When k_recv() returns zero it indicates that kermit transfer was aborted.
Function do_load_serial_bin() (caller of load_serial_bin()) interprets
value ~0 as aborted transfer, so properly propagates information about
aborted transfer from k_recv() to do_load_serial_bin().
Signed-off-by: Pali Rohár <pali@kernel.org>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
All platforms define CONFIG_SYS_LOAD_ADDR, but only some define
CONFIG_LOADADDR. Very very rarely are these not the same address, and
qemu-ppce500 is one such case. However, based on reading the history of
the code, this mismatched value was simply a copy-paste from other
PowerPC platforms where it is this unused currently. Switch the code to
use CONFIG_SYS_LOAD_ADDR and update the documentation.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig. Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL. Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support. Convert all of the existing users to
one or more symbols.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
to Kconfig. We move these symbols around a bit and add appropriate
dependencies to them. In some cases, we now add a correct default value
as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
At this point in time, there's no systems with "U-Boot environment
exists on an EEPROM which is accessed over the I2C bus" that sets this
option. Drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYSilpgAKCRDKSWXLKUoM
Id2JAJ9jY19JiEpOd3vuRCT5CE/pzX4yDACeP8DiXDzSi5tLHwDWUCBobUTze2s=
=5lnj
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.10-rc3
xilinx:
- Disable CONFIG_ARCH_FIXUP_FDT_MEMORY
- Print information about cpu via soc drivers and enable DISPLAY_CPUINFO
- Wire infrastructure for DTB_RESELECT and MULTI_DTB_FIT
zynq:
- Wire single QSPI
- Use power-source instead of io-standard properties
- Enable nor on zc770-xm012
zynqmp:
- Change handling around multi_boot()
- Setup offset for u-boot.itb in spi
- Generate run time dfu_alt_info for capsule update
- Use explicit values for enums (zynqmp_firmware.h)
- Enable RTC/SHA1/BUTTON/BUTTON_GPIO command
- Disable WDT driver by default
- Bind usb/scsi via preboot because of EFI
- DT updates/fixes
- Add soc driver
- Fix SPL SPI boot mode
versal:
- Add soc driver
sdhci:
- Update tap delay programming for zynq_sdhci driver
cmd:
- Fix RTC uclass handling in date command
- Update pwm help message
- Update reset help message
watchdog:
- Fix wwdt compilation
rtc:
- Deal with seq alias in rtc uclass
- Add zynqmp RTC driver
fdt:
- Add kernel-doc for fdt_fixup_memory_banks()
The commit 573a3811ed ("sysreset: psci: support system reset in a generic
way with PSCI") has added support for warm reset via PSCI but this hasn't
been reflected in usage message and user has to look at the code how to run
it. That's why update usage text to make this clear.
Here is full help with updated usage:
ZynqMP> help reset
reset - Perform RESET of the CPU
Usage:
reset - cold boot without level specifier
reset -w - warm reset if implemented
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
The first name is taken from command name that's why shouldn't be listed in
help. And commands shouldn't be listed with <> which means value but value
itself is command name.
Also add description for commands to make it clear what it does.
Before
pwm pwm <invert> <pwm_dev_num> <channel> <polarity>
pwm <config> <pwm_dev_num> <channel> <period_ns> <duty_ns>
...
After:
pwm invert <pwm_dev_num> <channel> <polarity> - invert polarity
pwm config <pwm_dev_num> <channel> <period_ns> <duty_ns> - config PWM
pwm enable <pwm_dev_num> <channel> - enable PWM output
pwm disable <pwm_dev_num> <channel> - disable PWM output
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RTCs are using sequence number defined in aliases node. Date command with
DM_RTC enabled is looking for the first RTC with index 0. But when
RTC_EMULATION is enabled it gets likely most of the time index 0 even when
system has rtc0 device via aliases node and gets sequence number 0.
That's why extend the code to look for sequence 0 number first. If this
fails continue to use existing device with index 0.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modified the help text of 'chpart' command ,mentioning that it is
for MTD devices.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
HELP description is provided for ‘configure’ sub-command
of ‘blkcache’.
