Add the USB PHY driver for i.MX8MQ to work with DWC3 USB controller.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se>
The AB8500 PMIC contains an USB PHY that needs to be set up in
device or host mode to make USB work properly. Add a simple driver
for the generic PHY uclass that allows enabling it.
The if (CONFIG_IS_ENABLED(USB_MUSB_HOST)) might be a bit strange.
The USB PHY must be configured in either host or device mode and
somehow the USB PHY driver must be made aware of the mode.
Actually, the MUSB driver used together with this PHY does not
support dynamic selection of host/device mode in U-Boot at the moment.
Therefore, one very simple approach that works fine is to select
the mode to configure at compile time. When the MUSB driver is
configured in host mode the PHY is configured in host mode, and
similarly when the MUSB driver is configured in device/gadget mode.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).
The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.
Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.
This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add additional step which enables the Impedance and PLL calibration.
- Enable old squelch detector instead of the new analog squelch detector
circuit and update host disconnect threshold value.
- Update LS TX driver strength coarse and fine adjustment values.
Change-Id: Ifa0a585bfb5ecab0bfa033eed6874ff98b16a7df
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
According to Design Reference Specification the PHY PLL and Calibration
register from PHY0 are shared for multi-port PHY. PLL control registers
inside other PHY channels are not used.
This commit reworks utmi device tree nodes in a way that common PHY PLL
registers are moved to main utmi node. Accordingly both child nodes
utmi-unit range is reduced and register offsets in utmi_phy.h are updated
to this change.
This fixes issues in scenarios when only utmi port1 was in use, which
resulted with lack of correct pll initialization.
Change-Id: Icc520dfa719f43a09493ab31f671efbe88872097
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
New products can contain up to 6 usb ports, therefore allow to initialize
all relevant UTMI PHYs.
Change-Id: I28c36e59fa0e3e338bb3ee0cee2240b923f39785
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
It helps ATF to determine who called power off
function (U-boot/Linux) and act accordingly
Change-Id: Icfc5cbfdba64754496812154272b28c0ff639f0f
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
- the default value of comphy pipe selector is set to PCIe (x4)
in case of unconnected comphy the default value remains 0x4
which may lead to several issues with comphy initialization.
- this patch adds SMC call that powers off the comphy lane in case of
unconnected comphy.
Change-Id: I196b2916518dd8df3b159ffa85e2989b8e483087
Signed-off-by: Christine Gharzuzi <chrisg@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Currently, we don't pass id for SGMII 0/1.
A bug in comphy selector configuration was found (in comphy
firmware), after fixing it, SGMII0/1 have different configuration,
so we need to pass the ID the firmware.
Change-Id: Idcff4029cc9cf018278e493221b64b33574e0d38
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Change-Id: I358792a96c13b54e700c05227cc7a8f6bd584694
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Now the comphy configuration is handled in atf, therefore there is no
need to configure phy or pipe selector in u-boot, it is configured by
atf for each particular pair: lane and mode.
Change-Id: I0bebf8d5ff66dbeb6bf9ef90876195938a8eb705
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the XFI training with appropriate SMC call, so the firmware will
perform exact initialization.
Update Stefan 2021-03-23:
Move comphy_smc() function to an earlier place - necessary for the
mainline merge.
Change-Id: I789b130b05529dc80dadcf66aef407d93595b762
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Igal Liberman <igall@marvell.com>
Replace the comphy initialization for USB with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: I7f773c0dfac70db9dd2653de2cdcfac577e78c4e
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Replace the comphy initialization for RXAUI with appropriate SMC call,
so the firmware will execute required serdes configuration.
Change-Id: Iedae0285fb283e05bb263a8b4ce46e8e7451a309
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
This allows the lower level driver access to comphy map data
(required for RX training support, which is introduced
in the following patches).
Change-Id: Ib7ffdc4b32076c01c3a5d33f59552c9dfc6b12fa
Signed-off-by: Igal Liberman <igall@marvell.com>
If fdtdec_get_int can't find speed, set COMPHY_SPEED_INVALID
If fdtdec_get_int can't find type, set COMPHY_TYPE_INVALID
Move the error print if phy-type is invalid
Add continue to the probe loop (in a case of invalid phy)
Cosmetic changes
Change-Id: I0c61b40bfe685437426fe907942ed338b7845378
Signed-off-by: Igal Liberman <igall@marvell.com>
Add UTMI analog parameters initialization values according to
latest ETP.
