Commit graph

158 commits

Author SHA1 Message Date
Adam Ford
3275f26bb6 Convert CONFIG_BOOTP_SEND_HOSTNAME to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_SEND_HOSTNAME

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28 16:18:10 -04:00
Adam Ford
3879106414 Convert CONFIG_SPL_NAND_BASE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_NAND_BASE
   CONFIG_SPL_NAND_IDENT

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28 16:18:10 -04:00
Adam Ford
0c4a63438c Convert CONFIG_SPL_NAND_DRIVERS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SPL_NAND_DRIVERS
   CONFIG_SPL_NAND_ECC
   CONFIG_SPL_NAND_SIMPLE

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-28 16:18:10 -04:00
Adam Ford
7bb33e4684 ARM: da850-evm: Unify config options with Kconfig
There are two options that are currently whitelisted, but they
are redundant, because there are not necessary since Kconfig options
exist to basically state the same thing.

CONFIG_DIRECT_NOR_BOOT and CONFIG_USE_NOR are both set together and
only used by the da850 when booting from NOR, however the only time
CONFIG_MTD_NOR_FLASH is configured is when booting from NOR. Since
NOR doesn't need SPL, the options for SPL can be moved to a check for
building SPL instead of checking for NOR.

This patch removes the checks for these two config options and unifies
the checks around the Kconfig option of CONFIG_MTD_NOR_FLASH.

Since this board is the only board that uses these two config options,
they can be removed from the whitelist table.

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-07-13 20:58:34 +05:30
Tom Rini
e2dce7a532 Convert CONFIG_BOOTP_DNS2 to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_DNS2
   CONFIG_BOOTP_PXE_CLIENTARCH

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-26 10:29:05 -04:00
Ashok Reddy Soma
702de89cc6 treewide: mem: Move mtest related defines to Kconfig
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 12:02:56 -04:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Frieder Schrempf
832ce20278 mtd: spi: Clean up usage of CONFIG_SPI_FLASH_MTD
Most boards currently use SPI_FLASH_MTD only in U-Boot proper, not in
SPL. They often rely on hacks in the board header files to include
this option conditionally. To be able to fix this, we previously
introduced a separate option SPL_SPI_FLASH_MTD.

Therefore we can now adjust the Makefile and change the code in
sf_probe.c and sf_internal.h to use CONFIG_IS_ENABLED(SPI_FLASH_MTD).

We also need to move all occurences of CONFIG_SPI_FLASH_MTD from the
header files to the according defconfigs. The affected boards are
socfpga, aristainetos, cm_fx6, display5, ventana, rcar-gen2, dh_imx6
and da850evm.

We do this all in one patch to guarantee bisectibility.

This change was tested with buildman to make sure it does not
introduce any regressions by comparing the resulting binary sizes.

Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 00:48:32 +05:30
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Stefan Roese
c680df7e84 mtd: nand: raw: Move CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.

Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:58:37 -04:00
Adam Ford
1bf330150c Convert CONFIG_ARCH_CPU_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25 19:32:55 -04:00
Adam Ford
78f28773a5 Convert CONFIG_MX_CYCLIC to Kconfig
This converts the following to Kconfig:
   CONFIG_MX_CYCLIC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: David Lechner <david@lechnology.com>
2019-08-23 16:45:40 -04:00
Adam Ford
a6f14029e7 ARM: da850evm: Remove dead code
Now that SPL supports DM_SERIAL and the direct NOR boot supports
DM_SERIAL, the check to see if DM_SERIAL is defined can go away,
because all da850evm variants now support DM_SERIAL.  This patch
simply removes some dead precompiler defines.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20 11:46:38 -04:00
Adam Ford
5569304f1d ARM: da850evm: Remove dead SPI Code
With SPL now supporting DM_SPI, the need for compiler directives
and hard-coded addresses is obsolete.  This patch removes some
dead legacy code defining the SPI base address

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-20 11:46:38 -04:00
Adam Ford
d2c30190ee ARM: da850-evm: Increase environment NOR partition offset
The current size allocated to U-Boot is 384k, but U-Boot has grown
to 436K which means that saving the environmental variables wipes
out part of the U-Boot source and the board ceases to function.
Due to the sector and erase size for the NOR part and a desire to
not have to change partition sizes often, this patch moves the
U-Boot environmental variables to an offset of 1M so saveenv
does not brick the board.  This patch also sets up MTDIDS and
MTDPARTS to clearly show where U-Boot and U-Boot's environmental
variables are located.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-12 13:33:42 -04:00
Adam Ford
66e2637b19 ARM: da850-evm: Fix Lowlevel init
A previous patch for enabling the NAND config set a flag called
CONFIG_SKIP_LOWLEVEL_INIT when it should have been called
CONFIG_SKIP_LOWLEVEL_INIT_ONLY.  The affect this had was creating
a delay on startup for the NOR version which is XIP and doesn't have
SPL, so the lowlevel initialization functions need to operate.
This delay was not really noticeable at first, but the delays have been
getting longer, finally reached the point of nearly seven seconds
before the board would appear to start.

This patch sets the CONFIG_SKIP_LOWLEVEL_INIT_ONLY instead which means
"The normal CP15 init (such as enabling the instruction cache) is still
performed" per the README.  It doesn't appear to have any adverse
behavior on the SPI Flash or the NAND flash boards which use SPL.

Fixes: 93f3362762 ("ARM: configs: Add da850evm_nand to boot from NAND")

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-08-12 13:33:41 -04:00
Bartosz Golaszewski
95cffd9906 davinci: da850-evm: enable driver model for NAND
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.