Signed-off-by: Adarsh Babu Kalepalli <opensource.kab@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fixed broken ICH SPI driver in software sequencer mode
- Added "m25p,fast-read" to SPI flash node for x86 boards
- Drop ROM_NEEDS_BLOBS and BUILD_ROM for x86 ROM builds
- Define a default TSC timer frequency for all x86 boards
- x86 MTRR MSR programming codes bug fixes
- x86 "hob" command bug fixes
- Don't program MTRR for DRAM for FSP1
- Move INIT_PHASE_END_FIRMWARE to FSP2
- Use external graphics card by default on Intel Crown Bay
- tangier: Fix DMA controller IRQ polarity in CSRT
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The resource type for system memory is currently displayed as
"unknown", which is wrong.
Fixes: 51af144eb7 ("x86: Allow showing details about a HOB entry")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
At present the hob command usage and help messages are messed up
in a single line. They should be separated.
This was a regression introduced when [seq] and [-v] were added
to the command.
Fixes: d11544dfa9 ("x86: hob: Add way to show a single hob entry")
Fixes: 51af144eb7 ("x86: Allow showing details about a HOB entry")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on chromebook_coral, chromebook_samus, chromebook_link, minnowmax
Tested-by: Simon Glass <sjg@chromium.org>
It seems useful to show whether the address of the Control or Working
devicetree is being shown. Add support for this. Drop the confusing 0x
prefix since the command itself only accepts hex.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add format string handling operator to the setexpr command.
It allows to use C or Bash like format string expressions to be
evaluated with the result being stored inside the environment variable
name.
setexpr <name> fmt <format> [value]...
The following example
setexpr foo fmt "%d, 0x%x" 0x100 ff
will result in $foo being set to "256, 0xff".
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Import the following helper functions from Busybox-1.33.1 which are
required by printf.c:
process_escape_sequence from libbb/process_escape_sequence.c,
skip_whitespace from libbb/skip_whitespace.c,
overlapping_strcpy from libbb/safe_strncpy.c
src-url: https://git.busybox.net/busybox/
commit bcc5b0e6caca6c7602a6a41f "Bump version to 1.33.1"
version: 1.33.1
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
Import printf.c from the Busybox project, which provides Bash like
format string handling.
src-url: https://git.busybox.net/busybox/
commit bcc5b0e6caca6c7602a6a41f "Bump version to 1.33.1"
version: 1.33.1
Signed-off-by: Roland Gaudig <roland.gaudig@weidmueller.com>
smc and hvc commands take upto 8 user input arguments, the maximum
number of arguments of the U_BOOT_CMD macro should set to 9.
Besides, fix the typo (arg7 -> arg6) in hvc command's help message.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As 'part_get_info_by_name' now returns more status codes than just
-1 to indicate failure, we need to update the return value check.
Signed-off-by: Anders Dellien <anders.dellien@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Allow pin name parameter for pimux staus command,
as gpio command to get status of one pin.
The possible usage of the command is:
> pinmux dev pinctrl
> pinmux status
> pinmux status -a
> pinmux status <pin-name>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the result of do_status and always returns a CMD_RET_ value
(-ENOSYS was a possible result of show_pinmux).
This patch also adds pincontrol name in error messages (dev->name)
and treats correctly the status sub command when pin-controller device is
not selected.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
In a system with multiple network controllers it can be difficult
to know the names of the various devices available. This is especially
true for USB ether devices as they do not display device names upon
detection.
This is being added as a net sub-system in case other commands may
want to be added or moved here.
Note that this is only enabled for DM_ETH
Example:
U-Boot > net
net - NET sub-system
Usage:
net list - list available devices
U-Boot > net list
eth0 : ethernet@2188000 00:d0:12:98:f5:47 active
eth1 : e1000#0 00:d0:12:98:f5:48
eth2 : asix_eth 8c:ae:4c:f5:84:9d
eth3 : asix_eth 8c:ae:4c:f9:41:e3
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Probably, a pointer to a variable in an inner block should not
be exposed to an outer block.