Change-Id: I5bcca205a3995202a18ff126f371a81f69e205c8
Signed-off-by: Igal Liberman <igall@marvell.com>
UTMI should be initialized only for enabled device tree nodes.
This fix overrides current internal configuration array
entry with the next DT entry data if error is detected
during the current DT entry parsing or the current port
is disabled.
This way the internal configuration structure will only
contain valid ports information obtained from the DT.
Change-Id: I9c43c6a5d234e15ae9005d1c9bc983fc1f3544b8
Signed-off-by: Omri Itach <omrii@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
In get_speed_string() we have an array (speed_strings[])
which includes all possible speed strings.
This array size and content must be aligned to the speed
defines in comphy_data.h.
This patch adds missing 5.125G speed, aligns speed_strings[]
and fixes incorrect printing when speed > 5.0G.
Change-Id: I9900d23595094be321be0c62fcaa88036324568e
Signed-off-by: Igal Liberman <igall@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
The USB no-op PHY uses "usb-nop-xceiv" compatible string. This driver is
compatible with USB no-op PHY, so add the compatible string.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and
MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission
and Analog part of the PCIe lines.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI
panels.
This D-PHY depends on a separate analog PHY.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the PHY configure op callback to the generic PHY uclass to permit
configuring the PHY.
It's useful for MIPI DSI PHYs to setup the link timings.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
These helpers and header are taken from Linux commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Rockchip dwc based PCIe controller driver for rk356x platform.
Driver support Gen3 by operating as a Root complex.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add the Rockchip Synopsys based PCIe 3.0 PHY driver as
part of Generic PHY framework.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Change pr_debug to log_debug or dev_dbg macro and define LOG_CATEGORY.
Remove the "%s:" __func__ header as it is managed by dev macro
(dev->name is displayed) or log macro (CONFIG_LOGF_FUNC).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch adds support for optional vbus regulator.
It is managed on phy_power_on/off calls and may be needed for host mode.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
It helps ATF to determine who called power on function (U-boot/Linux).
The corresponding ATF code was added in this commit:
mvebu: cp110: avoid pcie power on/off sequence when called from Linux
55df84f974
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace the comphy initialization for PCIe with appropriate SMC call, so
the firmware will perform appropriate comphy initialization.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Replace all comphy initialization with appropriate smc calls. It will
result with triggering synchronous exception that is handled by Secure
Monitor code in EL3. Then the Secure Monitor code will dispatch each smc
call (by parsing the smc function identifier) and triggers appropriate
comphy initialization.
This patch reworks serdes handling for: SATA, SGMII, HS-SGMII and SFI
interfaces.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
- Minor cleanup on K3 env variables
- Fix OSPI compatible for J721e
- Drop unused property in omap-usb2-phy
- Update Maintainer for am335x-guardian board.
"ti,dis-chg-det-quirk" property is not part of Linux kernel DT binding
documentation. Therefore drop this and instead use soc_device_match()
to distinguish b/w AM654 SR1.0 and SR2.0 devices similar to Linux kernel
driver.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The cell_count argument is required when cells_name is NULL.
This patch adds this parameter in live tree API
- of_count_phandle_with_args
- ofnode_count_phandle_with_args
- dev_count_phandle_with_args
This parameter solves issue when these API is used to count
the number of element of a cell without cell name. This parameter
allow to force the size cell.
For example:
count = dev_count_phandle_with_args(dev, "array", NULL, 3);
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for stingray PAXB PHY controller driver.
This driver supports maximum 8 PAXB phys using pipemux data.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use the phy's device.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
`phy` doesn't exist; we need to use `x` instead.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Get the device from phy, or pass the phy in.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a driver to setup the USB PHY-s on Qualcomm IPQ40xx series SoCs.
The driver sets up HS and SS phys.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
make the shared reg optional when version is v1 for sata
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Add driver data to existing compatible string "sandbox,phy".
Add an additional compatible string without driver_data
This will verify that bind command parses, finds and passes the
correct driver data to device_bind_with_driver_data() by using
driver_data in the second sandbox_phy_ids table entry.
