmc" entries in /aliases. This difference will be
relevant once the Tegra MMC driver is converted to DM, and the MMC core
handles alias lookups. To avoid issues during that conversion, fix the
Tegra MMC driver and all Tegra DTs to use the same alias name as the MMC
core does.

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Tom Warren
9a06a1a3a1 ARM: tegra: fdt: Add 'non-removable' property to all eMMC nodes
During debug of the DM_MMC changes to the Tegra MMC driver, I
noticed that the 'removable' property wasn't being set correctly
for the eMMC parts on most Tegra boards. Since the kernel DTS has
this property set correctly, it should be in U-Boot's Tegra DT too.

Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-09-27 09:11:01 -07:00
Bryan Wu
64a4fe7401 ARM: tegra: increase console buffer size and sys args num
The Linux-for-Tegra kernel uses a very long command line.

The default value of CONFIG_SYS_CBSIZE is too small to printf out the
long command line and causes a message like:
  bootarg overflow 602+0+0+1 > 512
on the console, and the board refuses to boot.

The default value of CONFIG_SYS_MAXARGS is too small to add a long
long command line, and the kernel won't boot without the complete
bootargs.

Increasing these two config options solves this problem.

Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Peter Chubb <Peter.Chubb@data61.csiro.au>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-09-27 09:11:01 -07:00
Tom Rini
6d5565608f Merge git://www.denx.de/git/u-boot-marvell 2016-09-27 11:40:56 -04:00
Stefan Roese
b28d29f784 arm64: mvebu: armada-7040-db.dts: Add I2C and SPI aliases
Add I2C and SPI aliases to enable usage in U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
788068912f arm64: mvebu: Armada 7K/8K: Add COMPHY device tree nodes
This patch adds the COMPHY device tree nodes that are still missing to
the Armada 7K/8K dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
b5fbf5aabe arm64: mvebu: armada-ap806.dtsi: Add clock-frequency to UART DT node
The clock frequency needs to be provided in the DT. Otherwise the driver
won't start in U-Boot.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
6f8c2d4906 arm64: mvebu: Add Armada 7K db-88f7040 development board support
This patch adds basic support for the Marvell Armada 7K DB-88F7040
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- USB
- SATA / AHCI

Support for other interfaces will follow.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
21b29fc64e arm64: mvebu: Add basic support for the Marvell Armada 7K/8K SoC
Compared to the Armada 3700, the Armada 7K and 8K are much more on the
high-end side: they use a dual Cortex-A72 or a quad Cortex-A72, as
opposed to the Cortex-A53 for the Armada 3700.

The Armada 7K and 8K also use a fairly unique architecture, internally
they are composed of several components:

- One AP (Application Processor), which contains the processor itself
  and a few core hardware blocks. The AP used in the Armada 7K and 8K
  is called AP806, and is available in two configurations:
  dual Cortex-A72 and quad Cortex-A72.
- One or two CP (Communication Processor), which contain most of the I/O
  interfaces (SATA, PCIe, Ethernet, etc.). The 7K family chips have one
  CP, while the 8K family chips integrate two CPs, providing two times
  the number of I/O interfaces available in the CP.
  The CP used in the 7K and 8K is called CP110.

All in all, this gives the following combinations:

- Armada 7020, which is a dual Cortex-A72 with one CP
- Armada 7040, which is a quad Cortex-A72 with one CP
- Armada 8020, which is a dual Cortex-A72 with two CPs
- Armada 8040, which is a quad Cortex-A72 with two CPs