Fixes: c70f44817d ("efi_loader: simplify 'printenv -e'")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
[trini: Don't make guid const now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Display the number of the boot option and not its index.
Fixes: 2ecee31017 ("efi_loader: use efi_create_indexed_name()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The <name> argument can now also be MTD's DM device name or OF path.
Mention this is command help.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
This patch allows uboot scripts make choices about where to boot from based
on the active mmc boot partition. This allows having two copies of kernel,
filesystems etc, and choosing which to boot from based off of the active
bootloader partition.
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If the environment does not have "soc" or "board" set, and fdtdir
option is specified in extlinux.conf, the bootloader will crash whilst
dereferencing a null pointer. Add a guard against null soc or
board. Fixes a crash of qemu-riscv64_smode configuration, which does
not have CONFIG_SYS_SOC defined.
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support command for debugging K3 power domains. This is useful with
the HSM rearch setup, where power domains are directly controlled by SPL
instead of going through the TI SCI layer. The debugging support is only
available in the u-boot codebase though, so the raw register access
power domain layer must be enabled on u-boot side for this to work. By
default, u-boot side uses the TI SCI layer, and R5 SPL only uses the
direct access methods.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add new clk subcommand "clk setfreq", for setting up a clock rate
directly from u-boot cmdline. This is handy for any debugging purposes
towards clocks.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Some clocks are not associated to a DM node, so just parsing the DM is not
enough. This is especially true for root clocks, which typically don't have
any parents. Instead, fetch every registered UCLASS_CLK instance, and dump
these out.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Add the missing dependency for the command ums:
- CONFIG_BLK: call of blk_* functions in usb_mass_storage.c
- CONFIG_USB_GADGET: required to select CONFIG_USB_FUNCTION_MASS_STORAGE
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use efi_get_variable_int() instead of EFI_CALL(RT->get_variable()).
Use efi_set_variable_int() instead of EFI_CALL(efi_set_variable()).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Simplify the creation of indexed variable names like 'Boot0000' by using
function efi_create_indexed_name().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To print a UTF-16 string use %ls instead of converting string to UTF-8.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To print a UTF-16 string use %ls instead of converting string to UTF-8.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With better compiler optimizations available, a compiler may see we do
nothing with our buffer after calling memset and omit the call, thus
causing us to not smash the stack. Add a comment to explain why we now
also have a printf call, so that the test will pass as the memset will
not be omitted.
Reported-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rename the misleading cmd "rx_training" to "mvebu_comphy_rx_training" to
avoid confusion and mixup with DDR3/4 training. This makes it clear,
that this command is platform specific and handles the COMPHY RX
training.
Also depend this cmd on ARMADA_8K and not TARGET_MVEBU_ARMADA_8K to make
is available for OcteonTX2 CN913x.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pali Rohár <pali@kernel.org>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Acked-by: Marek Behún <marek.behun@nic.cz>
Acked-by: Pali Rohár <pali@kernel.org>
This patch adds a new "extension" command, which aims at detecting
extension boards connected to the hardware platform, and apply the
Device Tree overlays that describe the hardware present on those
extension boards.
In order to enable this mechanism, board-specific code must implement
the extension_board_scan() function that fills in a linked list of
"struct extension", each describing one extension board. In addition,
the board-specific code must select the SUPPORT_EXTENSION_SCAN Kconfig
boolean.
Based on this:
- "extension scan" makes the generic code call the board-specific
extension_board_scan() function to retrieve the list of detected
extension boards.
- "extension list" allows to list the detected extension boards.
- "extension apply <number>|all" allows to apply the Device Tree
overlay(s) corresponding to one, or all, extension boards
The latter requires two environment variables to exist and set one variable
to run:
- extension_overlay_addr: the RAM address where to load the Device
Tree overlays
- extension_overlay_cmd: the U-Boot command to load one overlay.
Indeed, the location and mechanism to load DT overlays is very setup
specific.
- extension_overlay_name: set by the command: the name of the DT which
will be load during the execution.
