As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels
1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.
2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.
3. Kernel modules used in recovery mode should be independent
of vendor and odm partition
4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.
Due to these requirements, recovery image size has increased
to >10MB.
This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error
log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since CONFIG_DEFAULT_CONSOLE is already started with "console=",
the console argument in CONFIG_EXTRA_ENV_SETTINGS is expanded to
"console=console=ttySAC1,115200n8" and this causes the wrong
console device.
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
...
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=" CONFIG_DEFAULT_CONSOLE
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPM_NV_PER_PPREAD: physical presence needed for reading
TPM_NV_PER_WRITEDEFINE: persistent write lock by writing size 0
TPM_NV_PER_WRITEALL: write in one go
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to obtain random data from the TPM.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Added commit message, add cast to min()
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what
Linux does to sync libfdt. In order to make is possible, import
<linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
The fdt_region.c is U-Boot own file.
I did not touch them in order to avoid unpredictable impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this typedef in the same place as in Linux. This is necessary
to refactor libfdt inclusion.
U-Boot also defines it in include/compiler.h. Of course it should
not do that, but I do not want to open a can of worms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify fdt.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the falcon offsets for args to 16MB and kernel to 17MB
Since the below commit updated U-Boot proper location along
with rockchip boot image offsets
"spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip"
(sha1: 8f4d62b403)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using the ENV offset from rockchip legacy U-Boot for all SoCs,
the offset is 4MB-32KB
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We use the same default ENV setting in rockchip_common.h for all SoC.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove CONFIG_ENV_OFFSET for there already have one in rockchip_common.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip-common.h already defines values that are missing from
rk3368_common.h
For example BOOT_TARGET_DEVICES was defined empty and therefore
distroboot had no boot targets.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On Vybrid SoCs U-Boot gets loaded into GFX SRAM which is 512KiB.
Currently 32KiB is reserved for the IMX header. However, this is
not reflected in the size limit. In v2017.11-rc2 the actual size
limit (512KiB-32KiB) has been reached for Colibri VF61, which
lead to a successful build of U-Boot but not a working binary.
The IMX header is much smaller than 32KiB, typically around 1KiB.
Decrease the reserved size to 4KiB and specify the correct U-Boot
size limit. Apply this new base address and limit for all Vybrid
based boards.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
