We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create special function for reading bootmode on Versal and ZynqMP.
Zynq is using specific function (without mask) already.
Future patches will be calling this function from different location too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Parameter order is not correct based on zynqmp_mmio_write() declaration.
Fixes: be52372ff1 ("arm64: zynqmp: Use zynqmp_mmio_read/write functions")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Delay required for clock propagation is tighly coupled with initialization
done in psu_init(). That's why call it also for u-boot proper with
CONFIG_ZYNQMP_PSU_INIT_ENABLED enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
board_early_init_f() is the right location where debug uart can be
configurated (after MIO initialization).
The patch is taking this call from SPL to also make it available for U-Boot
proper.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP mini configurations works without PMU firmware that's why there is
no reason to enable the driver and check if it was probed properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Multi boot register can be used for using different boot images and design
better boot strategy. Let EL3 SPL or U-Boot to read it and print it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes: 312f2c5b14 ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The board has two push button connected to MIO pins
50 and 51, which have a pull-down resistor and are
connected to 1.8V when pressed.
These two pins are wrongly initialized with internal
pull-up enabled so they are reported as 1 all the time
with no change when pressed.
Disable the internal pull-up to fix the issue.
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds new jtag distro boot command to look for bootscript
file in DDR and execute it first incase of jtag bootmode.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DEVICE_TREE variable has been added by commit 6ab6b2afa0
("dts: re-write dts/Makefile more simply with Kbuild")
where DT can be specified on command line. If it is not then
CONFIG_DEFAULT_DEVICE_TREE is used to ensure backward compatibility.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Names have to match device tree file names. Also add missing one.
Fixes: 50d9283347 ("arm64: zynqmp: Sync names for SC with Versal")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initializationin low level code. Uart
driver does it already based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to do serial initialization. Uart driver does it already
based on DT. Good effect is that it is clear which interface is console.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
MIO34 is connected to POWER_KILL signal. When MIO configuration is done in
psu_init() and this pin is assigned to PMU but PMU configuration is not
loaded yet. PMU gpio output is high that means board is powered off
immediately.
The patch is fixing this sequence that MIO34 stays assing to ps gpio IP.
PMU config is loaded in SPL and then pin assigned to PMU through
psu_post_config_data().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_BOARD and OF_SEPARATE can use board specific board_fdt_blob_setup().
OF_BOARD option is mostly used for picking up DTB from certain location.
OF_SEPARATE option is used when DTB is appended after u-boot binary.
This board specific function is aligned with current version in
lib/fdtdec.c with checking CONFIG_XILINX_OF_BOARD_DTB_ADDR address first.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The reason for this change is just get in sync with board_fdt_blob_setup()
available at lib/fdtdec.c.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently "script_offset_f" env variable is hardcoded, this variable
specifies from which offset of the flash boot.scr should be read/write.
As flashes are of different sizes having a fixed offset makes it
difficult to load other images into the flash which may overwrite the
boot script or cannot utilize the full memory. This current fix
creates a new config "CONFIG_BOOT_SCRIPT_OFFSET" which holds the
offset address, overwrites the "script_offset_f" variable.
Also removed existing variable with default values, as the default
values are held by CONFIG_BOOT_SCRIPT_OFFSET
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to mmc@ff160000 controller on zynqmp.
Detect mmc alias at run time for setting up proper boot_targets
sequence instead of setting boot_targets manually.
Removed setting "modeboot" variable as it not longer need as we
switched to distro boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Emmc boot devcie is mounted to sdhci@f1050000 controller on versal, while
in emmc boot mode, boot tragets are set to mmc0. So removed mmc0 and using
the dev seq number from the sdhci@f1050000 controller.
Dev seq number is setup based on DT aliases that's why needs to be setup at
run time.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A number of board function belong in init.h with the others. Move them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_early_init_f added by commit e6cc3b25d7
("arm: zynq: Wire watchdog internals") is no longer needed that's why
remove it also with Kconfig enabling.
Fixes: ccd063e981 ("watchdog: Move watchdog_dev to data section (BSS may not be cleared)")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove macros which use PM_SIP_SVC offset and convert invoke_smc() to
xilinx_pm_request() which do calculation with PM_SIP_SVC already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the configuration naming to be generic to xilinx rather than
specific to Versal. The offset value is different for Zynq and ZynqMP
to avoid overlapping with FSBL.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move the exisiting function of getting board dtb from versal to a common
Xilinx folder.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Probe ZynqMP firmware driver on the board initialization phase and
ensure that firmware is in place to continue execution. The probing is
done on board_init so it can be used for both SPL and U-Boot proper.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new function from firmware version to get the firmware version.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New firmware header to place firmware specific macro and function
declarations. The patch also moves the macros defining PM operations as
well as some helper macros.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There were several changes in past in this file without removing headers
(watchdog cleanup, soft reset, etc). That's why remove additional useless
headers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup initrd_high and fdt_high to be placed in lowmem space for kernel to
be able to reach it. Values are setup at run time to ensure that the same
setting can be used on different memory setup. Do this setting only when
variables are not
Similar run time detection was done for Zynqmp and Versal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