When calling the command described in the extension_overlay_cmd
variable, the variable extension_overlay_name will be defined. So a
typical extension_overlay_cmd will look like this:
extension_overlay_cmd=load mmc 0:1 $extension_overlay_addr /boot/$extension_overlay_name
Here is an example on how to use it:
=> run loadfdt
=> fdt addr $fdtaddr
=> setenv extension_overlay_addr 0x1000
=> setenv extension_overlay_cmd 'load mmc 0:1 ${extension_overlay_addr} /boot/${extension_overlay_name}'
=> extension scan
Found 1 extension board(s).
=> extension apply 0
519 bytes read in 3 ms (168.9 KiB/s)
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Move the fdt_valid function to fdt_support.
This changes allow to be able to test the validity of a devicetree in
other c files.
Update code syntax.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
The ebreak instruction should generate a breakpoint exception.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This change would enhance the existing 'gpt read' command to allow
(optionally) writing of the read GPT partitions to an environment
variable in the UBOOT partitions layout format. This would allow users
to easily change the overall partition settings by editing said variable
and then using the variable in the 'gpt write' and 'gpt verify' commands.
Signed-off-by: Farhan Ali <farhan.ali@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Corneliu Doban <cdoban@broadcom.com>
Cc: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for running RX training using new command called
"rx_training"
Usage:
rx_training - rx_training <cp id> <comphy id>
RX training allows to improve link quality (for SFI mode)
by running training sequence between us and the link partner,
this allows to reach better link quality then using static configuration.
Change-Id: I818fe67ccaf19a87af50d4c34a9db7d6802049a5
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
- fix the dependency for MMC boot (add XENON to MVEBU_MMC)
- fix the bubt destination assignment (missing # in "else" case)
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On systems without usb gadget dfu core fails which was reported by error
but command itself returns pass which breaks any usage in a script.
That's why propagate error from run_usb_dnl_gadget().
Fixes: 16297cfb2a ("usb: new board-specific USB init interface")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Trying to compile with CONFIG_CMD_MMC=y and CONFIG_MMC=n leads to errors:
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmcops':
cmd/mmc.c:984: undefined reference to `get_mmc_num'
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmc_setdsr':
cmd/mmc.c:873: undefined reference to `find_mmc_device'
Add missing dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In case exit is called in a script without parameter, the command
returns -2 ; in case exit is called with a numerical parameter,
the command returns -2 and lower. This leads to the following problem:
=> setenv foo 'echo bar ; exit 1' ; run foo ; echo $?
bar
0
=> setenv foo 'echo bar ; exit 0' ; run foo ; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2' ; run foo ; echo $?
bar
0
That is, no matter what the 'exit' command argument is, the return
value is always 0 and so it is not possible to use script return
value in subsequent tests.
Fix this and simplify the exit command such that if exit is called with
no argument, the command returns 0, just like 'true' in cmd/test.c. In
case the command is called with any argument that is positive integer,
the argument is set as return value.
=> setenv foo 'echo bar ; exit 1' ; run foo ; echo $?
bar
1
=> setenv foo 'echo bar ; exit 0' ; run foo ; echo $?
bar
0
=> setenv foo 'echo bar ; exit -2' ; run foo ; echo $?
bar
0
Note that this does change ABI established in 2004 , although it is
unclear whether that ABI was originally OK or not.
Fixes: c26e454dfc
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Tom Rini <trini@konsulko.com>
We move qfw into its own uclass and split the PIO functions into a
specific driver for that uclass. The PIO driver is selected in the
qemu-x86 board config (this covers x86 and x86_64).
include/qfw.h is cleaned up and documentation added.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
serial_reinit_all() is only available if CONFIG_SERIAL is defined (i.e.
!CONFIG_DM_SERIAL).
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
stdio_dev methods have taken a pointer to themselves since 709ea543
(nearly 7 years ago).
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace static function efi_get_device_handle_info() by a simplified
function efi_get_device_path_text() avoiding EFI_CALL().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
U-Boot can instantiate CAAM RNG if needed by crypto operations.
Call sec_init() prior running a blob operation to ensure
RNG is correctly instantiated.
