Add read for OTP and PMIC NVM with alternates
on virtual DFU device.
Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds the support of the spi nand device in mtdparts command
and in dfu_alt_info.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate the support of SPI NAND in stm32mp1 U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Generate automatically dfu_alt_info for the supported device.
The simple command "dfu 0" allows to start the dfu stack on usb 0
for the supported devices:
- dfu mtd for nand0
- dfu mtd for nor0
- dfu mmc for SDCard
- dfu mmc for eMMC
- dfu ram for images in DDR
The DUF alternate use the "part", "partubi" and "mmcpart" options
to select the correct MTD or GPT partition or the eMMC hw boot partition.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of DFU for MMC, MTD, RAM and MTD command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the sdmmc2 node for eMMC support on eval board stm32mp157c-ev1.
- update slew-rate for pin configuration
- update "vqmmc-supply"
- remove "st,sig-dir"
- add mandatory "pinctrl-names"
- add "mmc-ddr-3_3v"
This patch solve the eMMC detection issue for command "mmc dev 1".
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Device tree and binding alignment with kernel v5.4-rc4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.3
and converted to SPDX.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch allows to fix the following compilation warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
-----BEGIN PGP SIGNATURE-----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=4Z+A
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.01' of https://github.com/mbgg/u-boot
- add RPi4 upstream compatible to pinctrl
- fix boot banner on RPi3/4
- add support for one binary on RPi3/4
Enable the support of function keys on the USB keyboard. This is necessary
to test the USB keyboard driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow the unit test to pass full 8 byte scan code sequences to the USB
keyboard emulation driver and to parse multi-byte escape sequences.
The following features are not yet tested:
* LED status
* caps-lock
* num-lock
* numerical pad keys
The following features are not yet implemented by the USB keyboard
driver and therefore not tested:
* modifiers for non-alpha-numeric keys, e.g. <SHIFT><TAB> and <ALT><F4>
* some special keys, e.g. <PRINT>
* some modifiers, e.g. <ALT> and <META>
* alternative keyboard layouts
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move constant USB_KBD_BOOT_REPORT_SIZE. This allows us to reuse it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide support for F1-F12, Insert, Delete, Home, End, Page Up, Page Down.
As this leads to a size increase provide a customizing setting
CONFIG_USB_KEYBOARD_FN_KEYS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Avoid duplicate translation of arrow key codes.
Reduce code size by avoiding strings and eliminating
usb_kbd_put_sequence().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
usb_kbd_buffer is defined as u8[]. So let usb_kbd_put_queue() use u8 as
type of the parameter for the new byte.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In case the SPL on Gen5 loads U-Boot from NAND, unreset the NAND IP
explicitly in the platform code as the denali-spl driver is not aware
of DM at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
The NAND devices with 128 kiB erase blocks require extra 64 kiB padding
between each SPL image. Generate U-Boot image with such a padding using
this new target.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add new FPGA ID for ArriaV ST/D3 or SX/B3 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
On Gen5, when the FPGA is loaded and there was some prior interaction
between the HPS and the FPGA via bridges (e.g. Linux was running and
using some of the IPs in the FPGA) followed by warm reset, it has been
observed that there might be outstanding unfinished transactions. This
leads to an obscure misbehavior of the bridge.
When the bridge is enabled again in U-Boot and there are outstanding
transactions, a read from within the bridge address range would return
a result of the previous read instead. Example:
=> bridge enable ; md 0xff200000 1
ff200000: 1234abcd
=> bridge enable ; md 0xff200010 1
ff200010: 5678dcba <------- this is in fact a value which is stored in
a memory at 0xff200000
=> bridge enable ; md 0xff200000 1
ff200000: 90effe09 <------- this is in fact a value which is stored in
a memory at 0xff200010
and so it continues. Issuing a write does lock the system up completely.
This patch opens the FPGA bridges in 'bridge enable' command, the tears
them down again, and then opens them again. This allows these outstanding
transactions to complete and makes this misbehavior go away.
However, it is not entirely clear whether this is the correct solution.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
On Gen5, the 'bridge disable' command write 0x0 to brgmodrst register,
which releases all bridges from reset, instead of putting all bridges
into reset. Fix this by inverting the mask and actually putting the
bridges into reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Commit ec3dcea744 ("video: mxsfb: Configure the clock after eLCDIF reset")
causes boot regression on imx7d-pico/imx7d-sdb boards, so revert it
until a better solution is prepared.
This reverts commit ec3dcea744.
Reported-by: Joris Offouga <offougajoris@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Provide a defconfig which allows us to boot Raspberrry Pi 4
and Raspberry Pi 3 Model B/B+
Instead of using the embedded DTB as done in RPi3 we use the
devicetree provided by the firmware.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
For bcm283x based on arm64 we also have to change the mm_region.
Add assign this in mach_cpu_init() so we can create now one binary
for RPi3 and RPi4.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As part of the effort to create one binary for several bcm83x SoCs
we read the IO base address from device-tree.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We move the per SOC define BCM283x_BASE to a global variable.
This is a first step to provide a single binary for several bcm283x
SoCs.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The fw_dtb_pointer was defined in the assembly code, which makes him
live in section .text_rest
Put that's not necessary, we can push the variable in the .data section.
This will prevent relocation errors like:
board/raspberrypi/rpi/rpi.c:317:(.text.board_get_usable_ram_top+0x8):
relocation truncated to fit: R_AARCH64_LDST64_ABS_LO12_NC against symbol
`fw_dtb_pointer' defined in .text section in board/raspberrypi/rpi/built-in.o
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
