Commit graph

13186 commits

Author SHA1 Message Date
Patrice Chotard
a1b2faed7c phy: Be able to get phy from PHY provider
In case of phy are provided from a PHY provider nodes as following:

usbphyc: usb-phy@5a006000 {
	compatible = "st,stm32mp1-usbphyc";
	reg = <0x5a006000 0x1000>;
	clocks = <&rcc_clk USBPHY_K>;
	resets = <&rcc_rst USBPHY_R>;
	#address-cells = <1>;
	#size-cells = <0>;

	usbphyc_port0: usb-phy@0 {
		reg = <0>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <0>;
	};

	usbphyc_port1: usb-phy@1 {
		reg = <1>;
		phy-supply = <&vdd_usb>;
		vdda1v1-supply = <&reg11>;
		vdda1v8-supply = <&reg18>
		#phy-cells = <1>;
	};
};

and PHY are called as following:

usbh_ehci: usbh-ehci@5800d000 {
	compatible = "generic-ehci";
	reg = <0x5800d000 0x1000>;
	clocks = <&rcc_clk USBH>;
	resets = <&rcc_rst USBH_R>;
	interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
	companion = <&usbh_ohci>;
	phys = <&usbphyc_port0>;
	phy-names = "usb";
	status = "okay";
};

generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-19 16:31:35 -04:00
Patrick Delaunay
7d118161bb mmc: stm32_sdmmc2: update pwron management
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.

3 states managed in driver:
  1/ reset: SDMMC disable, signal HiZ
  2/ power-cycle: SDMMC disable, signals drive to 0
  3/ power-on: SDMMC enabled

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2018-07-19 16:31:35 -04:00
Luis Araneda
d600c4f6b0 drivers: fpga: zynqpl: fix compilation with SPL
Disable the use of function zynq_loadfs when compiling
the driver for the SPL, as the following filesystem
functions are not found by the linker:
- fs_set_blk_dev
- fs_read
- fs_set_blk_dev
- fs_read
- fs_read

Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:57 +02:00
Michal Simek
0bd83060c2 watchdog: cadence: Do not stop wdt in probe
Watchdog can be started before probe and u-boot should just take control
over it. That's why do not stop watchdog in probe to cover cases where
watchdog can expire before probe and start.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Michal Simek
6c253be7ce watchdog: cdns: Add comment for expire_now function
IP itself has no reg/no bit which can be used for this functionality.
Add this note to the driver to make sure that none will be asking for
that. Current method is to setup 1s timeout and hang() which is done via
wdt_expire_now().

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:56 +02:00
Michal Simek
4a69366967 microblaze: Convert generic platform to DM gpio
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
	compatible = "gpio-restart";
	gpios = <&reset_gpio 0 0 0>;
	/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Shreenidhi Shedi
e0e9caae6b watchdog: Convert Xilinx Axi watchdog driver to driver model
Xilinx Axi wdt driver conversion to driver model & Kconfig update
for the same.

Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Michal Simek
10441ec922 gpio: xilinx: Convert driver to DM
This patch is enabling GPIO_DM support to have an option to use this
driver together with zynq gpio driver.
!DM part is kept there till Microblaze is cleanup which will be done
hopefully soon.

Just a note:
There is no reason to initialize uc-priv->name because it is completely
unused.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Michal Simek
cae39ae365 sysreset: Add support for Microblaze soft reset jump
Microblaze is storing reset vector at address 0x0.
It means soft reset can be done by just jumping to this address.
This code was in platform code but sysreset interface is providing
enough capabilities to have more options how to reset the system. It can
go from gpio reset through watchdog reset till soft reset.

The driver has not compatible string because this is cpu specific and DM
core is not able to detect compatible string in DT root that's why this
driver will be instantiated from platform code by calling
device_bind_driver(gd->dm_root, "mb_soft_reset", "reset_soft",
NULL);
It should be bind as the last reset method to ensure that hw reset is
called before this.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:55 +02:00
Michal Simek
0d832b3221 sysreset: Add support for gpio-restart
The Linux kernel has binding for gpio-restart node.
This patch is adding basic support without supporting any optional
properties.
This driver was tested on Microblaze system where gpio is connected to
SoC reset logic.
Output value is handled via gpios cells values.

In gpio_reboot_request() set_value is writing 1 because
dm_gpio_set_value() is capable to changing it when it is ACTIVE_LOW.
...
	if (desc->flags & GPIOD_ACTIVE_LOW)
		value = !value;
...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:55 +02:00
Michal Simek
0d6fabb82d gpio: zynq: Setup bank_name to dev->name
There should be proper bank name setup to distinguish between different
gpio drivers. Use dev->name for it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:55 +02:00
Michal Simek
0df9bea434 gpio: zynq: Read of mach data in platdata with dev_get_driver_data
Remove bogus zynq_gpio_getplat_data() and read driver data directly.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Michal Simek
1b4c2aa25b gpio: dm: Support manual relocation for gpio
Relocate gpio ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Michal Simek
758de97bb8 sysreset: dm: Support manual relocation for sysreset
Relocate sysreset ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Michal Simek
946205a857 gpio: zynq: Fix typo in one error message
Just fix error message.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:54 +02:00
Michal Simek
f238b3f0fb watchdog: dm: Support manual relocation for watchdogs
Relocate watchdog ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Michal Simek
9713fac1eb watchdog: dm: Change uclass name to watchdog and enable DM_UC_FLAG_SEQ_ALIAS
uclass name is used by dev_read_alias_seq which return seq number when
aliases are used.