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support,
starting with the Marvell DB-88F7040 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
1335483a69 arm64: mvebu: Armada 7K/8K: Add Armada 7K/8K dts files
This patch integrates the Armada 7K/8K dts files from the latest
submission on the linux-arm-kernel mailing list.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
22f5de6b5c ahci: Make ahci_port_base() non-static to enable overwrite
To allow a board- / platform-specific ahci_port_base() function, this
patch removes "static inline" and adds __weak to this function. This
will be used by the upcoming Armada 7K/8K SATA / AHCI support, which
unfortunately needs a different port base address calculation.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
d36277ef4f usb: xhci-mvebu: Add Armada 8K to compatiblity list
To enable this driver on Armada 7K/8K this patch adds the compatibility
property to the list.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
c0132f6005 drivers/phy: Add Marvell SerDes / PHY drivers used on Armada 7K/8K
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:

Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
2016-09-27 17:29:54 +02:00
Stefan Roese
01e62c7f11 arm64: mvebu: Add Armada 3700 db-88f3720 development board support
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
f61aefc150 arm64: mvebu: Add support for the Marvell Armada 3700 SoC
The Armada 3700 integrates the following interfaces (not complete list):
- Dual Cortex-A53 ARMv8
- USB 3.0
- SATA 3.0
- PCIe 2.0
- 2 x Gigabit Ethernet 1Gbps / 2.5Gbps
- ...

This patch adds basic support for this ARMv8 based SoC into U-Boot.
Future patches will integrate other device drivers and board support
for the Marvell DB-88F3720 development board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
f733228ade arm64: mvebu: Armada 3700: Add USB device tree nodes
This patch adds the USB device tree nodes that are still missing to
the Armada 3700 dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
56d5395697 arm64: mvebu: Armada 3700: Add COMPHY device tree nodes
This patch adds the COMPHY device tree nodes that are still missing to
the Armada 3700 dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
9e9e63c027 arm64: mvebu: Armada 3700: Add I2C device tree nodes
This patch adds the I2C device tree nodes that are still missing to
the Armada 3700 dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
3f84e2e890 arm64: mvebu: Armada 3700: Add ethernet device tree nodes
This patch adds the ethernet device tree nodes that are still missing to
the Armada 3700 dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
cdccf9c17b arm64: mvebu: Armada 3700: Add SPI device tree nodes
This patch adds the SPI device tree nodes that are still missing to
the Armada 3700 dts files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
850db82fcb arm64: mvebu: Armada 3700: Add Armada 37xx dts files
This patch integrates the Armada 3700 dts files from the latest
submission on the linux-arm-kernel mailing list.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
3335786a98 drivers/phy: Add Marvell SerDes / PHY drivers used on Armada 3k
This version is based on the Marvell U-Boot version with this patch
applied as latest patch:

Git ID 7f408573: "fix: comphy: cp110: add comphy initialization for usb
device mode" from 2016-07-05.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:53 +02:00
Stefan Roese
c6cfcc91ea usb: ehci: ehci-marvell.c: Add Armada 3700 support (ARMv8)
This patch adds DM based support for the Armada 3700 EHCI controller.
The address windows don't need to get configured in this case. The
difference here is detected via DT compatible property at runtime.

With this support and the DM xHCI driver, both XHCI and eHCI can be
used simultaniously on the MVEBU boards now.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
2016-09-27 17:29:53 +02:00
Stefan Roese
81c1f6f0c3 usb: xhci: Add Marvell MVEBU xHCI support
This patch adds DM based support for the xHCI USB 3.0 controller
integrated in the Armada 3700 SoC. It may be extended to be used
by other MVEBU SoCs as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
2016-09-27 17:29:52 +02:00
Stefan Roese
544eefe084 net: mvneta: Add support for Armada 3700 SoC
This patch adds support for the Armada 3700 SoC to the Marvell mvneta
network driver.