In sandbox_phy_bind() a check is added to validate driver_data
content.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add support for PHY_TYPE_SATA to Mediateks TPHY driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while disabling vdd supply. This way the driver doesn't see an error
when disabling an always-on regulator.
This patch is needed since the commit f93fab3126 ("Revert 'power:
regulator: Return success on attempt to disable an always-on regulator'")
and use the API introduced by commit cc4a224af2 ("power: regulator:
Introduce regulator_set_enable_if_allowed api").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the Rockchip PCIe PHY driver as part of
Generic PHY framework.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
AM654x PG1.0 has a silicon bug that D+ is pulled high after POR, which
could cause enumeration failure with some USB hubs. Disabling the
USB2_PHY Charger Detect function will put D+ into the normal state.
Using property "ti,dis-chg-det-quirk" in the DT usb2-phy node to
enable this workaround for AM654x PG1.0.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Add USB TYPEC PHY driver for rockchip platform.
Referenced from Linux TypeC PHY driver, currently
supporting usb3-port and dp-port need to add it
in the future.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add Rockchip USB2PHY driver with initial support.
This will help to use it for EHCI controller in host
mode, and USB 3.0 controller in otg mode.
More functionality like charge, vbus detection will
add it in future changes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
It is possible that users of generic_phy_*() APIs may pass a valid
struct phy pointer but phy->dev can be NULL, leading to NULL pointer
deference in phy_dev_ops().
So call generic_phy_valid() to verify that phy and phy->dev are both
valid.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Clients that are requesting some of uclass API's
without a device (with ofnode) usually have _nodev
naming convention.
- clk_get_by_index_nodev
- clk_get_by_name_nodev
- reset_get_by_index_nodev
- gpio_request_by_name_nodev
So, update the same naming convention PHY framework.
This doesn't change the existing functionality.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Usually the digital and analog phys use the same reference clock,
but some platforms have two separate reference clocks for each of
them, so add another optional clock to support them.
In order to keep the clock names consistent with PHY IP's, change
the da_ref for analog phy and ref clock for digital phy.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
The new version removes all shared banks between multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Support USB2 and USB3 PHY with shared banks when support multi-phys
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a "bulk" API to the phy API in order to
get/init/exit/power on/off a group of phys associated
with a device.
The bulk API will avoid adding a copy of the same code to
manage a group of phys in drivers.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This adds support for the USB PHY found on Amlogic GXBB SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add generic_phy_get_by_node() to get a PHY phandle from a node instead
of a udevice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[narmstrong: fixed by including ofnode.h in generic-phy.h]
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
AM654 SoC has USB2 PHY which is similar to existing USB2 PHYs on OMAP
SoCs. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Below warning is seen when this driver is built for devices with 64 bit
physical address space.
drivers/phy/omap-usb2-phy.c: In function ‘omap_usb2_phy_probe’:
drivers/phy/omap-usb2-phy.c:187:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
priv->phy_base = (void *)base;
^
Fix this by using dev_read_addr_ptr() instead of dev_read_addr().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If make the ref clock optional, no need refer to fixed-clock when
the ref clock is always on or comes from oscillator directly.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
No need check -ENOSYS anymore after add dummy_enable() for
fixed-clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
As per "Table 26-7. SATA PHY Subsystem Low-Level Programming Sequence"
in TRM [1] we need to turn on SATA_PHY_TX before SATA_PHY_RX.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
For increased DPLL stability use the settings recommended in
the TRM [1] for PHY_RX registers for SATA and USB.
For SATA we need to use spread spectrum settings even
though we don't have spread spectrum enabled. The
suggested non-spread spectrum settings don't work.
[1] DRA75x, DRA74x TRM - http://www.ti.com/lit/ug/sprui30f/sprui30f.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
Introduce a mode property in the driver data so that
we don't have to keep using "of_device_is_compatible()"
throughtout the driver.
No functional change.
Signed-off-by: Roger Quadros <rogerq@ti.com>
The AM572x Technical Reference Manual, SPRUHZ6H,
Revised November 2016 [1], shows recommended settings for the
SATA DPLL in Table 26-8. DPLL CLKDCOLDO Recommended Settings.
Use those settings in the driver. The TRM does not show
a value for 20MHz SYS_CLK so we use something close to the
26MHz setting.
