This adds PIC32 UART controller support based on driver model.
Signed-off-by: Paul Thacker <paul.thacker@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In PIC32 GPIO controller is part of PIC32 pin controller.
PIC32 has ten independently programmable ports and each with multiple pins.
Each of these pins can be configured and used as GPIO, provided they
are not in use for other peripherals.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In PIC32 pin-controller is a combined gpio-controller, pin-mux and
pin-config module. Remappable peripherals are assigned pins through
per-pin based muxing logic. And pin configuration are performed on
specific port registers which are shared along with gpio controller.
Note, non-remappable peripherals have default pins assigned thus
require no muxing.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PIC32 clock module consists of multiple oscillators, PLLs, mutiplexers
and dividers capable of supplying clock to various controllers
on or off-chip.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
For testing it is useful to be able to select the font size and the console
driver for sandbox. Add this information to platform data and copy it to
the video device when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way for the video console driver to be selected. This is
controlled by the video driver's private data. This can be set up when the
driver is probed so that it is ready for the video_post_probe() method.
The font size is provided as well. The console driver may or may not support
this depending on its capability.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This font is a little more ornate than normal. Example uses are on security
screens where a feeling of formality is required.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be used when a a friendly 'hand-writing' font is needed. It helps
to make the device feel familiar.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be used when a mono-space font is needed, but the console font
is too small (such as with high-DPI displays).
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing 8x16 font is adequate for most purposes. It is small and fast.
However for boot screens where information must be presented to the user,
the console font is not ideal. Common requirements are larger and
better-looking fonts.
This console driver can use TrueType fonts built into U-Boot, and render
them at any size. This can be used in scripts to place text as needed on
the display.
This driver is not really designed to operate with the command line. Much
of U-Boot expects a fixed-width font. But to keep things working correctly,
rudimentary support for the console is provided. The main missing feature is
support for command-line editing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
With proportional fonts the vidconsole uclass cannot itself erase the
previous character. Provide an optional method so that the driver can
handle this operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
When we start a new line (due to the user pressing return), signal this to
the driver so that it can flush its buffer of character positions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow the left margin to be set so that text does not have to be right up
against the left side. On some panels this makes it hard to read.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be sent when to many characters are entered. Make sure it is
ignored and does not cause a character to be displayed.
Signed-off-by: Simon Glass <sjg@chromium.org>
With anti-aliased fonts we need a more fine-grained horizontal position
than a single pixel. Characters can be positioned to start part-way through
a pixel, with anti-aliasing (greyscale edges) taking care of the visual
effect.
To cope with this, use fractional units (1/256 pixel) for horizontal
positions in the text console.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agust: rebased]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This is a header file which provides a fairly light-weight TrueType
rendering implementation. It is pulled from http://nothings.org/. The code
style does not comply with U-Boot but I think it is best to leave alone to
permit the source to be synced later if needed.
The only change is to fix a reference to fabs() which should route through
a macro to allow U-Boot to provide its own version.
Signed-off-by: Simon Glass <sjg@chromium.org>
With CONFIG_DM_PCI enabled, PCI buses are not enumerated at boot, as they
are without that config option enabled. No command exists to enumerate the
PCI buses. Hence, unless some board-specific code causes PCI enumeration,
PCI-based Ethernet devices are not detected, and network access is not
available.
This patch implements "pci enum" in the CONFIG_DM_PCI case, thus giving a
mechanism whereby PCI can be enumerated.
do_pci()'s handling of case 'e' is moved into a single location before the
dev variable is assigned, in order to skip calculation of dev. The enum
sub-command doesn't need the dev value, and skipping its calculation
avoids an irrelevant error being printed.
Using a command to initialize PCI like this has a disadvantage relative to
enumerating PCI at boot. In particular, Ethernet devices are not probed
during PCI enumeration, but only when used. This defers setting variables
such as ethact, ethaddr, etc. until the first network-related command is
executed. Hopefully this will not cause further issues. Perhaps in the
long term, we need a "net start/enum" command too?
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is not used as the use case for it did not eventuate. Remove
it to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for TPM ST33ZP24 spi.
The ST33ZP24 does have a spi interface.
The transport protocol is proprietary.
For spi we are relying only on DM_SPI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Add support for TPM ST33ZP24 family with i2c.
For i2c we are relying only on DM_I2C.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
I2C protocol is not standardize for TPM 1.2.
TIS prococol is define by the Trusted Computing Group and potentially
available on several TPMs.
tpm_tis_infineon.h header is not generic enough.
Rename tpm_tis_infineon.h to tpm_tis.h and move infineon specific
defines/variables to tpm_tis_infineon.c
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
TPM_TIS_LPC is connected to the LPC bus, not I2C.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Cortina phy cannot support soft reset, this commit implements probe
for Cortina PHY to tell phylib to skip phy soft reset by setting
PHY_FLAG_BROKEN_RESET in flags.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.
For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.
With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.
References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the 'autoneg' flag available in phydev when checking if
autoneg is in use.
The previous implementation was checking directly in the PHY
if autoneg was supported. Some PHYs will report that autoneg
is supported, even when it is disabled. Thus it is not possible
to use that bit to determine if autoneg is currently in use or
not.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When configuring a PHY in fixed (forced) link mode, in order for
the changes to be applied, either one of these conditions must
be triggered:
1- PHY is reset
2- Autoneg is restarted
3- PHY transitions from power-down to power-up
Neither of these is currently done, so effectively the fixed link
configuration is not applied in the PHY.
Fix this by setting the Autoneg restart bit.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.
The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.
Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function can fail, so be sure to report any errors that occur.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This property allows to specify fastest connection mode supported by
the MAC (as opposed to features of the phy).
There are situations when phy may handle faster modes than the
MAC (or even it's particular implementation or even due to CPU being too
slow).
This property is a standard one in Linux kernel these days and some
boards do already use it in their device tree descriptions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current implementation only sets "port select" bit for non-1Gb mode.
That works fine if GMAC has just exited reset state but we may as well
change connection mode in runtime. Then we'll need to reprogram GMAC for
that new mode of operation and if previous mode was 10 or 100 Mb and new
one is 1 Gb we'll need to reset port mode bit.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.
For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
This is a copy of the patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=c242a47238fa2a6a54af8a16e62b54e6e031d4bc
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
This is a copy of patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=5273e3a5ca94fbeb8e07d31203069220d5e682aa
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds driver model support to Freescale TSEC ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For internal routines like redundant_init(), startup_tsec() and
init_phy(), change to use tsec_private pointer as the parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust static functions in a proper order so that forward declaration
of tsec_send() can be avoided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
rxbd and txbd are declared static with 8 byte alignment requirement,
but they can be put into struct tsec_private as well and are natually
aligned to 8 byte.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present rx_idx and tx_idx are declared as static variables
in the driver codes. To support multiple interfaces, move it to
struct tsec_private.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Clean up the tsec and fsl_mdio driver codes a little bit, by:
- Fix misuse of tab and space here and there
- Use correct multi-line comment format
- Replace license identifier to GPL-2.0+
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}
A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.
For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When doing a software reset, the reset flag should be written without
other bits set. Writing the current state will lead to restoring the
state of the PHY (e.g. Powerdown), which is not what is expected from
a software reset.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Michael Welling <mwelling@ieee.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
