In generally it is not permitted to implement an ofnode function only for
flat tree or live tree. Both must be supported. Also the code for
live tree access should be in of_access.c rather than ofnode.c which is
really just for holding the API-conversion code.
Update ofnode_write_prop() accordingly and fix the test so it can work
with flat tree too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these to VESA, itself an abbreviation, to avoid a conflict with
Verified Boot for Embedded.
Rename this to avoid referencing VBE.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 44645f87de ("mmc: Fix mmc_switch excessive timeout") introduced
a side effect where CMD13 SEND_STATUS is issued in case mmc_wait_dat0()
does not return -ENOSYS and $send_status is not set. This happens on all
hardware which does implement .mmc_wait_dat0 callback, e.g. i.MX8M .
This leads to lengthy timeout before booting OS in case of eMMC in one
of the HS200/HS400 modes, since the card cannot respond to CMD13 while
downgrading from HS200/HS400 to regular HS mode.
Fix this by adding the missing conditional.
Fixes: 44645f87de ("mmc: Fix mmc_switch excessive timeout")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Release PERST# signal via GPIO when "reset-gpios" is defined in device tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
In more cases group name consist of function name followed by function
number. So if function name is just prefix of group name, show group name.
So in 'pinmux status -a' command output would be visible also extended
function number, which is useful for debugging.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
All 3 MPP pins (20, 21 and 22) can be configured individually and also can
be configured to GPIO functions. Fix definitions for these MPP pins in
existing pin groups. After this change GPIO function can be enabled just
for one of these 3 pins.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The last user of this driver was removed in commit dee08b1999 ("arm:
Remove gplugd board"). Remove the unused driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Pali Rohár <pali@kernel.org>
CMD_GENERAL_CONTROL takes two 8-bit arguments but CMD_EXT_CONTROL takes
two 16-bit arguments. Fix this issue and change CMD_EXT_CONTROL arguments
to 16-bit.
Fixes: 5e4d24ccc1 ("gpio: Add Turris Omnia MCU driver")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows you to specify the type of rgmii-id that will enable phy
internal delay in ethernet phy-mode.
This adds all RGMII cases to all of get_pinmode() except LD11, because LD11
SoC doesn't support RGMII due to the constraint of the hardware. When RGMII
phy mode is specified in the devicetree for LD11, the driver will abort
with an error.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We check if phydev is NULL. Only but if it is non-NULL we set one
component of phydev. But even if it is NULL we set another. We should not
dereference NULL in either case.
Fixes: e24b58f5ed ("net: phy: don't require PHY interface mode during PHY creation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reorder include files in the U-Boot expected order.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The convinience functions are not that small and they caused
bloated text segments because of their usage.
There was no need to inline them in the first place, as
they're not part of a fastpath.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Previously we'd been using a device name retrieved via
ftgmac100_data->phydev, but the mdio read/write functions may be
called before that member is initialized in ftgmac100_phy_init(),
leading to a NULL pointer dereference while printing the error message
issued if the mdio access fails. We can instead use bus->name, which
is already available at that point.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Fixes: 538e75d3fc ("net: ftgmac100: add MDIO bus and phylib support")
Reviewed-by: Cédric Le Goater <clg@kaod.org>
NPCM750 provides identical ethernet MAC controllers for WAN/LAN applications.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Only two boards in the tree set the macro DWC_NET_PHYADDR. Both have
CONFIG_DM_ETH_PHY=y, so should set the phy address in DT if necessary.
The imx8mp_evk does set the correct address in device tree.
The other board seems to be a copy-paste-adapt from an old
version of the imx8mp_evk config header, given the "#ifdef
CONFIG_DWC_ETH_QOS" block that has been removed from imx8mp_evk header
in commit 127fb45495. Its device tree doesn't even enable (i.e., set
'status = "okay"') the &eqos node. But the other ethernet device,
&fec, does get enabled, and does have a phy sitting at address 4 (and
it also has a corresponding legacy #define CONFIG_FEC_MXC_PHYADDR
4). So I believe it should be completely safe to remove it from there
as well.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[trini: Re-apply to top of tree, update imx93_evk.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
I have an iMX8MP with a ti,dp83867 phy in front of the eqos
interface. The phy is Gbit capable - however, the C and D differential
pairs are not physically routed to the RJ45 connector. So I need to
prevent the phy from advertising 1000Mbps.