[1] - http://www.ti.com/lit/ug/spruhz6h/spruhz6h.pdf
Signed-off-by: Roger Quadros <rogerq@ti.com>
For some controllers PHYs can be optional. Handling NULL pointers without
crashing nor failing, makes it easy to handle optional PHYs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----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=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
There is no proper power domain support for the keystone platforms.
However we need to turn off the USB domains before jumping to linux or it
fail to boot (observed with k2e and k2l platforms).
This can be done in the PHY driver as it is dedicated only to the keystone
platforms and matches the required on/off sequence.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The driver provides PHY for USB2, USB3.0, PCIe and SATA, and now
we just enable PCIe. As for the other functionalities will be
added gradually in upcoming days.
This is adapted from the Linux version.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Several options are presenting themselves on a various boards
where the options are clearly not used. (ie, SPL/TPL options
when SPL or TPL are not defined)
This patch is not attempting to be a complete list of items, but
more like low hanging fruit. In some instances, I wasn't sure
of DM was required, so I simply made them SPL or TPL.
This patch attempts to reduce some of the menuconfig noise
by defining dependencies so they don't appear when not used.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 can be added later.
SERDES in am654x has three input clocks (left input, external
reference clock and right input) and two output clocks (left
output and right output) in addition to a PLL mux clock which
the SERDES uses for Clock Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input
clocks. The right output can select between left input and
external reference clock while the left output can select
between the right input and external reference clock.
The driver has support to select PLL mux and left/right output
mux as specified in device tree.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
In preparation for supporting the musb driver, this patch
adds support for the usb phy associated with the musb driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USB PHY used in the Allwinner H6 SoC has some pecularities (as usual),
which require a small addition to the USB PHY driver:
In this case the second PHY is PHY3, not PHY1, so we need to skip number
1 and 2 in the code. Just use the respective code from Linux for that.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.
The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This driver is derived from this Linux driver:
linux/drivers/phy/ralink/phy-ralink-usb.c
The driver sets up power and host mode, but also needs to configure PHY
registers for the MT7628 and MT7688.
I removed the reset controller handling for the USB host and device, as
it does not seem to be necessary right now. The soft reset bits for both
devices are enabled by default and testing has shown (with hackish
reset handling added), that USB related commands work identical with
or without the reset handling.
Please note that the resulting USB support is tested only very minimal.
I was able to detect one of my 3 currently available USB sticks.
Perhaps some further work is needed to fully support the EHCI controller
integrated in the MT76x8 SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The MESON_GXL_USB_PHY is also used on the Amlogic Meson GXM SoCs.
Fixes: 2960e27e38 ("phy: Add Amlogic Meson USB2 & USB3 Generic PHY drivers")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Now clock and reset drivers are available for respective
SoC's so use clk and reset ops on phy driver.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support to handle USB3 PHYs present on AM57xx/DRA7xx SoCs. This is
needed to move AM57xx to DM_USB.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Only H3 and H5 have 4 PHYS so restrict rst_mask only for them
by checking PHY id as 3 and update the proper bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.
Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
In case of phy are provided from a PHY provider nodes as following:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <1>;
};
};
and PHY are called as following:
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc_clk USBH>;
resets = <&rcc_rst USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
companion = <&usbh_ohci>;
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Also fix bad accents in my name.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A23 has 2 USB PHY's and 0x04 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner A33 has 2 USB PHY's and 0x10 has phy ctrl offset.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add PHY configs for Allwinner A10/A13/A20 which are SUN4I.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.
This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.
Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.
Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The DTS file for armada-37xx uses the string "marvell,armada3700-ehci",
but the code searched for "marvell,armada-3700-ehci".
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the reg_set* functions into comphy.h as static inline functions.
Change return type of get_*_string to const char *.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SGMII initialization PIN_PIPE_SEL has to be zero when resetting
the PHY. Since comphy_mux already set the selector register to
correct values, we have to store it's value before setting it to 0
and restore it after SGMII init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The register addresses on lanes 0 and 1 are switched, first comes 1 and
then 0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently comphy_mux supports only trivial order of nodes in pin
selector register, that is lane N on position N*bitcount.
Add support for nontrivial order, with map stored in device tree
property mux-lane-order.
This is needed for Armada 37xx.