On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
2019-07-29 17:58:52 -04:00
Adam Ford
3851f9be6b ARM: da850-evm: Remove dead/unneeded code
The DA8850-evm supports DM_I2C and boots with SPL_DM, so we can
drop some of the code which disables DM_I2C in SPL.  This
patch removes some #undef's now rendered obsolete.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-27 13:36:53 -04:00
Adam Ford
7f89cb29ef ARM: da850evm: Remove legacy OHCI referencs and unify platform
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed.  This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-27 13:36:53 -04:00
Adam Ford
95468e6c9b ARM: da850evm: Enable da850-ohci USB host controller
The DA850 EVM has one USB 1.1 OHCI Host controller.  With the
host controller now support DM_USB, this patch enables
the respective functions for the da850evm.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-05-05 08:48:50 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Adam Ford
15b8c75058 davinci: da850evm/omapl138-lcdk: Move BSS to SDRAM because SRAM is full
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.

This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR  set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.

Signed-off-by: Adam Ford <aford173@gmail.com>
2019-04-12 08:05:49 -04:00
Patrick Delaunay
abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00
Adam Ford
37ff057d94 board: da8xxevm: Fix Environmental CRC error
When the spi_flash_probe_bus_cs() was previously called, it was
called using 0's for two values where CONFIG_ENV_SPI_MAX_HZ and
CONFIG_ENV_SPI_MODE are now used.  When changed this
caused the environment to fail the CRC check and the default
was used.  This patch defines both of these values back 0.

Fixes: 25a17652c9 ("fix: env: Fix the SPI flash device setup
for DM mode")

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-11-26 22:52:12 -05:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Jagan Teki
cb19c29398 board: da8xxevm: Add SPL DM for serial, spi
This patch add SPL DM support for da8xxevm boards
with SPL serial, SPI drivers supported via platdata.

Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm
2018-10-10 11:53:55 +05:30
Adam Ford
973fcc8dae ARM: da850evm_direct_nor_defconfig: Enable DM_SERIAL
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-29 08:07:28 -04:00
Adam Ford
93f3362762 ARM: configs: Add da850evm_nand to boot from NAND
The DA850-EVM supports booting from NAND when used with the
UI expander board.  da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-09-11 21:37:31 -04:00
Adam Ford
9f8cf76be2 Convert CONFIG_SYS_I2C_DAVINCI to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_I2C_DAVINCI

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-17 15:43:38 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Adam Ford
5d653afc17 Convert CONFIG_DA8XX_GPIO to Kconfig
This converts the following to Kconfig:
   CONFIG_DA8XX_GPIO

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-23 14:33:21 -04:00
Adam Ford
9c5b00973b Convert CONFIG_MTD_PARTITIONS et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MTD_PARTITIONS
   CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-22 19:20:17 -04:00
Adam Ford
8d0d6bc121 configs: Convert CONFIG_USE_NAND to CONFIG_NAND
The DA850-EVM and OMAPL138_LCDK both use checks for CONFIG_USE_NAND.
This patch changes these checks to CONFIG_NAND which is already defined
in Kconfig.  Since the OMAPL138_LCDK already had CONFIG_NAND defined in its
defconfig, it can be deleted from configs/omapl138_lcdk.h.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-21 22:26:59 -04:00
Adam Ford
eba7f1ff6c Convert CONFIG_NAND_DAVINCI to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_DAVINCI

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-07-21 22:26:56 -04:00
Adam Ford
8e51c0f254 dm: gpio: Add DM compatibility to GPIO driver for Davinci
This adds DM_GPIO support for the davinici GPIO driver with
DT support.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-06-18 14:43:12 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Adam Ford
f1b1f77060 Convert CONFIG_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:11 -04:00
Marek Vasut
555004381e spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2018-04-11 13:22:00 -04:00
Tom Rini
6f6b7cfa89 Convert all of CONFIG_CONS_INDEX to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-03-16 10:28:52 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Tom Rini
75670c81e4 configs: Migrate CONFIG_SPL_FRAMEWORK
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig.  We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important.  In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-14 12:14:13 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Adam Ford
76e22222d3 Convert CONFIG_SYS_DV_CLKMODE et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_DV_CLKMODE
   CONFIG_SYS_DA850_PLL0_POSTDIV
   CONFIG_SYS_DA850_PLL0_PLLDIV1
   CONFIG_SYS_DA850_PLL0_PLLDIV2
   CONFIG_SYS_DA850_PLL0_PLLDIV3
   CONFIG_SYS_DA850_PLL0_PLLDIV4
   CONFIG_SYS_DA850_PLL0_PLLDIV5
   CONFIG_SYS_DA850_PLL0_PLLDIV6
   CONFIG_SYS_DA850_PLL0_PLLDIV7
   CONFIG_SYS_DA850_PLL1_POSTDIV
   CONFIG_SYS_DA850_PLL1_PLLDIV1
   CONFIG_SYS_DA850_PLL1_PLLDIV2
   CONFIG_SYS_DA850_PLL1_PLLDIV3

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-30 12:52:57 -05:00
Adam Ford
6aa4ad8e38 Convert CONFIG_SOC_DA8XX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SOC_DA8XX
   CONFIG_SOC_DA850
   CONFIG_DA850_LOWLEVEL
   CONFIG_MACH_DAVINCI_DA850_EVM
   CONFIG_SYS_DA850_PLL_INIT
   CONFIG_SYS_DA850_DDR_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-22 20:09:26 -05:00
Adam Ford
26410c1517 Convert CONFIG_DAVINCI_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_DAVINCI_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:30 -05:00
Adam Ford
3cf0061ab5 DA850evm: Remove dead code
There is an #ifdef and #endif with nothing in between.  This patch simply
removes this dead/useless code.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-19 15:49:28 -05:00