Add node in DT and avoid error to search UCLASS_SYSRESET in
board_f.c::print_resetinfo() and lost 1.6s in U-Boot
for the trusted boot chain.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds independent watchdog support for stm32mp157c
in SPL.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update DDR configuration with the latest update:
- Change DQSGE to 1 for DDR3, to cure missing DQS preamble.
Signed-off-by: Nicolas Le Bayon <nicolas.le.bayon@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver.
According to the following tab (coming from STMFX datasheet), updates
have to done in stmfx_pinctrl_conf_set function:
-"type" has to be set when "bias" is configured as "pull-up or pull-down"
-PIN_CONFIG_DRIVE_PUSH_PULL should only be used when gpio is configured as
output. There is so no need to check direction.
DIR | TYPE | PUPD | MFX GPIO configuration
----|------|------|---------------------------------------------------
1 | 1 | 1 | OUTPUT open drain with internal pull-up resistor
----|------|------|---------------------------------------------------
1 | 1 | 0 | OUTPUT open drain with internal pull-down resistor
----|------|------|---------------------------------------------------
1 | 0 | 0/1 | OUTPUT push pull no pull
----|------|------|---------------------------------------------------
0 | 1 | 1 | INPUT with internal pull-up resistor
----|------|------|---------------------------------------------------
0 | 1 | 0 | INPUT with internal pull-down resistor
----|------|------|---------------------------------------------------
0 | 0 | 1 | INPUT floating
----|------|------|---------------------------------------------------
0 | 0 | 0 | analog (GPIO not used, default setting)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
STM32 RTC manages only 2 digits for YEAR
(Year tens and units in BCD format in RTC_DR register).
With this patch, RTC driver assumes that tm->tm_years is between
2000 and 2099; tm->tm_year - 2000 have only 2 digit
(0 > and <= 99).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
host->mmc, host->mmc->dev and host->mmc->priv must be set
before calling sdhci_setup_cfg() to avoid hang during mmc
initialization.
Thanks to commit 3d296365e4
("mmc: sdhci: Add support for sdhci-caps-mask") which put
this issue into evidence.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Increase SDMMC_BUSYD0END_TIMEOUT_US from 1s to 2s to
avoid timeout error during blocks erase on some sdcard
Issue seen on Kingston 16GB :
Device: STM32 SDMMC2
Manufacturer ID: 27
OEM: 5048
Name: SD16G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)]
host capabilities: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)]
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.5 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Issue reproduced with following command:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ... mmc erase failed
16384 blocks erased: ERROR
By setting SDMMC_BUSYD0END_TIMEOUT_US at 2 seconds and by adding
time measurement in stm32_sdmmc2_end_cmd() as shown below:
+start = get_timer(0);
/* Polling status register */
ret = readl_poll_timeout(priv->base + SDMMC_STA,
status, status & mask,
SDMMC_BUSYD0END_TIMEOUT_US);
+printf("time = %ld ms\n", get_timer(start));
We get the following trace:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ...
time = 17 ms
time = 1 ms
time = 1025 ms
time = 54 ms
time = 56 ms
time = 1021 ms
time = 57 ms
time = 56 ms
time = 1020 ms
time = 53 ms
time = 57 ms
time = 1021 ms
time = 53 ms
time = 57 ms
time = 1313 ms
time = 54 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
time = 1036 ms
time = 54 ms
time = 56 ms
time = 1028 ms
time = 53 ms
time = 56 ms
time = 1027 ms
time = 54 ms
time = 56 ms
time = 1024 ms
time = 54 ms
time = 56 ms
time = 1020 ms
time = 54 ms
time = 57 ms
time = 1023 ms
time = 54 ms
time = 56 ms
time = 1033 ms
time = 53 ms
time = 57 ms
....
time = 53 ms
time = 57 ms
time = 1021 ms
time = 56 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
1048576 blocks erased: OK
We see that 1 second timeout is not enough, we also see one measurement
up to 1313 ms. Set the timeout to 2 second to keep a security margin.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Read a single byte from EEPROM to verify that it is actually there.