As far as I know, there is no driver for Armada 37xx comphy in the
kernel. When such a driver comes, this will need to be rewritten to
support the device tree bindings from the kernel.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is based on commit d9899826 by
zachary <zhangzg@marvell.com>
from u-boot-marvell, see
github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/d9899826
- According to design specification, the transmitter should be set to high
impedence mode during electrical idle. Thus transmitter should detect RX
at high impedence mode also, and delay is needed to accommodate high
impedence off latency. Otherwise the USB3 will have detection issue that
most of the time the USB3 device can not be detected at all, or be
detected as USB2 device sometimes.
Modified registers: RD005C302h (R181h) (0051h) Lane Configuration 1
Bit 6: set to 1 to let Tx detect Rx at HiZ mode
Bit [3:4]: set to 2 to be delayed by 2 clock cycles
Bit 0: set to 1 to set transmitter to high impedance mode during idle.
- USB3 De-emphasize level of -3.5dB is mandatory, but USB3 MAC selects 0x2
(emphasize disabled) in the MAC_PHY_TXDEEMPH [1:0], while it is supposed
to select 0x1(3.5dB emphasize). Thus need to override what comes from
the MAC(by setting register 0x1c2 bit2 to 0x1) and to configure the
overridded values of MAC_PHY_TXDEEMPH [1:0] to 0x1(bit15 of register
0x181 and bit0 of register 0x180).
- According to USB3 application note, need to update below comphy
registers:
Set max speed generation to USB3.0 5Gbps(set RD005C04Ah bit[11:10] to 1)
Set capacitor value to 0xF(set RF005C224 bit[3:0] to 0xF)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
According to specification, CFG_PM_RXDLOZ_WAIT should be set to 0x7
when reference clock is at 25 MHz. The specification (at least the
version I have) does not mentoin the setting for 40 MHz reference
clock, but Marvell's U-Boot sets 0xC in that case.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When USB3 is on comphy lane 2 on the Armada 37xx, the registers
have to be accessed indirectly via SATA indirect access.
This is the case of the Turris Mox board from CZ.NIC.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Create a special function for indirect register setting,
reg_set_indirect, and use it instead of the two calls to reg_set.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In U-Boot it is usually written this way.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The timeout is set to PLL_LOCK_TIMEOUT in every call to
comphy_poll_reg. Remove this parameter from the function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently there is for each register special functional macro, ie:
LANE_CFG1_ADDR(u)
GLOB_CLK_SRC_LO_ADDR(u)
...
where can be either PCIE or USB3.
Change this to one function PHY_ADDR(unit, addr). The code becomes:
phy_addr(PCIE, LANE_CFG1)
phy_addr(PCIE, GLOB_CLK_SRC_LO)
...
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro phy_write16 is not used by the rest of the code,
phy_read16 is not used at all.
We also change the macro SGMIIPHY_ADDR to a static inline function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
All the calls to reg_set and friends have to cast the first argument
to void __iomem *. Lets change the return type of the MVEBU_REG macro
instead.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merged in linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the generic phy driver for the picoPHY ports
used by USB2/1.1 controllers. It is found on STiH407 SoC
family from STMicroelectronics.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver is used to stub PHY operations in a driver (USB, SATA).
This is useful when the 'client' driver (USB, SATA, ...) uses the PHY
framework and there is no actual PHY harwdare to drive.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
phy->dev need to be set to NULL in case of generic_phy_get_by_index()
fails. Then phy->dev can be used to check if the phy is valid
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ARCH_OMAP2 has been renamed ARCH_OMAP2PLUS in commit a93fbf4a78
("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This phy is found on omap platforms with sata capabilities.
Except for the part related to the DM and the PHY framework, the code is
basically a copy paste from arch/arm/mach-omap2/pipe3-phy.c
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Those tests check:
- the ability for a phy-user to get a phy based on its name or its index
- the ability of a phy device (provider) to manage multiple ports
- the ability to perform operations on the phy (init,deinit,on,off)
- the behavior of the uclass when optional operations are not implemented
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add PCIE analog parameters initialization values according to
latest ETP.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
No functional change.
The variable name "comphy_index" is misleading, it represents
cp index and not comphy index.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add SFI analog parameters initialization values according to
latest ETP.
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
since now the COMPHY can also be ignored, we must know the
state of the COMPHY. we cannot assume anymore that a missing
COMPHY is unconnected.
Signed-off-by: Yehuda Yitschak <yehuday@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