Make sure CAAM clock is enabled and check if a job ring is
available for that operation.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In order to build CMD_BLOB on i.MX CAAM supported devices it's
necessary to select IMX_HAB. Add IMX_HAB and CAAM supported
SoCs as dependency.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to Specification, each bit have valid value.
But it doesn't check whether arguments is valid or not.
It has potential bug with arguments passed by wrong value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Modified more readable about hwpartition usage.
Because it's difficult to understand how to use its command.
The arguments didn't optional.
mmc hwpartition needs to pass <USER> <GP> <MODE> as arguments.
Description about each arguments what is required is the below:
USER - <user> <enh> <start> <cnt> <wrrel> <{on|off}>
GP - <{gp1|gp2|gp3|gp4}> <cnt> <enh> <wrrel> <{on|off}>
MODE - <{check|set|complete}>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
The usb command cannot be compiled with CONFIG_USB=n:
ld.bfd: cmd/usb.c:660: undefined reference to `usb_stop'
ld.bfd: cmd/usb.c:663: undefined reference to `usb_started'
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present when a file is bound to a host device it is always marked as
removeable. Arguably the device is removeable, since it can be unbound at
will. However while it is bound, it is not considered removable by the
user. Also it is useful to be able to model both fixed and removeable
devices for code that distinguishes them.
Add a -r flag to the 'host bind' command and plumb it through to provide
this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the 'bind' subcommand before processing the arguments. This will
make it easier to add an optional flag.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has a strange mix of declarations and argument parsing
which is a bit hard to follow and harder to modify. Separate out the
declarations at the start of the function and adjust the ordering of
the code slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
This information is interesting to look at and can be important for
debugging and inspection. Add a command to display it in a helpful
format.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is possible to boot U-Boot for chromebook_coral either 'bare metal' or
from coreboot. In the latter case we want to provide access to the coreboot
sysinfo tables. Move the definitions into a file available to any x86
board.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit enables the ESRT printing from the u-boot shell by invoking:
- efidebug capsule esrt
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Alexander Graf <agraf@csgraf.de>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviwed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The ESRT is initialised during efi_init_objlist after
efi_initialize_system_table().
The ESRT is recreated from scratch at the following events:
- successful UpdateCapsule;
- FMP instance install.
The code ensures that every ESRT entry has a unique fw_class value.
Limitations:
- The ESRT is not updated if an FMP instance is uninstalled;
- the fields image_type and flags are in the current implementation left
undefined. Setting these values will require a per-platform function
that returns the image_type/flags as a function of the image fw_class.
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Sughosh Ganu <sughosh.ganu@linaro.org>
CC: AKASHI Takahiro <takahiro.akashi@linaro.org>
CC: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CC: Andre Przywara <andre.przywara@arm.com>
CC: Alexander Graf <agraf@csgraf.de>
CC: nd@arm.com
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Remove two EFI_CALL() indirections.
Move ESRT GUID in efidebug's list of GUIDs.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI spec allows a packed array of UEFI device paths in the
FilePathList[] of an EFI_LOAD_OPTION. The first file path must
describe the loaded image but the rest are OS specific.
Previous patches parse the device path and try to use the second
member of the array as an initrd. So let's modify efidebug slightly
and install the second file described in the command line as the
initrd device path.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Up to now we install EFI_LOAD_FILE2_PROTOCOL to load an initrd
unconditionally. Although we correctly return various EFI exit codes
depending on the file status (i.e EFI_NO_MEDIA, EFI_NOT_FOUND etc), the
kernel loader, only falls back to the cmdline interpreted initrd if the
protocol is not installed.
This creates a problem for EFI installers, since they won't be able to
load their own initrd and continue the installation. It also makes the
feature hard to use, since we can either have a single initrd or we have
to recompile u-boot if the filename changes.
So let's introduce a different logic that will decouple the initrd
path from the config option we currently have.
When defining a UEFI BootXXXX we can use the filepathlist and store
a file path pointing to our initrd. Specifically the EFI spec describes:
"The first element of the array is a device path that describes the device
and location of the Image for this load option. Other device paths may
optionally exist in the FilePathList, but their usage is OSV specific"
When the EFI application is launched through the bootmgr, we'll try to
interpret the extra device path. If that points to a file that exists on
our disk, we'll now install the load_file2 and the efi-stub will be able
to use it.
