The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch initiates cros-ec in board_init() to enable it for smdk5250.
This patch depends on the patch in the MMC series that brings in exynos5-dt.c.
Refer to http://patchwork.ozlabs.org/patch/240084.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds cros-ec related device nodes to exynos5250-snow.dts.
It also adds a gpio node to exynos5250.dtsi.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add support for the Quad version of Wandboard; fix compile warning resulting
from having 2G of memory.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
add network support with ksz8851_16mll on at91sam9n12ek board
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
re-order the conditions which make the recovery system startup: combine
those conditions which were explicitly initiated (key press, software
request) and those which post-process error conditions (installer issues)
Signed-off-by: Gerhard Sittig <gsi@denx.de>
getenv() immediately after setenv() may perfectly legally return NULL, so
make sure to not deference an invalid pointer when creating diagnostic output
Signed-off-by: Gerhard Sittig <gsi@denx.de>
This patch adds the device node required for serial driver
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some Exynos5250 silicon may require 1.05v on the MIF to be stable, so to be
safe we can default to 1.05v instead of 1.00v. This can be set optimally later
in the boot process by the kernel.
The 0x6 value for 1.05v comes from the MAX77686 datasheet.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for the Palm Treo 680 smartphone. A quick overview of
u-boot implementation on the treo 680...
The treo 680 has a Diskonchip G4 nand flash chip. This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device. The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL). At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it. The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used. To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image. That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.
The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward. I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).
Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen. But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
This change is only done where needed: some linker
scripts may contain relocation symbols yet remain
unchanged.
__rel_dyn_start and __rel_dyn_end each requires
its own output section; putting them in relocation
sections changes their flags and breaks relocation.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This change is only done where needed: some linker
scripts may contain __image_copy_{start,end} yet
remain unchanged.
Also, __image_copy_end needs its own section; putting
it in relocation sections changes their flags and makes
relocation break.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Discard all .dynsym sections from linker scripts
Remove all __dynsym_start definitions from linker scripts
Remove all __dynsym_start references from the codebase
Note: this touches include/asm-generic/sections.h, which
is not ARM-specific, but actual uses of __dynsym_start
are only in ARM, so this patch can safely go through
the ARM repository.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Snow has an internal eMMC and an external SD card. Enable these in the
device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
"pixis_reset help" command prints the message without a new line "\n",
which makes the prompt on the same line.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PCIe TLB should be created with CONFIG_PCI defined
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a T4 board boots from SRIO or PCIE, it needs to finish these processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When a b4860qds board boots from SRIO or PCIE, it needs to finish these
processes:
1. Set all the cores in holdoff status.
2. Set the boot location to one PCIE or SRIO interface by RCW.
3. Set a specific TLB entry for the boot process.
4. Set a LAW entry with the TargetID of one PCIE or SRIO for the boot.
5. Set a specific TLB entry in order to fetch ucode and ENV from
master.
6. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
7. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
For more information about the feature of Boot from SRIO/PCIE, please
refer to the document doc/README.srio-pcie-boot-corenet.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e500v2 processor does not support 8K page size TLB entries.
So create new TLB entry only during NAND SPL boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB has 1GB DDR.
Out of this, only 880MB is passed on to Linux via bootm_size.
Remaining
-16MB is reserved for PowerPC-DSP shared control area
-128MB is reserved for DSP private area.
Also 256MB, out of this 880MB is required for data communication between
PowerPC and DSP core.
For this bootargs are modified to pass parameter to create 1 hugetlb
page of 256MB via default_hugepagesz, hugepagesz and hugepages
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB is a Freescale Reference Design Board for
BSC9131 SoC which is a integrated device that contains
one powerpc e500v2 core and one DSP starcore.
To support DSP starcore
-Creating LAW and TLB for DSP-CCSR space.
-Creating LAW for DSP-core subsystem M2 memory
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
BSC9131RDB supports Sysclk
-66MHz if jumper J16 is close (default state)
-100MHz if jumper J16 is open
Add targets
-BSC9131RDB_NAND_SYSCLK100 : for NAND boot at Sysclk 100MHz
-BSC9131RDB_SPIFLASH_SYSCLK100: for SPI boot at Sysclk 100MHz
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch allows to configure the net2big_v2 LEDs at startup (through
the GPIO extension bus). The front blue LED is enabled and the SATA rear
LEDs are configured to blink in relation with the SATA activity.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch adds support for the CPLD GPIO bus found on some LaCie boards
(as the 2Big/5Big Network v2 and the 2Big NAS). This parallel GPIO bus
exposes two registers (address and data). Each of this register is made
up of several dedicated GPIOs. An extra GPIO is used to notify the CPLD
that the registers have been updated.