Code fragment:
168 int dev_read_alias_seq(struct udevice *dev, int *devnump)
169 {
170         ofnode node = dev_ofnode(dev);
171         const char *uc_name = dev->uclass->uc_drv->name;
172         int ret;
173
174         if (ofnode_is_np(node)) {
175                 ret = of_alias_get_id(ofnode_to_np(node), uc_name);

Also this patch enables DM_UC_FLAG_SEQ_ALIAS to be in sync with Linux
which is also using watchdog name for watchdog aliases.

drivers/watchdog/watchdog_core.c:215:
 ret = of_alias_get_id(wdd->parent->of_node, "watchdog");

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Siva Durga Prasad Paladugu
37e3a36a54 xilinx: zynq: Add support to secure images
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
   authenticated or encrypted or both authenticated and encrypted
   image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
   image back to DDR as per destination address. The image has
   to be encrypted using xilinx bootgen tool and to get only the
   encrypted image from tool use -split option while invoking
   bootgen.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:54 +02:00
Michal Simek
6bdf0a992c serial: zynq: Use platdata for storing static data instead of priv
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.

Platform data is created when the device is bound, and survives
probe/remove cycles.

Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."

Based on description the driver needs to be switch to use platdata
instead of priv.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-07-19 10:49:54 +02:00
Vipul Kumar
b4f015845a clk: zynqmp: Fixed the same if/else part error reported by coverity
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:53 +02:00
Michal Simek
d509f8dc5a gpio: zynq: Use live-tree function
Use live-tree function.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-07-19 10:49:53 +02:00
Tom Rini
1adbf2966a Merge branch 'master' of git://git.denx.de/u-boot-sunxi 2018-07-17 14:28:47 -04:00
Ludwig Zenz
51b2411946 sf: add paired dev info for winbond w25q16jv
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:17:13 +05:30
Ludwig Zenz
70cff76c38 sf: add Macronix mx25l1633e entry
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:14:42 +05:30
Ludwig Zenz
b1360e2fc9 sf: add Gigadevice gd25q16c entry
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)

Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:14:42 +05:30
Hannes Schmelzer
760b75564f spi_flash: add a bunch of winbond flashes to id-table
This commit adds the following flashes to the id-table

- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV

Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:05:50 +05:30
Siva Durga Prasad Paladugu
22cca1730e spi: zynqmp_gqspi: Add support for ZynqMP qspi driver
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:47 +05:30
Vipul Kumar
6e9d9fcb4c spi: xilinx_spi: convert to livetree
Update the xilinx spi driver to support a live tree.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Vipul Kumar
83ce646943 spi: xilinx_spi: Added support to read JEDEC-id twice at the boot time
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.

This patch added support to read JEDEC id in xilinx_spi_xfer ().

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Vipul Kumar
0c0de58f7b spi: xilinx_spi: Modify transfer logic xilinx_spi_xfer() function
This patch modify xilinx_spi_xfer() function and add rxfifo() and
txfifo() functions to add the modularity so that these functions
can be used by other functions within the same file.

This patch also added support to read fifo_size from dts.

Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Michal Simek
4e7c1a2651 spi: xilinx: Read reg base address from DTS file
This patch added support to read register base address from DTS file.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-07-16 14:01:20 +05:30
Lothar Felten
e46d73fa96 net: sun8i-emac: support R40 GMAC
Add support for the GMAC found in the Allwinner R40/V40 SoC.

The R40 GMAC interface is not controlled by the syscon register but
has a separate configuration register in the CCU.
The clock gate and reset bits are in a different register compared
to the other SoCs supported by this driver.
The driver uses the -gmac suffix for the R40 because the R40 also
has a different 100 MBit MAC (EMAC).

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:27:27 +05:30
Lothar Felten
c6a21d6615 net: sun8i-emac: set mux and clock by driver data
Use driver data->variant information to select device specific
pin mux and phy clock settings.

Suggested by Jagan Teki

Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
2018-07-16 12:27:27 +05:30
Lothar Felten
2f15743633 net: sun8i-emac: fix printing NULL character
If the variant is not set and therefore NULL, do not attempt to print
the variant.

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
2018-07-16 12:27:27 +05:30
Adam Sampson
979b239b4c dm: mmc: sunxi: Add A10/A20 compatible strings
Commit dd27918c22 ("dm: mmc: sunxi: Add support for driver model")
only added the allwinner,sun5i-a13-mmc compatible string for this
driver. The DM initialisation code here also works with (at least) A10
and A20, so add the appropriate compatible strings as per Linux 4.17's
driver.