The necessary code is almost already there in the form of a
phy_set_supported() call in eqos_start(), but the max-speed DT
property is currently only parsed in
eqos_probe_resources_stm32(). Lift that parsing to eqos_probe().
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Not only does eqos_remove() fail to free the buffers that have been
allocated by eqos_probe_resources_core(), it repeats those allocations
and thus drops twice as much memory on the floor.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Assign packet pointer only in case the MAC reports anything in the FIFO.
In case the MAC indicates empty FIFO, return 0 to pass that information
to the network stack.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This patch adds basic support for the Marvell 88E1240 PHY.
This will be used by the upcoming ethernet support addition for the
Marvell MIPS Octeon EBB7304 platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch adds support for the "marvell,reg-init" DT property, which
is used to describe board specific Marvell PHY register configurations
in the board dts file. This DT property is supported in the Linux Kernel
since a longer time. Adding it to U-Boot now, enables the boards which
describe the register settings in their DT files here as well.
I've included calling this marvell_of_reg_init() to all foo_config()
functions in this patch as well. If CONFIG_DM_ETH is not set, there is
no ofnode, or no "marvell,reg-init" property, the PHY initialization is
unchanged.
The function marvell_of_reg_init() is a port of the Linux version.
Please note that I explicitly did not add error checking and handling
to the U-Boot version, as this is basically not done for phy_read/write
in this Marvell PHY code.
This will be used by the upcoming ethernet support on the MIPS
Octeon EBB 7304 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
A large number of files include <flash.h> as it used to be how various
SPI flash related functions were found, or for other reasons entirely.
In order to migrate some further CONFIG symbols to Kconfig we need to
not include flash.h in cases where we don't have a NOR flash of some
sort enabled. Furthermore, in cases where we are in common code and it
doesn't make sense to try and further refactor the code itself in to new
files we need to guard this inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
As the only pic32 platform does not enable flash, this is dead code.
Remove it.
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FLASH_ERASE_TOUT
CONFIG_SYS_FLASH_LOCK_TOUT
CONFIG_SYS_FLASH_UNLOCK_TOUT
CONFIG_SYS_FLASH_WRITE_TOUT
In practice, for two m68k platforms we move to hard-coding with a
comment the timeout values, rather than try and make convoluted Kconfig
logic. We add options for the write and erase options to the pic32
flash driver, as this driver does make use of them. Everywhere else
these are unreferenced values.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit 83061dbd1c ("Rename GPIO_SUPPORT to GPIO"),
SPL_GPIO_SUPPORT has been renamed to SPL_GPIO, meaning that SPL_GPIO_HOG
can never be enabled.
Let's fix this by using the proper name for the Kconfig option.
Fixes: 1d99e673c7 ("gpio: Enable hogging support in SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some setups do not use Xen hypervisor console for logging, e.g. they
use emulated PL011 hardware or shared peripherals (real UART). In such
cases Xen HVC will be disabled on a build time and will cause issues in
current driver implementation.
This commit fixes build issues in Xen event channel driver, caused
by absense of console event channel, that is not available when console
config is disabled. Now console related code will be removed when
Xen HVC is turned off.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com<mailto:vicooodin@gmail.com>>
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com<mailto:dmytro_firsov@epam.com>>
To work correctly, this driver depends on SYSCON to get the base address
from the parent dts node.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
The TPM device comes with the random number generator(RNG)
functionality which is built into the TPM device. Add logic to add the
RNG child device in the TPM uclass post probe callback.
The RNG device can then be used to pass a set of random bytes to the
linux kernel, need for address space randomisation through the
EFI_RNG_PROTOCOL interface.
No compatible string is provided because this is not available in
the binding defined by Linux. If multiple rand devices are in the
system, then some method of selecting them (other than device tree)
will need to be used, or a binding will need to be added.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The TPM device has a builtin random number generator(RNG)
functionality. Expose the RNG functions of the TPM device to the
driver model so that they can be used by the EFI_RNG_PROTOCOL if the
protocol is installed.
Also change the function arguments and return type of the random
number functions to comply with the driver model api.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Linux kernel uses compatible string "marvell,armada370-nand-controller" for
nand controllers on Armada 370/XP/38x. U-Boot currently uses mix of
"marvell,armada370-nand" and "marvell,mvebu-pxa3xx-nand".
