P2041RDB supports 3 sysclk frequencies, it's selected by SW1[6~8],
software need to read the SW1 status to decide what the sysclk needs.
SW1[8~6] : frequency
0 0 1 : 83.3MHz
0 1 0 : 100MHz
others: 66.667MHz
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2041RDB has almost identical setup for TLB, LAWS, and PCI with
other P-Series CoreNet platforms.
The only difference between P2041RDB & P3041DS/P4080DS/P5020DS is the
CPLD vs PIXIS FPGA which we can handle via some simple #ifdefs in the
TLB and LAW setup tables.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.
The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
