In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Introduce the fundamental
device management capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for board configuration
to assign resources and other board related operations.
Introduce the board configuration capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
This patch enables DM_SERIAL for the pandora board. Verified that
the default kernel can still be booted with this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Change the configured serial console index to reflect that it is the
first physical UART, reorder some defconfig lines and move some
environment configuration from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You do not need to use the typedefs provided by compiler.
Our compilers are either IPL32 or LP64. Hence, U-Boot can/should
always use int-ll64.h typedefs like Linux kernel, whatever the
typedefs the compiler internally uses.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
setparity users has been updated to use new setconfig ops,
so we can safely remove setparity ops
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace setparity by more generic setconfig ops
to allow uart parity, bits word length and stop bits
number change.
Adds SERIAL_GET_PARITY/BITS/STOP macros.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When booting the QEMU virt machine with -net nic,model=e1000 we can already
support network boot just fine today.
So let's enable the default bootcmd to also evaluate DHCP responses properly.
That way we can enable network boot seamlessly with the virt target.
Signed-off-by: Alexander Graf <agraf@suse.de>
This commit adds support for the Toradex Colibri iMX7D 1GB Computer
on Module. The module is very similar to the Colibri iMX7D 512MB
but uses eMMC instead of raw NAND. This patch introduces a new
board specific Kconfig symbol to select between the two flash
options.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CONFIG_BOOTDELAY has been migrated to Kconfig, but cl-som-imx7 was
missed. We can just delete the assignments as the config already has
the correct value.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Convert the codes and configurations to enable DM drivers in u-boot for
modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI
This patch does not change SPL, so it still uses non-DM driver for
UART, GPIO and SD/MMC.
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
argc = 1: all tests are run
argc > 1: only argv[1] is run
So we need argc >= 1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have full Linux kernel boot support on EFI payload,
avoid pass "acpi=off" to the kernel command line.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present Linux kernel loaded from U-Boot as an EFI payload does
not boot. This fills in kernel's boot params structure with the
required critical EFI information like system table address and
memory map stuff so that kernel can obtain essential data like
runtime services and ACPI table to boot.
With this patch, now U-Boot as an EFI payload becomes much more
practical: it is another option of kernel bootloader, ie, can be
a replacement for grub.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This updates the EFI stub codes to pass UEFI BIOS's system table
address to U-Boot payload so that U-Boot can utilize it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix this sort of warning if generic-phy.h is included:
include/generic-phy.h:52:42: warning: ‘struct ofnode_phandle_args’ declared inside parameter list will not be visible outside of this definition or declaration
int (*of_xlate)(struct phy *phy, struct ofnode_phandle_args *args);
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Copy missing Kernel patch to make SLEWCTRL_SLOW available in device tree
and to correct the value of SLEWCTRL_FAST.
After this patch, the Kernel and U-boot device tree settings for
SLEWCTRL have the same effect.
Original Kernel patch message:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=424e0f039bfa8a51fb5c5178b6ece8baa4996469
"
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness. Current users of the macro (i2c and mdio) are left
unmodified as SLEWCTRL_FAST was the macro used and actual desired state.
Tested on am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"
Signed-off-by: Christian Amann <Christian.Amann@de.bosch.com>
Switch the Arria10 from ad-hoc hardcoded timer to timer framework
and the DW APB timer driver. This allows the A10 to extract timer
information, like timer rate, from clock framework and thus DT
instead of having it hardcoded in U-Boot configuration files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
This patch reverts the changes made for ls1088a and ls2080a
based boards in commit 18b6dd6cb0 ("armv8: layerscape: Drop
u-boot-with-spl.bin for selected boards").
u-boot-with-spl.bin is required for Gen3 based SoC where internal
ROM copy data in the internal memory
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Pramod Kumar <pramod.kumar_1@nxp.com>
CC: Ashish Kumar <ashish.kumar@nxp.com>
CC: York Sun <york.sun@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
A few fixes for 2018.09. Most noticable are:
- unbreak x86 target (-fdata-section fallout)
- fix undefined behavior in a few corner cases
- make Jetson TX1 boot again
- RTS fixes
- implement reset for simple output
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Zi4z
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-2018.09' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-08-21
A few fixes for 2018.09. Most noticable are:
- unbreak x86 target (-fdata-section fallout)
- fix undefined behavior in a few corner cases
- make Jetson TX1 boot again
- RTS fixes
- implement reset for simple output
Also add a 'drv' parameter to filter the children to remove/unbind.
Exporting those functions is a preparatory work for the addition of the
bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also add device_find_global_by_ofnode() that also find a device based on
the OF node, but doesn't probe the device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This function is the reciprocal of uclass_find_device().
It will be used to print the index information in dm tree dump.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With this update, the memory attributes are in sync with Linux
kernel v4.18-rc4. They also match page 190 of UEFI 2.7 spec [1].
[1] http://www.uefi.org/sites/default/files/resources/UEFI_Spec_2_7.pdf
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Starting with commit 867a6ac86d ("efi: Add start-up library code"),
sparse constantly complains about truncated constant value in efi.h:
include/efi.h:176:35: warning: cast truncates bits from constant value (8000000000000000 becomes 0)
This can get quite noisy, preventing real issues to be noticed:
$ make defconfig
*** Default configuration is based on 'sandbox_defconfig'
$ make C=2 -j12 2>&1 | grep truncates | wc -l
441
After the patch is applied:
$ make C=2 -j12 2>&1 | grep truncates | wc -l
0
$ sparse --version
v0.5.2
Following the suggestion of Heinrich Schuchardt, instead of only
fixing the root-cause, I replaced the whole enum of _SHIFT values
by ULL defines. This matches both the UEFI 2.7 spec and the Linux
kernel implementation.
Some ELF size comparison before and after the patch (gcc 7.3.0):
efi-x86_payload64_defconfig:
text data bss dec hex filename
407174 29432 278676 715282 aea12 u-boot.old
407152 29464 278676 715292 aea1c u-boot.new
-22 +32 0 +10
efi-x86_payload32_defconfig:
text data bss dec hex filename
447075 30308 280076 757459 b8ed3 u-boot.old
447053 30340 280076 757469 b8edd u-boot.new
-22 +32 0 +10
Fixes: 867a6ac86d ("efi: Add start-up library code")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The crc32 of the runtime services table must be updated after detaching.
efi_update_table_header_crc32() must be __efi_runtime. So move it to
efi_runtime.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Android documentation recommends new image format for storing DTB/DTBO
files: [1]. To support that format, this patch adds helper functions for
Android DTB/DTBO format. In image-android-dt.* files you can find helper
functions to work with Android DT image format, such us routines for:
- printing the dump of image structure
- getting the address and size of desired dtb/dtbo file
This patch uses dt_table.h file, that was added in commit 643cefa4d8
("Import Android's dt_table.h for DT image format") by Alex Deymo.
[1] https://source.android.com/devices/architecture/dto/partitions
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
There is no reason to have the same Kconfig options for different SoCs
separately. The patch is merging them together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[trini: Fix ENV_SIZE around ENV_IS_NOWHERE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