So unify it and use just Linux kernel compatible string.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver registers GPIO controller and allows U-Boot to control GPIO
pins on MCU which is connected to Turris Omnia via i2c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Current pin control driver applies SDHCI PHY MUX selection
when board DT calls for eMMC function on MPP wires.
However, for CP side eMMC, only the "armada-8k-cpm-pinctrl"
compatibility string is taken into account, which causes
CP-SDHCI on Armada-7K boards to fail.
This patch adds "armada-7k-pinctrl" compatibility string
handling for the CP-SDHCI PHY configuration case.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
These functions are required for 'pinmux status -a' command to print
current configuration of each MPP pin.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To automatically enable GPIO functionality of some MPP pin, it is required
to implement .gpio_request_enable and .gpio_disable_free callbacks in
pinctrl driver and set .request and .rfree callbacks in GPIO driver to
pinctrl_gpio_request / pinctrl_gpio_free functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently bank name is just one alphabetical letter.
Change it to mvebu and number.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Device tree property "ngpios" contains number of gpios.
Use it when available.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To use particular pin GPIO, it needs to be first switched to GPIO by
pinctrl. Use pinctrl_gpio_request() and pinctrl_gpio_free() for this
purpose.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This change allows to use pinctrl_gpio_request() function as a direct
pointer for dm_gpio_ops's .request callback.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This new Armada 38x driver is based on Linux kernel driver. It can set any
pin to any valid function specified in DT like Linux kernel, it provides
support for 'pinmux status -a' command and also for pinctrl_gpio_request().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This new function pinctrl_generic_set_state_prefix() behaves like
pinctrl_generic_set_state() but it takes third string argument which is
used as the prefix for each device tree string property.
This is needed for Marvell pinctrl drivers, becase Linux device tree files
have pinmux properties prefixed by "marvell," string.
This change allows to use generic U-Boot pinctrl functions for Armada 38x
pinctrl driver without need to copy+paste of the majority U-Boot pinctrl
code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
sandbox_defconfig builds the PCI MMC driver. It should be possible to
build the sandbox without ACPI support.
ACPI support in the PCI MMC driver is only needed when creating an ACPI
table. Fix building with ACPIGEN=n.
Fixes: dba7ee419d ("acpi: mmc: Generate ACPI info for the PCI SD Card")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add features to write protect single boot area rather than all boot
areas.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Only newer eSDHC controllers set PRSSTAT_SDSTB flag. So do not wait until
flag PRSSTAT_SDSTB is set on old pre-2.2 controllers. Instead sleep for
fixed amount of time like it was before commit 6f883e501b ("mmc:
fsl_esdhc: Add emmc hs200 support").
This change fixes error 'Internal clock never stabilised.' which is printed
on P2020 board at every access to SD card.
Fixes: 6f883e501b ("mmc: fsl_esdhc: Add emmc hs200 support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
By reading binman symbols, we no need hard coded IMEM_LEN/DMEM_LEN after
we update the binman dtsi to drop 0x8000/0x4000 length for the firmware.
And that could save binary size for many KBs.
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8m[m,n,p]-venice
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
[Alper: Check BINMAN_SYMS_OK instead]
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Since new atheros PHY driver needs to access its PHY node through
phy device, we have to assign the phy node in ethernet controller
driver. Otherwise the PHY driver will fail to get some nodes
and properties.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move i.MX code to a standalone file to make it easy for adding new
platform support
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move macros and structures to header file and make some functions
public, so that could used by other files, this is to
prepare split platform specific config to one file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When CONFIG_CLK is not enabled, there will be buil break:
"error: ‘eqos’ undeclared (first use in this function)"
Take eqos definition out the CONFIG_CLK ifdef.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig for enabling reference events counter in DDRC performance
monitor by default
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since i.MX9 uses same DDR PHY with i.MX8M, split the DDRPHY to a common
directory under imx, then use dedicated ddr controller driver for each
iMX9 and iMX8M.
The DDRPHY registers are space compressed, so it needs conversion to
access the DDRPHY address. Introduce a common PHY address remap function
for both iMX8M and iMX9 for all PHY registers accessing.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sentinel have read access of OTP shadow register 0-511, and fsb have
read access of shadow 0-51/312-511.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX93 fuse can be accessed through FSB and s400-api. Add mapping tables
for i.MX93. The offset address of FSB accessing OTP shadow registers is
different between i.MX8ULP and i.MX93, so use macro to define the offset
address instead of hardcode.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The i.MX93 platform wants to reuse drivers/misc/imx8ulp/fuse.c. Moving
fuse.c from the folder imx8ulp to sentinel makes it can be used by other
platforms.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce Sentinel API ahab_release_m33_trout to make sure sentinel
release M33 trout and make sure M33 could boot.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support more RDC instances on i.MX93, update API to latest
definition.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Replace logically correct word in the description.
