Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The workaround to limit number of blocks to read in a single command
should only be applied to RK3568 and RK3588. Change to be more strict
when to apply the workaround.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
Add support for rk3588 phy variant.
The PHY clock is fixed at 100MHz.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
[kever.yang@rock-chips.com: update pcie pll parameters]
Co-developed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[eugen.hristev@collabora.com: squashed, tidy up]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some variants of the PHY have more than just one reset.
To cover all cases, request the rests in bulk rather than just
the reset at index 0.
Co-developed-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for max_link_speed specified in the PCI DT binding.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
[eugen.hristev@collabora.com: port to latest API, set default correctly,
align to 80 chars]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: switch to dev_read_u32_default]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.
This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")
Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.
Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Add pinctrl driver in SPL. Do not remove pinctrl properties for SPL dtb.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To be able to initialize the pinctrl correctly at SPL level and read
u-boot proper from SD-Card, the pinctrl must be initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fixes: 226fce6108 ("phy: Track power-on and init counts in uclass")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Add initial support for the rk3588 PHY variant.
The lookup for the host-port reg inside the struct now does a do {} while()
instead of a while() {} in order to allow a first check for reg == 0.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
phy-supply is now handled at uclass level. Remove it from the drivers that
implement it at the driver level.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Some phys require a phy-supply property that is a phandle to a regulator
that needs to be enabled for phy operations.
Implement basic supply lookup, enable and disabling, if DM_REGULATOR is
available.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[jonas@kwiboo.se:
use regulator_set_enable_if_allowed and disable if power_on ops fails]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Enable USB command, USB drivers, PHY and regulators, for USB host
operations.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
To quote the author:
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Define SPL_USB_ETH_RNDIS symbol to make it possible to select USB
gadget ethernet support in SPL and U-Boot separately in Kconfig .
Make use of the new symbols in gadget Makefile and move the rndis.o
just below the now merged USB_ETHER symbol in Makefile.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove leftover of
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
- Merge in a long-standing fix for some exynos platforms, correct a
Kconfig description, fix some env issues, fix an issue in
devfdt_get_addr_size_index_ptr and look for "panel-timings" not
"panel-timing" per upstream binding.
During refactor this seemed to have been missed.
Fixes: 65dbb128fb ("include: environment: ti: Use .env for environment variables")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For the devfdt_get_addr_size_index_ptr() function use
map_sysmem() function as cast for the return for use in
sandbox.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
In case where a single timing resolution is implemented in the
device-tree, the property is named "panel-timing", as specify
in Linux kernel binding file:
Documentation/devicetree/bindings/display/panel/panel-common.yaml
# Display Timings
panel-timing:
description:
Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings.
$ref: panel-timing.yaml#
display-timings:
description:
Some display panels support several resolutions with different timings.
The display-timings bindings supports specifying several timings and
optionally specifying which is the native mode.
$ref: display-timings.yaml#
Fixes: 0347cc7732 ("drivers: core: ofnode: Add panel timing decode.")
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
After converting my targets from CFG_EXTRA_ENV_SETTINGS to
CONFIG_EXTRA_ENV_TEXT as suggested by Tom, I discovered that
fw_setenv doesn't set the entire defaut environment anymore.
I tried to fix it with the below patch, but it fails qemu-x86 CI test,
see https://source.denx.de/u-boot/custodians/u-boot-mpc8xx/-/pipelines/16326
That's the only CI test that fails AFAICS.
Could you help with a solution ? This needs to be fixed.
Thanks
Christophe
---- >8 ----
From: Christophe Leroy <christophe.leroy@csgroup.eu>
Subject: [RFC PATCH] envtools: Fix default environment
After converting some targets from CFG_EXTRA_ENV_SETTINGS to
CONFIG_EXTRA_ENV_TEXT, default environment embedded in
fw_env tool missed all extra settings.
Commit 86b9c3e4e4 ("env: Allow U-Boot scripts to be placed in
a .env file") restricted the inclusion of the content of that
file to builds without USE_HOSTCC.
But as mentionned in commit 79fc0c5f49 ("tools/env: cross-compile
fw_printenv without setting HOSTCC"), HOSTCC and USE_HOSTCC are
kept for code re-use.
Remove the restricting so that settings included in a .env
file are also added to fw_env tool.
Fixes: 86b9c3e4e4 ("env: Allow U-Boot scripts to be placed in a .env file")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Otherwise non-ChromeOS samsung devices, like the odroid boards, are
stuck in a bootloop if CONFIG_CROS_EC is not enabled:
<...>
MMC: SAMSUNG SDHCI: 2, EXYNOS DWMMC: 0
Loading Environment from MMC... *** Warning - bad CRC, using default environment
cros-ec communications failure -96
Please reset with Power+Refresh
Cannot init cros-ec device
resetting ...
Issue started after commit e44d7e73fe ("dm: core: Switch
uclass_*_device_err to use uclass_*_device_check").
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
This reverts commit a034ec06ff.