This opens up another path using U-Boot and defines a new boot flow.
A user will be able to control the kernel/initrd pairs without explicit
cmdline args or GRUB.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we have to call
efi_set_bootdev() or we won't be able to execute it.
Put the includes into alphabetic order.
Fixes: 5f59518a7b ("efi_loader: setting boot device")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This occur when building on Raspberry Pi 400 (32-bit ARM). Fix them.
Examples:
cmd/efidebug.c: In function ‘do_efi_capsule_update’:
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:9: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:19: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
In file included from include/common.h:20,
from lib/efi_loader/efi_capsule.c:9:
lib/efi_loader/efi_capsule.c: In function ‘efi_update_capsule’:
include/efi_loader.h:83:8: warning: format ‘%lu’ expects argument of type
‘long unsigned int’, but argument 10 has type ‘size_t’
{aka ‘unsigned int’} [-Wformat=]
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:229:2: note: in expansion of macro ‘log’
log(LOG_CATEGORY, LOGL_DEBUG, fmt, ##args); \
^~~
include/log.h:249:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
include/efi_loader.h:83:2: note: in expansion of macro ‘debug’
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~
lib/efi_loader/efi_capsule.c:444:2: note: in expansion of macro ‘EFI_ENTRY’
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
^~~~~~~~~
lib/efi_loader/efi_capsule.c:444:19: note: format string is defined here
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
~~^
%u
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace (uintptr_t)NULL by 0.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When uploading an EFI binary via the UART we have to call
efi_set_bootdev() or we won't be able to execute it.
Put the includes into alphabetic order.
Fixes: 5f59518a7b ("efi_loader: setting boot device")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This occur when building on Raspberry Pi 400 (32-bit ARM). Fix them.
Examples:
cmd/efidebug.c: In function ‘do_efi_capsule_update’:
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:9: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
cmd/efidebug.c:75:49: warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
ret = EFI_CALL(RT->update_capsule(&capsule, 1, (u64)NULL));
^
include/efi_loader.h:104:19: note: in definition of macro ‘EFI_CALL’
typeof(exp) _r = exp; \
^~~
In file included from include/common.h:20,
from lib/efi_loader/efi_capsule.c:9:
lib/efi_loader/efi_capsule.c: In function ‘efi_update_capsule’:
include/efi_loader.h:83:8: warning: format ‘%lu’ expects argument of type
‘long unsigned int’, but argument 10 has type ‘size_t’
{aka ‘unsigned int’} [-Wformat=]
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~~~~~~~~~~~~~~
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:229:2: note: in expansion of macro ‘log’
log(LOG_CATEGORY, LOGL_DEBUG, fmt, ##args); \
^~~
include/log.h:249:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
include/efi_loader.h:83:2: note: in expansion of macro ‘debug’
debug("%sEFI: Entry %s(" format ")\n", __efi_nesting_inc(), \
^~~~~
lib/efi_loader/efi_capsule.c:444:2: note: in expansion of macro ‘EFI_ENTRY’
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
^~~~~~~~~
lib/efi_loader/efi_capsule.c:444:19: note: format string is defined here
EFI_ENTRY("%p, %lu, %llu\n", capsule_header_array, capsule_count,
~~^
%u
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace (uintptr_t)NULL by 0.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable and provision the SCP03 keys on a TEE controlled secured elemt
from the U-Boot shell.
Executing this command will generate and program new SCP03 encryption
keys on the secure element NVM.
Depending on the TEE implementation, the keys would then be stored in
some persistent storage or better derived from some platform secret
(so they can't be lost).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
We don't need to enable logging to run this command since the output will
still appear. Drop the 'select'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'virtio' command calls blk_common_cmd() which is only available
when CONFIG_HAVE_BLOCK_DEVICE is on. Fix the Kconfig dependency.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This adds a new command 'addrmap' to display the address map for
non-identity virtual-physical memory mappings.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Take over the plain 'tpm_...' functions for use by the new TPM API. Rename
all the TPMv1 functions so they are called from the API.