This is equivalent to Linux kernel commit 00f0ea70d2b8 ("eeprom: at24:
check if the chip is functional in probe()").
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
hs: fixed style check prefer kernel type 'u8' over 'uint8_t'
i2c_idle_bus is already used in i2c_init_transfer. So before each transfer
if the bus is not ready, the i2c_idle_bus will be used to force idle.
It is unnecessary to call it again in probe.
We found a issue when enabling i2c mux with the mxc_i2c. The mxc_i2c is probed
after mux probing. However, at this moment the mux is still in idle state not
select any port. So if we call i2c_idle_bus in probe, it will fail and cause
mxc_i2c probe failed.
Signed-off-by: Ye Li <ye.li@nxp.com>
When requesting GPIO, the GPIOD_IS_OUT is missed in flag, so the GPIO
is set the input mode not output and cause mux not work.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add device tree for MPC8548CDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add CONFIG_RESET_VECTOR_ADDRESS definition with the default value
in u-boot.dtsi to fix the build error below. In the configuration
header file of some MPC85xx boards, there is not the definition
of CONFIG_RESET_VECTOR_ADDRESS, while CONFIG_SYS_MPC85XX_NO_RESETVEC
is also not defined. In this case, it will lack of definition of
CONFIG_RESET_VECTOR_ADDRESS in u-boot.dtsi, and the address
0xfffffffc will be used as the boot page by default.
Error log:
DTC arch/powerpc/dts/mpc8548cds.dtb
DTC arch/powerpc/dts/mpc8548cds_36b.dtb
Error: arch/powerpc/dts/u-boot.dtsi:28.15-16 syntax error
FATAL ERROR: Unable to parse input tree
Error: arch/powerpc/dts/u-boot.dtsi:28.15-16 syntax error
FATAL ERROR: Unable to parse input tree
scripts/Makefile.lib:308: recipe for target
'arch/powerpc/dts/mpc8548cds.dtb' failed
make[2]: *** [arch/powerpc/dts/mpc8548cds.dtb] Error 1
make[2]: *** Waiting for unfinished jobs....
scripts/Makefile.lib:308: recipe for target
'arch/powerpc/dts/mpc8548cds_36b.dtb' failed
make[2]: *** [arch/powerpc/dts/mpc8548cds_36b.dtb] Error 1
dts/Makefile:38: recipe for target 'arch-dtbs' failed
make[1]: *** [arch-dtbs] Error 2
Makefile:1038: recipe for target 'dts/dt.dtb' failed
make: *** [dts/dt.dtb] Error 2
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P5040DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P4080DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P3041DS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1041RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T1042D4RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T1024RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T4240RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add device tree for T2080RDB board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
include/video_logo.h once was created via the tool easylogo and than used
in cpu/mpc8xx/video.c to display Tux. video_logo.h has been replaced by
include/linux_logo.h and is not needed anymore.
Delete the include and the tool,
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Found accidentally in omap3_logic, CONFIG_USB_EHCI_OMAP adds some
code size to SPL, so this patch disables it on the am3517-evm to
reduce the code a bit since it's tight for space.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPI and NAND variants enable DM_GPIO, so this patch enables
DM_GPIO for the NOR / XIP version of the da850-evm.
Signed-off-by: Adam Ford <aford173@gmail.com>
The NAND configuration has had the ethernet missing, so this patch
enables the on-board ethernet interface.