Fixes: 91a91ff804 ("dm: Add Kconfig options for driver model SPL support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
If parameter drv of lists_bind_fdt() is specified, we shall bind only to
this very driver and to no other.
If the driver drv has an of_match property, we shall only bind to the
driver if it matches the compatible string of the device.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If parameter drv of lists_bind_fdt() is specified, we want to bind to this
specific driver even if its field of_match is NULL.
If entry->of_match is NULL, we should not dereference it in a debug
statement.
Fixes: d3e773613b ("dm: core: Use U-Boot logging instead of pr_debug()")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When programming qspi flash speed we need to check the requested flash
speed not to exceed the spi max frequency. In the current implementation
we are checking qspi ref clk instead. This commit fixes the issue by
checking the requested speed and programs the specified max frequency.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-5-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support_ops function zynq_qspi_mem_exec_op to check controller
supported operations by spi-mem framework. Current default support ops
function does not allow dummy buswidth no more than 1, unless we are
using buswidth is 4 for TX.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-4-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add child pre probe function in the driver. Update max_hz of priv from
spi_slave structure.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657893679-20039-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support_ops function to check controller supported operations by
spi-mem framework. Current default support ops function does not allow
dummy buswidth no more than 1, unless we are using buswidth is 4 for TX.
In order to support dummy buswidth > 1 by spi-nor framework we are adding
explicit support_ops to check controller supported operations.
Fix dummy bytes calculation incase of valid dummy bytes when dummy
buswidth is > 1. Current dummy bytes calculation does not provide
correct dummy values for dummy buswidth > 1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657954727-31972-3-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for spi memory operations for xilinx AXI qspi driver.
This provides an high-level interface to execute SPI memory
operations by the controller.
Remove existing spi transfer based implementation and use
spi memory based exec_op() implementation for qspi IO operations.
Simplified existing startup_block implementation.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1657954727-31972-2-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add supporting new compatible string "u-boot,zynqmp-fpga-enc" to
handle loading encrypted bitfiles.
This feature requires encrypted FSBL, as according to UG1085:
"The CSU automatically locks out the AES key, stored in either BBRAM
or eFUSEs, as a key source to the AES engine if the FSBL is not
encrypted. This prevents using the BBRAM or eFUSE as the key source
to the AES engine during run-time applications."
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-14-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reduce the function code by calling xilinx_pm_request() once only.
Use the same variable bsize_req to store either bstream size in bytes
or an address of bstream size according to a type required by the
firmware version. Remove obsolete debug().
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-11-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-10-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a "compatible" string to binary flag converter, which uses
a callback str2flag() of given FPGA driver if available.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-8-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
These flags may be used to check whether an FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-7-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
This flag is used to check whether a Xilinx FPGA driver is able to
load a particular FPGA bitstream image.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-6-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add a call to convert FPGA "compatible" string to a binary flag.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-5-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
It allows using this feature without enabling the "fpga loads"
command.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Co-developed-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Tested-by: Ricardo Salveti <ricardo@foundries.io>
Tested-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Link: https://lore.kernel.org/r/20220722141614.297383-2-oleksandr.suvorov@foundries.io
Signed-off-by: Michal Simek <michal.simek@amd.com>
After commit 8cca60a2cb ("Kconfig: Remove some symbols from the
whitelist") downstream builds failed for boards setting this in
include/configs/…
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://lore.kernel.org/r/20220721133122.32428-2-ada@thorsis.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable power domain driver to configure pmufw config object and request
node for all the IP's that are enabled in DT.
This driver depends on mailbox and IPI driver, hence enable them as well.
Add ARCH_VERSAL in the depends on of mailbox Kconfig to compile for
Versal platforms.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-6-ashok.reddy.soma@xilinx.com
Mailbox driver might be need for Versal and other future platforms.