Not like A380, in Armada3700, there are two layers of decode windows for GBE:
First layer is:  GbE Address window that resides inside the GBE unit,
Second layer is: Fabric address window which is located in the NIC400
                 (South Fabric).
To simplify the address decode configuration for Armada3700, we bypass the
first layer of GBE decode window by setting the first window to 4GB.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
3cbc11da86 net: mvneta: Make driver 64bit safe
The mvneta driver is also used on the ARMv8 64bit Armada 3700 SoC. This
patch fixes the compilation warnings seen on this 64bit platform.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
3fda4ef395 spi: Add driver for Marvell Armada 3700 SoC
The SPI IP core in the Marvell Armada 3700 is similar to the one in the
other Armada SoCs. But the differences are big enough that it makes
sense to introduce a new driver instead of cluttering the old
kirkwood driver with #ifdef's.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
6985d49662 serial: Add serial_mvebu_a3700 for Armada 3700 SoC
The Armada 3700's UART is a simple serial port. It has a 32 bytes
Tx FIFO and a 64 bytes Rx FIFO integrated. This patch adds support
for this UART including the DEBUG UART functions for very early
debug output.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
2016-09-27 17:29:52 +02:00
Stefan Roese
35e3fca7e3 net: mvneta: Round up top tx buffer boundaries for dcache ops
check_cache_range() warns that the top boundaries are not properly
aligned when flushing or invalidating the buffers and make these
operations fail.

This gets rid of the warnings:
CACHE: Misaligned operation at range ...

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-09-27 17:29:46 +02:00
Tom Rini
e120c848ba Merge branch 'master' of git://git.denx.de/u-boot-ubi 2016-09-27 10:47:37 -04:00
Tom Rini
6828e602b7 dfu: Migrate to Kconfig
Introduce a hidden USB_FUNCTION_DFU Kconfig option and select it for
CMD_DFU (as we must have the DFU command enabled to do anything DFU).
Make all of the entries in drivers/dfu/Kconfig depend on CMD_DFU and add
options for all of the back end choices that DFU can make use of.

Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
2016-09-27 10:46:45 -04:00
Tom Rini
6ad6102246 usb:gadget: Disallow DFU in SPL for now
Previously, DFU was not built in for SPL and often disabled via the board
config.h file, in the SPL build.  By moving DFU to Kconfig we now need to
move this logic to the Makefile to continue to allow boards to fit within
their SPL size limit (until gcc 6 is more widespread and unused strings will
be discarded).

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-27 10:46:20 -04:00
Tom Rini
5e61b0df41 ti_armv7_common.h: Adjust malloc pool size in all cases.
Previously we had been adjusting CONFIG_SYS_MALLOC_LEN based on if
CONFIG_DFU_MMC has been set or not.  However, for quite some time this
has not been the case as we often include <configs/ti_armv7_common.h>
prior to setting CONFIG_DFU_MMC so we would always use 16MiB and then
not have enough room for to DFU files.  Given the amount of memory we
always have, setting a minimum size of 32MiB for malloc is reasonable.
However, in the SPL case not only do we not need that much we start
running into overlap problems and then will fail to boot.  Since we
don't need 16MiB in the SPL case, bring this down to 8MiB.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-27 10:46:17 -04:00
Ladislav Michl
0061242236 cmd: ubi: add option to specify volume id
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
2016-09-27 07:00:12 +02:00
Tom Rini
cbe7706ab8 Merge git://git.denx.de/u-boot-fsl-qoriq
trini: Drop local memset() from
examples/standalone/mem_to_mem_idma2intr.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-26 17:10:56 -04:00
Heiko Schocher
8f2fe0c86c kconfig: introduce kconfig for UBI
move the UBI config options into Kconfig.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Reviewed by: Evgeni Dobrev <evgeni at studio-punkt.com>
2016-09-26 13:24:43 -04:00
York Sun
295a24b3d6 armv7: ls102xa: Rename GIC_ADDR and DCSR_RCPM_ADDR
Instead of using CONFIG_* name space, rename these two macros to
SYS_FSL_* space.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00
York Sun
5e8bd7e117 armv7: ls1021a: Convert CONFIG_LS1_DEEP_SLEEP to Kconfig option
Move this option to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
CC: Hongbo Zhang <hongbo.zhang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-09-26 08:53:07 -07:00