Signed-off-by: Adam Ford <aford173@gmail.com>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, SPL/TPL options
when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit. In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
The current Makefile always use u-boot.bin to generate
PBL boot image (u-boot.pbl), this patch changes it to
use u-boot-with-dtb.bin to support device tree when
CONFIG_OF_SEPARATE is enabled.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
To address the following warning message:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
CONFIG_DM_USB is enabled, this resulted in SPL build errors:
drivers/built-in.o: In function 'xhci_dwc3_probe':
u-boot/drivers/usb/host/xhci-dwc3.c:155: undefined reference to 'usb_get_dr_mode'
scripts/Makefile.spl:404: recipe for target 'spl/u-boot-spl' failed
make[1]: *** [spl/u-boot-spl] Error 1
Makefile:1721: recipe for target 'spl/u-boot-spl' failed
make: *** [spl/u-boot-spl] Error 2
Enabling usb common library and usb ethernet drivers in SPL
does the job. Target was compile tested, build was clean.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
When large writes take place I saw a Samsung EVO 970+ return a status
value of 0x13, PRP Offset Invalid. I tracked this down to the
improper handling of PRP entries. The blocks the PRP entries are
placed in cannot cross a page boundary and thus should be allocated
on page boundaries. This is how the Linux kernel driver works.
With this patch, the PRP pool is allocated on a page boundary and
other than the very first allocation, the pool size is a multiple of
the page size. Each page can hold (4096 / 8) - 1 entries since the
last entry must point to the next page in the pool.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The command "pci bar" and "pci region" display the address and size in
16 characters including "0x", so the command can only display
14 hexadecimal digits if the number of digits in the address and size is
less than 14.
ID Base Size Width Type
----------------------------------------------------------
0 0x00000020000000 0x00000000100000 64 MEM Prefetchable
1 0xffff000080000000 0x00000000100000 64 MEM Prefetchable
The 64-bit address and size should be displayed in 18(= 16+2) digits,
so this patch adjusts them.
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some of the USB code is still being built into SPL even when the
SPL menu options have it explicitly disabled for SPL. Unit there is
a better solution, This patch undefines CONFIG_USB_EHCI_OMAP when
building SPL which reduces the code and lets the board boot again.
Fixes: 25e4ff45b1 ("ARM: omap3_logic: Enable OMAP EHCI support
for SOM-LV Boards")
Signed-off-by: Adam Ford <aford173@gmail.com>
The assigned value NULL is overwritten before being used. Remove the
assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To support KVM, we need to drop at EL2 and not EL1 before we boot Linux
kernel. This causes issues on platform with VHE and secondaries booting
at EL2 via TF-A PSCI CPU_ON call.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
earlyprintk no longer works on arm64 platforms. Replace it with earlycon
which works fine.
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: Liviu Dudau <liviu.dudau@foss.arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
File was found on specified location. Info about file was read,
but then immediately destroyed using 'free' call. As a result
file size was set to 0, hence fat process didn't read any data.
Premature 'free' call removed. Resources are freed right before
function return. File is read correctly.
Signed-off-by: Martin Vystrcil <martin.vystrcil@m-linux.cz>
The scsi_scan_dev() is looping over the number of uc_plat->max_id.
The number of actual ports a AHCI controller has can be greater than
max_id. Update uc_plat->max_id to make SCSI scan all detected ports.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When the pinmux configuration was added, it was accidentally placed into
the omap3_pmx_wkup node when it should have been placed into the
omap3_pmx_core. This error was accidentally propagated to U-Boot by
me when I blindly copied the device tree from Linux.
This patch moves the i2c2_pins and i2c3_pins to the correct node
which should eliminate i2c bus errors and timeouts due to the fact
the bootloader uses the save device tree that no longer properly
assigns these pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Noncached area at present is being initialized to random space after malloc
area. It works in most the cases as it goes to stack area & stack is not
overwriting it being far from it.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
When devnum was changed to a local variable in distro_bootcmd we ran
into a problem on TI platforms (confirmed on Beaglebone) as we had been
using 'setenv devnum' there as well and it needs to match the other
usage.
Fixes: 13dd6665ed ("distro: not taint environment variables if possible")
[trini: Review other platforms, re-word commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>