To remove the dependency, move struct zynqmp_ipi_msg to
zynqmp_firmware.h so that mailbox driver compiles for other platforms
easily.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-5-ashok.reddy.soma@xilinx.com
Try loading pmufw config overlay for core0, if it doesn't return any
error it means pmufw is accepting nodes for other IP's. Otherwise dont
try to load config object for any other IP, just return from
zynqmp_pmufw_node function.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-3-ashok.reddy.soma@xilinx.com
zynqmp_pmufw_load_config_object() has some error cases and it is better
to return those errors. Change prototype of this function to return
errors.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220722084658.30995-2-ashok.reddy.soma@xilinx.com
Add support for versal platform by adding "xlnx,versal-reset"
compatible string in zynqmp-reset driver. Reset numbering schema
for versal is not same as zynqmp, so nr_reset and reset_id are
set to zero. In case of assert/dessert, required device reset id
is sent from respective driver through struct reset_ctl.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220720095959.29610-2-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Since the calulation of "bgen" is rounded down, using a higher
baudrate will result in a larger difference from the actual
baudrate. Should use DIV_ROUND_CLOSEST() like the Linux driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1657676339-6055-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Timing macro's are wrong for MMC_HS_52 and MMC_DDR_52. Fix it with
correct values of MMC_TIMING_MMC_HS and MMC_TIMING_MMC_DDR52 respectively.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1656319965-12124-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This commit fixes issue with usage of Xen hypervisor shared info page.
Previously U-boot did not unmap it at the end of OS boot process. Xen
did not prevent guest from this. So, it worked, but caused wierd
issues - one memory page, that was returned by memalign in U-boot
for Enlighten mapping was not unmaped by Xen (shared_info values was
not removed from there) and returned to allocator. During the Linux
boot, it uses shared_info page as regular RAM page, which leads to
hypervisor shared info corruption.
So, to fix this issue, as discussed on the xen-devel mailing list, the
code should:
1) Unmap the page
2) Populate the area with memory using XENMEM_populate_physmap
This patch adds page unmapping via XENMEM_remove_from_physmap, fills
hole in address space where page was mapped via XENMEM_populate_physmap
and return this address to memory allocator for freeing.
Signed-off-by: Dmytro Firsov <dmytro_firsov@epam.com>
Reviewed-by: Anastasiia Lukianenko <vicooodin@gmail.com>
The first AM6x device was the AM654x, but being the first we named it
just AM6, since more devices have come out with this same prefix we
should switch it to the normal convention of using the full name of the
first compatibility device the series. This makes what device we are
talking about more clear and matches all the K3 devices added since.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For SDCC version 5.0.0, MCI registers are removed from SDCC interface
and some registers are moved to HC. So add support to use the new
compatible string "qcom,sdhci-msm-v5". Based on this new msm variant,
pick the relevant variant data and use it to detect MCI presence thereby
configuring register read/write to msm specific registers.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
"apple,t8112-dart" uses an incompatible register interface but still
offers the same functionality. This DART is found on the M2 and M1
Pro/Max/Ultra SoCs.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The imx6q arm2 board support has been removed from U-Boot
as it did not get converted to DM.
Remove the MX6Q_ARM2 related ifdefery in the driver.
Signed-off-by: Fabio Estevam <festevam@denx.de>
In preparation of re-sync of mtd stack, we opt to move the current stack
slowly in order to have a more easy sync and test. We would like to
prepare uboot to support no-jedec and no-onfi compliant nand so we need
to clean up a bit the code we have now and upstream some of the support.
In this series we expect no functional change
Tested on:
- imx6ull Micron MT29F2G08ABAGAH4
- imx8mn Macronix MX30LF4G18AC
Upstream linux commit f7025a43a9da26.
The MTD subsystem has its own small museum of ancient NANDs in a form of
the CONFIG_MTD_NAND_MUSEUM_IDS configuration option. The museum contains
stone age NANDs with 256 bytes pages, as well as iron age NANDs with 512
bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig options and
already has too many of them, and there is a general kernel trend to
simplify the configuration menu.
We remove the stone age exhibits along with closing the museum
REMARK Don't apply this part from upstream:
Some of the iron age ones are transferred to the regular NAND depot.
Namely, only those which have unique device IDs are transferred, and the
ones which have conflicting device IDs are removed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit fb3bff5b407e58.
This patch enables support to read the ECC strength and size from the
NAND flash using Toshiba Memory SLC NAND extended-ID. This patch is
based on the information of the 6th ID byte of the Toshiba Memory SLC
NAND.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 3b5206f4be9b65.