Commit 4a3ea75de4 ("Revert "mmc: sdhci: set to INT_DATA_END when
there are data"") reverted the alternative fix that was added for
Exynos 4 devices, causing an error when trying to boot from an sdcard:
<...>
Loading Environment from MMC... sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
<...>
Re-add the quirk to allow booting from sdcards again.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Make it clear that this is the SPL option to avoid potential confusion
when the description for CONFIG_SPL_VIDEO is the same as that for
CONFIG_VIDEO.
Signed-off-by: John Keeping <john@metanate.com>
- Bring in a few kbuild changes from upstream Linux to fix running the
checker (make C=1/C=2), and clean up some of the logic related to how
choose what device trees to build.
A lot of errors are encountered when building with sparse checking
activated (make C=1 or make C=2).
Many of them are fixed in Linux.
Resynchronise Makefile and include/linux/build_bug.h with Linux
kernel sources by porting the following Linux commits into u-boot:
- 6c49f359ca14 ("kbuild: disable sparse warnings about unknown attributes")
- 80591e61a0f7 ("kbuild: tell sparse about the $ARCH")
- 8788994376d8 ("linux/build_bug.h: change type to int")
- 527edbc18a70 ("build_bug.h: remove most of dummy BUILD_BUG_ON stubs for Sparse")
- c60d3b79423a ("build_bug.h: remove negative-array fallback for BUILD_BUG_ON()")
- 14e83077d55f ("include: drop pointless __compiler_offsetof indirection")
Also revert commit aa9e891c63 ("include/linux/stddef.h: avoid
'warning: preprocessor token offsetof redefined'") because the
error it creates is worse than the warning it is trying to fix.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
[Linux commit 363547d2191c]
Currently DTB Overlays (.dtbo) are build from source files with the same
extension (.dts) as the base DTs (.dtb). This may become confusing and
even lead to wrong results. For example, a composite DTB (created from a
base DTB and a set of overlays) might have the same name as one of the
overlays that create it.
Different files should be generated from differently named sources.
.dtb <-> .dts
.dtbo <-> .dtso
We do not remove the ability to compile DTBO files from .dts files here,
only add a new rule allowing the .dtso file name. The current .dts named
overlays can be renamed with time. After all have been renamed we can
remove the other rule.
[Import notes: Adapt to U-Boot by using the cmd_dtco function instead
of cmd_dtc just like the current .dts -> .dtbo rule.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
[Linux commit b8fc5b2157b1]
If dtc is rebuilt, we should rebuild .dtb files with the new dtc.
[Import notes: Back then there was no .dtbo rule in Linux's
Makefile.lib, but the current .dtbo rules in Linux also have the
$(DTC) dependency, so also add it to our .dtbo rule.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The idea in 3609e1dc5f (dts: automatically build necessary .dtb
files) was fine, but the implementation was suboptimal due to some
misunderstandings on my part (and possibly defects in some defconfig
files):
- Sometimes DEFAULT_DEVICE_TREE is not included in OF_LIST or
SPL_OF_LIST
- SPL_OF_LIST is not always a subset of OF_LIST
- While SPL_OF_LIST governs the list of dtbs relevant to SPL (i.e.,
may be built into an
SPL-with-bunch-of-dtbs-to-choose-between-at-runtime), those dtbs are
not actually _built_ during the SPL build phase, i.e. when $(SPL_)
would expand to SPL_. fdtgrep runs on the artifacts produced during
the ordinary U-Boot build.
Tweak the logic so that we simply add the union of all dtbs mentioned
in either DEFAULT_DEVICE_TREE, OF_LIST and SPL_OF_LIST to dtb-y. That
should, for real, ensure that we always build all the dtbs that is
relevant to the current board, and should in turn enable us to
massively simplify arch/*/dts/Makefile.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building dtc from git causes the version number to start with a 'v'
(e.g. v1.7.0). printf then fails to parse 'v1' as a decimal value, and
prints '000700' instead of '010700'. Subsequently, the build fails,
because '000700' is less than the required '010400' version.
Signed-off-by: Martin Hundebøll <martin@geanix.com>
flash_get_size() will get the flash size from the device itself and go
through all erase regions to read protection status. However, the device
mappable region (eg: devicetree reg property) might be lower than the
device full size which means that the above cycle will result in a data
bus exception. This change fixes it by reading the 'addr_size' during
probe() and also use that as one possible upper limit.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
The mail ids of all the current Xilinx users are to be mapped to AMD
following the merger with AMD. The mailmap file is updated accordingly.
The ids of Marek Behún and Michal Simek are taken as reference.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The mailmap ids are not arranged in the dictionary order. So, sort the
mailmap ids in the dictionary order.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230426060104.10412-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This reverts commit e097847286. The
commit wrongly divides the dummy bytes by dummy bus width to calculate
the dummy bytes. The framework already converts the dummy cycles to the
number of bytes and the controller use the SPI flash command to
determine the dummy cycles via the address width.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230427065355.7413-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Some of the Kria SOM and ZynqMP boards are using Analog Devices ethernet
phy. So, enable CONFIG_PHY_ADIN for all ZynqMP platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230420085645.21260-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
