Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is taken directly from Linux kernel 6.3
(commit 457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 2564fce7ee ("sunxi: move Cortex SMPEN setting into start.S")
added SPL_ARMV7_SET_CORTEX_SMPEN to enable setting SMP bit. For
platforms not using SPL boot, add the corresponding non-SPL config,
so that CONFIG_IS_ENABLED(ARMV7_SET_CORTEX_SMPEN) works as expected.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The original function was only called once, before relocation. The new
one is called again after relocation. This was not the intent of the
original call. Fix this by renaming and updating the calling logic.
With this, chromebook_link64 makes it through SPL.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The OTG port is identified by inspecting the "dr_mode" property which is
expected to be "otg" for this port. But it will work just as well as a
device controller when dr_mode is set to "peripheral", which may be
required if the mode detection pin is not set up correctly and the
device controller needs to be programmed to override this.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of duplicating the string values here, use usb_get_dr_mode() to
handle the property lookup and converting the values to an enum.
This is implemented with a switch in preparation for the next patch
which adds extra handling for peripheral mode.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit 246450344dad arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
sync dts{,i} files for Radxa ROCK Pi 4 series with Linux 6.3.
because rk3399-rock-pi-4a.dts is enough for ROCK Pi 4A/B/A+/B+ and ROCK
4SE, delete dts{,i} for ROCK Pi 4B.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so fix ofnode_get_addr_size function with fdt_addr_t input to
be able to handle both sizes for stm32mp SoC in spl.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so fix some
debug strings with fdt_addr_t to be able to handle both sizes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Rockchip SoC rk3288 has 2 types of device trees floating around.
A 64bit reg size when synced from Linux and a 32bit for U-boot.
A pre-probe function in the syscon class driver assumes only 32bit.
For other odd reg structures the regmap must be defined in the individual
syscon driver. Store rk3288 platdata in a regmap before pre-probe
during bind.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Somehow, I managed to typo our company name in the U-Boot
and Linux kernel submissions.
Fix this and update the copyright year at the same time.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This synchronises the Linux device tree with U-Boot
(cp linux/..../fsl-ls1088a-ten64.dts uboot/..../fsl-ls1088a-ten64.dts),
as of Linux v6.2-rc5.
Missing from the U-Boot copy previously was the
Ethernet PCS definitions (required for linking with PHY in
Linux but not used by U-Boot) and various upstream
fixes and formatting changes.
The board microcontroller (which doesn't have a Linux driver)
has been moved to the -u-boot.dtsi, as well as the
spi0 quadspi alias (used by U-boot 'sf' but not valid for Linux).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Our [U-Boot] copy of fsl-ls1088a.dtsi had all the hardware under
the top level, until the DM_SERIAL implementation recently.
In this commit, remove any remaining devices (that were in U-Boot,
but not touched by previous patches in this series) to be under /soc,
updating to their upstream (Linux) bindings.
The bindings have been copied closest to their relative positions
in the Linux version, so the eventual result is that the U-Boot
and Linux fsl-ls1088a.dtsi will be identical.
The next commit will add the hardware bindings that were not
in U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the fsl-mc device tree definition under the /soc
node, as well as adding interrupt and IOMMU definitions that
were not in U-Boot before.
There are slight differences between the two bindings
as we add a "simple-mfd" compatible to function
under U-Boot's driver model.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the MDIO controller definitions with Linux, so
the controllers will be usable when passing U-Boot's
control FDT to Linux.
This also adds the PCS (internal controller) definitions
which are not used by U-Boot.
Caveat: The kernel definition uses "fsl,fman-memac-mdio",
as with other members of the Layerscape family, but
U-Boot uses a different driver for the DPAA2
Family devices (LS1088/LS2088/LX2160). So
we use "fsl,ls-mdio" as the first compatible string
for these devices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the USB device tree definition with Linux, allowing
the U-Boot control FDT to be used to boot a Linux system with
working USB.
An extra compatible string, "fsl,layerscape-dwc3" is needed
for special handling in U-Boot, so has been added to the
-u-boot.dtsi file. It might be better to add this to the
Linux source bindings.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
U-Boot's definition for the I2C controllers did not contain any
clock information. This resulted in the I2C not functioning when
the U-Boot control FDT was passed to Linux.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Move the GPIO controller definitions under the "soc" and in
the same relative position as the Linux kernel fsl-ls1088a.dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This is required for Linux to boot using the same FDT as
U-Boot (such as passing the control FDT to bootefi).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The Linux kernel fsl-ls1088a.dtsi disables (status="disabled")
all PCIe controllers by default, with the bootloader (i.e U-Boot)
enabling the appropriate controllers (specified by the board
reset control word/RCW) by FDT fixup.
However, U-Boot needs these controllers to be enabled
to be usable, which we can add in the u-boot only dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the PCIe controller definitions under /soc and adopts
the same bindings (fsl,ls1088a-pcie) as Linux. Previously,
the format was different between the two versions.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
To synchronise the device tree in U-Boot with Linux, the GIC
(Interrupt Controller) and SMMU/IOMMU nodes need to be synchronised
before changing any dependent components like PCIe and DPAA2/fsl-mc.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The top-level "memory" node does not exist in the Linux
version of the fsl-ls1088a.dtsi file. Move it to the U-Boot
"tweak" file, so we can have an identical copy of
fsl-ls1088a.dtsi between the projects in the end.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the bootph-all tags that were added in commit a593c1fec5
("arch: arm: dts: fsl-ls1088a.dtsi: tag serial nodes with bootph-all")
into a u-boot only include.
Due to the way the U-Boot device tree "tweak" system is setup[1],
we need to have a per-board <boardname>-u-boot.dtsi, which will
include the "fsl-ls1088a-u-boot.dtsi" tweaks.
By doing so, future updates to fsl-ls1088a.dtsi from upstream
(Linux kernel) can just be copied directly into the U-Boot tree,
without worrying about any extra data local to U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://u-boot.readthedocs.io/en/latest/develop/devicetree/control.html#adding-tweaks-for-u-boot
The CONFIG_SYS_SOC, CONFIG_SYS_CPU and CONFIG_SYS_VENDOR
values are the same for the entire Layerscape family,
meaning there is no ability to create a LS1088A only
file here. But we will be adding per-board tweaks
later in any case.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This a problem I found while updating the U-Boot fsl-ls1088a.dtsi
to match the Linux version.
fdt_fixup_remove_jr did not check whether there was a "crypto"
alias in the device tree before calling more fdt_* functions,
which resulted in a crash.
Fixes: a797f274
("ARMv8/sec_firmware : Update chosen/kaslr-seed with random number")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Update the DDR settings to those generated using 0.6 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Update the DDR settings to those generated using 0.9.1 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
On K3 HS-SE devices all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721s2 was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
Old map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
├─────────────────────────────────────┤ SYS_K3_MCU_SCRATCHPAD_BASE
│ SCRATCHPAD │ (0x41cff9fc)
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Create *-u-boot.dtsi files for each target dtb of the IOT2050 series so
that we can drop the #include deviations from upstream dts[i] files
here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