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 229204da53b31d.
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 10d4e75c36f6c1.
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 9b2d61f80b060c.
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 01389b6bd2f4f7.
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit c51d0ac59f2420.
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
In preparation of moving specific nand support that are not jedec
or onfi
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
nand_get_flash_type was reworked in commit 1ca6f9483e. This change
break the Mediatek MT721. Fix it adjust the function call parameters
+include/linux/mtd/rawnand.h:32:62: note: expected 'struct nand_chip *' but argument is of type 'struct mtd_info *'
+ 32 | struct nand_flash_dev *nand_get_flash_type(struct nand_chip *chip,
+ | ~~~~~~~~~~~~~~~~~~^~~~
+drivers/mtd/nand/raw/mt7621_nand.c:1189:48: error: passing argument 2 of 'nand_get_flash_type' from incompatible pointer type [-Werror=incompatible-pointer-types]
+ | ^~~~
+ | |
+ | struct nand_chip *
+include/linux/mtd/rawnand.h:33:49: note: expected 'int *' but argument is of type 'struct nand_chip *'
+ 33 | int *maf_id, int *dev_id,
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
chip points to mtd. Passing chip is enough to have a reference
to mtd when is necessary
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit abbe26d144ec22.
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 7f501f0a72036d.
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Upstream linux commit 29a198a1592d83.
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
SPL on mvebu loads proper U-Boot from custom Marvell kwbimage format and
therefore support for other binary formats is not required to be present in
SPL. Boot source of proper U-Boot is defined by compile time options and
therefore it is not required to enable all possible and unused peripherals
in SPL by default.
This change decrease size of SPL binaries.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for hardware watchdog timer for Amlogic SoCs.
This driver has been heavily inspired by his Linux equivalent
(meson_gxbb_wdt.c).
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Philippe Boos <pboos@baylibre.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for the Marvell Octeon watchdog driver, which
currently only support the ARM64 Octeon TX & TX2 platforms. Since the
IP is pretty similar, it makes sense to extend this driver to also
support the MIPS Octeon SoC.
A follow-up patch will enable this watchdog support on the EBB7304
eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
i2c changes for 2022.10
- new driver nuvoton, NPCM7xx from Jim Liu
Fixes:
- ast_i2c: Remove SCL direct drive mode
from Eddie James
- avoid dynamic stack use in dm_i2c_write
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
patch from Rasmus Villemoes
To quote Andre:
One prominent feature is the restructering of the clock driver, which
allows to end up with one actual driver for all variants, although we
still only compile in support for one SoC.
Also contained are some initial SPI fixes, which should fix some
problems, and enable SPI flash support for the F1C100s SoC. Those
patches revealed more problems, I will queue fixes later on, but for
now it should at least still work.
Apart from some smaller fixes (for instance for NAND operation), there
is also preparation for the upcoming Allwinner D1 support, in form of
the USB PHY driver. There are more driver support patches to come.
The gitlab CI completed successfully, including the build test for all
160 sunxi boards. I also boot tested on a few boards, but didn't have
time for more elaborate tests this time.
The size of the dynamic stack allocation here is bounded by the if()
statement. However, just allocating the maximum size up-front and
doing malloc() if necessary avoids code duplication (the
i2c_setup_offset() until the invocation of ->xfer), and generates much
better (smaller) code:
bloat-o-meter drivers/i2c/i2c-uclass.o.{0,1}
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-144 (-144)
Function old new delta
dm_i2c_write 552 408 -144
Total: Before=3828, After=3684, chg -3.76%
It also makes static analysis of maximum stack usage (using the .su
files that are automatically generated during build) easier if there
are no lines saying "dynamic".
[This is not entirely equivalent to the existing code; this now uses
the stack for len <= 64 rather than len <= 63, but that seems like a
more natural limit.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Heiko Schocher <hs@denx.de>
SCL direct drive mode prevents communication with devices that
do clock stretching, so disable. The Linux driver doesn't use
this mode, and the engine can handle clock stretching.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: ryan_chen <ryan_chen@aspeedtech.com>
D1 has a register layout like A100 and H616, with the moved SIDDQ bit.
Unlike H616 it does not have any dependencies between PHY instances.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As Icenowy pointed out, newer manuals (starting with H6) actually
document the register block at offset 0x800 as "HCI controller and PHY
interface", also describe the bits in our "PMU_UNK1" register.