Mostly this bus is used to configure the LEDs on LaCie boards.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch ensures minimal cooling for the net2big_v2 by automatically
starting the I2C fan (GMT G762) at low speed (2800 RPM).
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Fix the checkpatch warning on the panda.c file for leading
spaces.
Fix the CHECK warnings on the panda.c file for parenthesis alignment.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Detect if we are running on a panda revision A1-A6,
or an ES panda board. This can be done by reading
the level of GPIOs and checking the processor revisions.
This should result in:
Panda 4430:
GPIO171, GPIO101, GPIO182: 0 1 1 => A1-A5
GPIO171, GPIO101, GPIO182: 1 0 1 => A6
Panda ES:
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 0 1 1 => B1/B2
GPIO2, GPIO3, GPIO171, GPIO48, GPIO182: 0 0 1 1 1 => B3
Set the board name appropriately for the board revision that
is detected.
Update the findfdt macro to load the a4 device tree binary.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
[trini: %s/CONTROL_PADCONF_CORE/(*ctrl)->control_padconf_core_base/ and
formatting for that]
Signed-off-by: Tom Rini <trini@ti.com>
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
move rtc32k_enable() to common place so all am33xx boards can use it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables and initialises DWMMC for SMDK5250.
Supports both FDT and non-FDT. This patch creates a new file
'exynos5-dt.c' meant for FDT support.
exynos5-dt.c: This file shall contain all code which supports FDT.
Any addition of FDT support for any module needs to be
added in this file.
smdk5250.c: This file shall contain the code which supports non-FDT.
version. Any addition of non-FDT support for any module
needs to be added in this file.
May be, the file smdk5250.c can be removed in near future
when non-FDT is not required.
The Makefile is updated to compile only one of the files
exynos5-dt.c / smdk5250.c based on FDT configuration.
NOTE:
Please note that all additions corresponding to FDT need to be added into the
file exynos5-dt.c.
At same time if non-FDT support is required then add the corresponding
updations into smdk5250.c.
Signed-off-by: Amar <amarendra.xt@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds DWMMC device node data for exynos5.
This patch also adds binding file for DWMMC device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Amar <amarendra.xt@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
LP-8x4x is a programmable automation controller by ICP DAS. It is
shipped with outdated U-Boot v1.3.0
This patch adds enough supports to boot the board:
- 128M of 128M SDRAM
- 32M of 48M NOR Flash memory
- 1 of 4 Serial consoles (PXA FFUART)
- 2 of 2 Ethernet controllers (DM9000)
Signed-off-by: Sergey Yanovich <ynvich@gmail.com>
Series-to: u-boot
Series-cc: marex
Move pinmux configurations for the DA830 SoCs from board file
to the arch tree so that it can be used for all da830 based devices.
Also, avoids duplicate pinmuxing in case of NAND.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
Add MMC support for da830 boards in order to perform
mmc operations(read,write and erase).
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
After having the u-boot clean up series, there are
many definitions that are unused in header files.
Removing all those unused ones.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Jump into full u-boot mode if a 'c' character is received on the uart.
We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.
For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.
This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
No need to use the 'status' variable, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Add a DT simple-framebuffer node to DT when booting the Linux kernel.
This will allow the kernel to inherit the framebuffer configuration from
U-Boot, and display a graphical boot console, and even run a full SW-
rendered X server.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Simon Glass <sjg@chromium.org>
We need to call the save_omap_boot_params function on am33xx/ti81xx and
other newer TI SoCs, so move the function to boot-common. Only OMAP4+
has the omap_hw_init_context function so add ifdefs to not call it on
am33xx/ti81xx. Call save_omap_boot_params from s_init on am33xx/ti81xx
boards.
Reviewed-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Add minimal support (only boot from mmc device) for the Congatec
Conga-QEVAl Evaluation Carrier Board with conga-Qmx6q (i.MX6 Quad
processor) module.
Signed-off-by: Leo Sartre <lsartre@adeneo-embedded.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This requires that cpu_is_exynos4/5 should be made available before tzpc_init.
Hence this patch also makes necessary changes to have cpu_info in spl and
invokes arch_cpu_init before tzpc_init in low_level_init.S for smdk5250.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
tzpc_init is common for all exynos5 boards, hence move it to
armv7/exynos so that all other boards can use it.
Also update the smdk5250 Makefile and config file.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The number of gpio signal is packed inside CONFIG_SF_DEFAULT_CS macro
(shifted and or'ed with chip select), so it's incorrect to pass
that macro directly as an argument to gpio_direction_output() call.