Tested on A10 Cubieboard and A20 pcDuino3 Nano with CONFIG_DM_MMC.
(A20 worked already, because sun7i-a20.dtsi specifies both the A13 and
A20 strings.)

Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2018-07-16 12:25:47 +05:30
Tom Rini
914bb7ea2f Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- Update SPDX tag in arch/arm/mach-socfpga/spl_a10.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-07-13 14:47:04 -04:00
Ye Li
971490c892 lpi2c: Add bus busy error handling
When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but the master is idle, and stop is detected
(SDF set).

This patch addes a handling to re-init the lpi2c master for this
case. Then the issue can be worked around.

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-07-12 11:09:42 +02:00
Ye Li
d144f61ad3 lpi2c: Fix bus stop problem in xfer
In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command.  This causes a problem when reading register
data from i2c device.

Generally two operations comprise the register data reading:
   1. Write the register address to i2c device.
      START | chip_addr | W | ACK | register_addr | ACK |

   2. Read the Data from i2c device.
      START | chip_addr | R | ACK | DATA          | NACK | STOP

The STOP command should happen at the end of the transfer, otherwise
we will always get data from register address 0

Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-07-12 11:09:23 +02:00
Gao Pan
a32effd283 imx: lpi2c: fix clock issue when NACK detected
For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LPI2C master. As a result, we can never see the falling edge
of the ninth clock.

Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-07-12 11:09:07 +02:00
Ye Li
9b2ebcc060 imx_lpi2c: Update lpi2c driver to support imx8
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2018-07-12 11:08:41 +02:00
Marek Vasut
07252f6f7e ddr: altera: Add ECC DRAM scrubbing support for Arria10
The SDRAM must first be rewritten by zeroes if ECC is used to initialize
the ECC metadata. Make the CPU overwrite the DRAM with zeroes in such a
case. This scrubbing implementation turns the caches on temporarily, then
overwrites the whole RAM with zeroes, flushes the caches and turns them
off again. This provides satisfactory performance.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-12 09:22:12 +02:00
Marek Vasut
93a8ed8685 ddr: altera: Drop custom dram_bank_mmu_setup() on Arria10
This function was never used in SPL and the default implementation of
dram_bank_mmu_setup() does the same thing. The only difference is the
part which configures OCRAM as cachable, which doesn't really work as
it covers more than the OCRAM.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
0bc28b7cb8 ddr: altera: stratix10: Add DDR support for Stratix10 SoC
Add DDR support for Stratix SoC

Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
2018-07-12 09:22:12 +02:00
Ley Foon Tan
8b71e46cea spi: cadence_qspi: Fix warning cast from pointer to integer of different size
Use "%p" to print cmdbuf.

Compilation warning as below:

  CC      spl/drivers/spi/cadence_qspi_apb.o
  LD      spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
          cmdlen, (unsigned int)cmdbuf);

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Ley Foon Tan
9bd39dd8e5 spi: cadence_qspi: Fix compilation warning
Use "%zu" for size_t data type.

Compilation warning as below:

In file included from include/linux/bug.h:7:0,
                 from include/common.h:26,
                 from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);
        ^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
 #define pr_fmt(fmt) fmt
                     ^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
  debug_cond(_DEBUG, fmt, ##args)
  ^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
  debug("%s: len=%d [bytes]\n", __func__, data_bytes);

Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
2018-07-12 09:22:11 +02:00
Tom Rini
1612ff0dfb Merge branch 'master' of git://git.denx.de/u-boot-mips 2018-07-11 21:55:20 -04:00
Philippe Reynes
c38abed509 led: bcm6328: read base address in the parent node
In the device tree, the address for the led is located
in the parent node (for exemple leds), not in the led node
(for exemple led@0).

The commit "led: bcm6328: convert to use live dt"
(sha1: 8994551760)
change this behaviour and read the address in the led node.

We fix this by reading the base address for led
in the parent node.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-07-11 14:23:55 +02:00
Philippe Reynes
cef1f0c7a4 cpu: bmips: fix probe to get the address
In the device tree, the address for cpu is located in
the node "cpus", not in the cpu node (for exemple cpu@0).
So when probing cpu, the cpu address must be read in the
cpu parent.

The commit "cpu: bmips: convert to use live dt"
(sha1: c444afbbef)
change this behaviour and read the address in the
cpu node when probing cpu.

We fix this by reading the address in the cpu parent.

Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2018-07-11 14:23:55 +02:00
Adam Ford
6696de885e gpio: omap_gpio: Convert to auto-alloc feature when DT is supported
The omap_gpio driver has a TODO that says when every board is converted
to DM and DT, the omap_gpio_bind can stop using calloc and switch
to auto-alloc.

This patch converts this driver to auto-calloc when DT is enabled.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-10 16:55:58 -04:00
Thomas Fitzsimmons
894c3ad27f board: arm: Add support for Broadcom BCM7445
Add support for loading U-Boot on the Broadcom 7445 SoC.  This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.

Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
2018-07-10 16:55:57 -04:00