Let's put proper names to those "unknown" variables and symbols.
While we are at it, generalise the existing code by allowing a bitmap
of bits to clear and set, to cover newer SoCs: The A100 and H616 use a
different bit for the SIDDQ control.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since commit 089ffd0aed ("phy: sun4i-usb: Use CLK and RESET support")
neither of these headers is used. Dropping them allows the driver to be
architecture-independent.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This option is used only by the phy-sun4i-usb driver, which does not
inherently depend on the ARM architecture.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There was no user of this callback after 5b66fdb29d anymore, and its
semantic as now inconsistent between stm and sst26. What we need for the
upcoming new usecase is a "completely unlocked" semantic. So consolidate
over this.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Power-on-Reset is a method to restore flash back to 1S-1S-1S mode from 8D-8D-8D
in the begging of probe.
Command extension type is not standardized across flash vendors in DTR mode.
For suiting different vendor flash devices, adding a flag to seperate types for
soft reset on boot.
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Follow patch <f6adec1af4b2f5d3012480c6cdce7743b74a6156> (Allow using Micron mt35xu512aba
in Octal DTR mode).
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency for adding Macronix flash in Octal DTR mode.
-https://www.mxic.com.tw/Lists/Datasheet/Attachments/7841/MX25LM51245G,%203V,%20512Mb,%20v1.1.pdf
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The sunxi nand SPL loader was broken at least for SUN4I,
SUN5I and SUN7I SOCs since the implementation change
from DMA to PIO usage - commit 6ddbb1e.
Root cause for this issue is the NFC control flag NFC_CTL_RAM_METHOD
being set by method nand_apply_config.
This flag controls the bus being used for the NFCs internal RAM access.
It must be set for the DMA use case only.
See A33_Nand_Flash_Controller_Specification.pdf page 12.
This fix is tested by myself on a Cubietruck A20 board.
Others should test it on new generation SOCs as well.
Signed-off-by: Markus Hoffrogge <mhoffrogge@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The SPI controllers in the Allwinner F1Cx00 series of SoCs are
compatible to the H3 IP. The only difference in the integration is
the missing mod clock in the F1C100, instead the SPI clock is directly
derived from the AHB clock.
We *should* be able to model this through the DT, but the addition of
get_rate() requires quite some refactoring, so it's not really worth in
this simple case: We programmed both the PLL_PERIPH to 600 MHz and the
PLL/AHB divider to 3 in the SPL, so we know the SPI base clock is 200
MHz. Since we used a hard coded fixed clock rate of 24 MHz for all the
other SoCs so far, we can as well do the same for the F1C100.
Define the SPI input clock and maximum frequency differently when
compiling for the F1C100 SoC.
Also adjust the power-of-2 divider programming, because that uses a
"minus one" encoding, compared to the other SoCs.
This allows to enable SPI flash support for the F1C100 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The current SPI clock divider calculation has two problems:
- We use a normal round-down division, which results in a divider
typically being too small, resulting in a too high frequency on the bus.
- The calculaction for the power-of-two divider is very inaccurate, and
again rounds down, which might lead to wild bus frequencies.
This wasn't a real problem so far, since most chips can handle slightly
higher bus frequencies just fine. Also the actual speed was mostly lost
anyway, due to release_bus() reseting the device. And the power-of-2
calculation was probably never used, because it only applies to
frequencies below 47 KHz.
However this will become a problem for the F1C100s support, due to its
much higher base frequency.
Calculate a safe divider correctly (using round-up), and re-use that
value when calculating the power-of-2 value. We also separate the
maximum frequency and the input clock on the way, since they will be
different for the F1C100s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As George rightfully pointed out [1], the spi-sunxi driver programs the
speed and mode settings only when the respective functions are called,
but this gets lost over a call to release_bus(). That asserts the
reset line, thus forces each SPI register back to its default value.
Adding to that, trying to program SPI_CCR and SPI_TCR might be pointless
in the first place, when the reset line is still asserted (before
claim_bus()), so those setting won't apply most of the time. In reality
I see two nested claim_bus() calls for the first use, so settings between
the two would work (for instance for the initial "sf probe"). However
later on the speed setting is not programmed into the hardware anymore.
So far we get away with that default frequency, because that is a rather
tame 24 MHz, which most SPI flash chips can handle just fine.