Also, SPI driver sets the direction and initial value of a gpio,
used as a chip select signal, before any actual activity happens
on the bus.
So, it is safe to just remove the gpio_direction_output call,
that works incorrectly, thus making no effect, anyway.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Tested-by: Robert Winkler <robert.winkler@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There are 3 IO expanders on the mx6qsabreauto all reset by the
same GPIO, just set it to high to use the IO.
Signed-off-by: Renato Frias <b13784@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add i2c2 and 3 to mx6qsabreauto board, i2c3 is multiplexed
use gpio to set steering.
Signed-off-by: Renato Frias <b13784@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
VF610TWR is a board based on Vybrid VF610 SoC.
This patch adds basic support for Vybrid VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Did a 'strings u-boot-dtb-tegra.bin | less' and saw that both
board and board_name == beaver. Didn't test as I have no T30
Beaver board here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Current driver of p5040 assumes 10G port follows 1G port DTSEC5 in
eth port enum structure, it will assign mdio mux depend on this assumption.
This is not true with Fman V3, which added more 1G ports after port DTSEC5
in eth port enum structure, then 10G ports on p5040 will have wrong mdio mux.
So we use dynamic index for 10G ports instead of hardcoded enum value
when doing mdio mux for 10G ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
PC board has different serdes clock setting with PB board, it uses same
serdes frequency setting on bank2 as on bank1. PC board can be distingushed
from PB board by checking CPLD version, if running on PC board, then fix
the serdes reference clock frequency of bank2.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Crossbar switches were wrongly programmed to
route the CPRI lanes to SFP as the connectivity table
was not correct.
Modified it correctly for SFPs connections.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QSGMII card has different PHY address against previous SGMII card.
We check the type of card in slots and set correct PHY address to
avoid complainning "PHY reset timed out" during u-boot booting up.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
SW7[4] is the new bit which controls the mapping of eMMC vs SDHC.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- Added SERDES2 PRTCLs = 0x98, 0x9E
- Default Phy Addresses for Teranetics PHY on XAUI card
The PHY addresses of Teranetics PHY on XAUI riser card are assigned
based on the slot it is in. Switches SW4[2:4] and SW6[2:4] on
AMC2PEX-2S On B4860QDS, AMC2PEX card decide the PHY addresses on slot1
and slot2
- Configure MDIO for 10Gig Mac
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Debug trace buffers are memory mapped in DCSR space beyond 4M.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Provided a default RCW for P5040, then it can use PBL to build
ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Use QIXIS measurement registers to obtain sysclk and ddr clock. This
allows using non-standard clock speeds, set by directly writing to
clock chip or store the values in qixis clock data eeprom.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
QIXIS includes frequency measurement functions for each major processor
clock input. After reset (and after clocks are stable), QIXIS measures
the clocks against a reference frequency and stores the results in
CLK_FREQ registers. A base register supplies a multiplier which allows
directly obtaining the measured value, without requiring knowledge of
the target system or QIXIS core frequency.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Added a default RCW(1_28_6_12) and PBI configure file for T4240, so it can use
PBL tool to produce the ramboot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Allow VDD voltage overriding with a command. This is an add-on feasture of
VID. To override VDD, use command vdd_override with the value of voltage
in mV, for example
vdd_override <voltage in mV, eg. 1050>
The above example will set the VDD to 1.050 volt. Any wrong value out of
range of 0.8188 to 1.2125 volt or invalid string is ignored.
In addition to the command, if overriding VDD is needed earlier in booting
process, save an variable and reboot:
setenv t4240qds_vdd_mv <voltage in mV>
saveenv
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Print more detail information including core voltage, RCW source, switch
settings, etc. with bdinfo command.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add Seagate GoFlex Home support
Start with dockstar configuration
define support for RTC, DATE, SATA and EXT4FS
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
This patch creates a new config for the A5 dual core tile that includes the
generic config for the Versatile Express platform.
The generic config has been modified to provide support for the Extended
Memory Map, as used on the A5 core tile. A5 does not support the legacy
memory map.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
The current ca9x4_ct_vxp platform contains support for a Versatile
Express motherboard with a quad core A9 core tile.
This patch separates the Versatile Express motherboard code and the
A9 specific code, to ease supporting more core tiles in the next
patches.
Andre: merged the first two of Ryan's original patches and did some
checkpatch fixes.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Add sama5d3xek support with following feature
- boot from NAND flash, PMECC support, 4bit ECC @ 512 bytes sector
- boot from SPI flash support
- boot from SD card support
- LCD support
- EMAC support
- USB OHCI support
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