Move the actual register programming into a separate function, and use
.set_speed and .set_mode just to set the variables in our priv structure.
Then we only call this new function in claim_bus(), when we are sure
that register accesses actually work and are preserved.
[1] https://lore.kernel.org/u-boot/20210725231636.879913-17-me@yifangu.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: George Hilliard <thirtythreeforty@gmail.com>
The current detection of RX FIFO depth seems to be not reliable, and
XCH will self-clear when a transfer is done.
Check XCH bit when polling for transfer finish.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This header is not used since commit abdbefba2a ("net: sun8i_emac: Use
consistent clock bitfield definitions"). Dropping it allows the driver
to be architecture-independent.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This just prints the PHY mode taken from the devicetree. It does not
need to be printed during every boot, and also avoids an unwanted
line break for the "net: " reporting line.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The clock and reset drivers use the exact same platform data. Simplify
them by sharing the object. This is safe because the parent device
(the clock device) always gets its driver model callbacks run first.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The reason here is the same as the reason for changing the clock driver:
platform data can be provided when binding the driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
All of the driver private data should really be platform data since it
is determined statically (selected by the compatible string or extracted
from the devicetree). Move everything to platform data, so it can be
provided when binding the driver. This is useful for SPL, or for
instantiating the driver as part of an MFD.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that all of the variants use the same bind/probe functions and ops,
there is no need to have a separate driver for each variant. Since most
SoCs contain two variants (the main CCU and PRCM CCU), this saves a bit
of firmware size and RAM.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This allows all of the clock drivers to use a common bind function.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Because the gate arrays are not given explicit sizes, the arrays are
only as large as the highest-numbered gate described in the driver.
However, only a subset of the CCU clocks are needed by U-Boot. So there
are valid clock specifiers with indexes greater than the size of the
arrays. Referencing any of these clocks causes out-of-bounds access.
Fix this by checking the identifier against the size of the array.
Fixes: 0d47bc7056 ("clk: Add Allwinner A64 CLK driver")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The reset array size is currently used for bounds checking in the reset
driver. The same bounds check should really be done in the clock driver.
Currently, the array size is provided to the reset driver separately
from the CCU descriptor, which is a bit strange. Let's do this the usual
way, with the array sizes next to the arrays themselves.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: add F1C100s support]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that the PHY driver will not try to drive VBUS if it is already
driven by an external supply, there is no need to check the VBUS voltage
before powering on the PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
This patch adds NAND flash controller driver for MediaTek MT7621 SoC.
The NAND flash controller of MT7621 supports only SLC NAND flashes.
It supports 4~12 bits correction with maximum 4KB page size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds GMAC support for MediaTek MT7621 SoC.
MT7621 has the same GMAC/Switch configuration as MT7623.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The address returned by regmap_get_range() is not remapped. Directly r/w
to this address is ok for ARM platforms since it's idential to the virtual
address.
But for MIPS platform only virtual address should be used for access.
To solve this issue, the regmap api regmap_read/regmap_write should be used
since they will remap address before accessing.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The iobase address from dts node is actually physical address. It's
identical to the virtual address in ARM platform. This is ok because this
driver was used only by ARM platforms (mt7622/mt7623 ...).
But now this driver will be used by mt7621 which is a MIPS SoC. For MIPS
platform the physical address space is mapped to KSEG0 and KSEG1 and this
makes the virtual address apparently not idential to its physical address.
To solve this issue, this patch replaces dev_read_addr with dev_remap_addr
to get the remapped iobase address.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch makes mt7621_wdt driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch makes mt7621_gpio driver available for MediaTek MT7621 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for MediaTek MT7621 SoC.
The MT7621 SoC supports pinconf, but it is not the same as mt7628.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7621 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
ISP1760/61/63 are a family of usb controllers, here the main
goal is to support the ISP1763 hcd part found in the MPS3 FPGA
board form Arm. This is based on the kernel driver and ported
to u-boot.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Move urb code from musb only use to a more common scope, so other
drivers in the future can use the handling of urb in usb.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
When usb PHY initialization is done, the PHY need to be reset.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
New IP adds a conditional reset that impact the clock
error management. It is now linked to a new compatible.
Signed-off-by: Lionel Debieve <lionel.debieve@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The stm32mp13 soc differs from the stm32mp15 in terms of
clear register offset for controlling the FMP (Fast Mode Plus).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