Update the TPMv1 functions so that they are called from the API. Change
existing users to use the tpm1_ prefix so they don't need to go through
the API, which might introduce uncertainty.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds an option to part_get_info_by_dev_and_name_or_num to allow
callers to specify whether whole-disk partitions are fine.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sf test command is used to test spi flashes (and spi masters). Printing
the exact error code is very helpful to those debugging the spi stack.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If there is an error while erasing SPI flash, no errno is displayed. This
makes it difficult to determine the cause of the error. This change mirrors
the logic for write errors above.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Let the sbi command detect the 'System Reset Extension'
(EID #0x53525354 "SRST").
Cf. https://github.com/riscv/riscv-sbi-doc
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Reviewed-by: Leo Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
The pinmux command uses functions pinctrl_get_pin_*(), which are missing
if PINCTRL config option is disabled.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, we check argc in a number of places to make sure that we have
all of the required arguments for each of the pwm sub-commands.
However, there's at least one place where we've got dead code as we'll
never have argc == 0, due to checking that argc was at least 4 earlier
and having only subtracted 3. Rework things so that when we have
determined our subcommand make sure we have the right number of
arguments for it, or error out. This means we can stop checking against
argc again later.
Reported-by: Coverity (CID: 316601)
Cc: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It's confusing whether arguments are optional or mandatory.
Update the command's usage to clarify how to use.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmAcTmoACgkQxIHbvCwF
GsT0ag/6AjtRtGd8ySYix9lytmDphyztvTTHrd/Bz+UWi64iEIOH6t/RIAPG0yb0
WJBvTe9eGxbNx5VOx426YtPUGFfzAakMyRaAL5Y4wkQsKgseq3q2sE55wzG4nTiR
nmweR7TPslSkGtqQQehGGtdMJn//M/alABtTQs5eyjOkJPEc4DzATeksfA64t2Dj
ijaU4dWbKVHy8spz3xH9cIdF1fvCJGxvSvXCVculN5bfgCf/MJYq6gb2VgXyLL1w
+6GNklzNKRY8Lk9C4hqq2ktK4dQ4R0qKgqxtihwuSdbZmhV6cScKvmNPCqdYx/1l
p5ywE067KRm16Hl/41QhKPMVleqn33Td3U4I+CWvO9DPnsH7pY9iRymM6zfRm9+j
nO4f8++OqG/YXL+oABLkSIZaoYWqGmZd5Nc1bq9sTXthUXHZeC6/V19n0TJYVIV5
HtIPFJbqn4S4uKjTFxyvudE6OfeW4+HpsY7bQHDRXWY1Kma0fgMYbhFZdUeNyr+6
N8EFXZ5nKVWqLH9zlAIPOn0AEXzOfvsWad+NU0bILY8f60SqW0AydjvzG8z9CU3e
vqxx+NxcG26SYscIcANvMI7HxtB6mblBYF2vSqBAkSrQ23Om+dnKkLhHO8pkkNtn
J4rLpAxEAA1yaqKK/1n67D6pSqvjdWQqOfgL/3E1sqgAGYYOBrc=
=rQaL
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-04-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-04-rc2
Bug fixes:
* do not allow creating of files with filenames on FAT file system
* install UEFI System Partition GUID on ESP handle
* in dtbdump.efi test tool use GUID to find ESP handle
Documentation:
* man-page for load command
* describe end of life of plat_auto
On the handle for the UEFI System Partition we must install the System
Partition GUID (with a NULL interface).
Let the efidebug command display the GUID.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow booting a 32-bit system with a top memory address beyond 4 GiB
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAbVFARHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebn/Af9FoJksV/0G+z6AzjJ20+yoOVAOFFhUkFB
UTW5m0Sv3wMmlSNdg0+DPuB3o04U6RwlZTdIqK/shc0fEqr0YeJgWAEPSMjQH0xc
ou8S9LAnJNrvlqNu5aP2Wq5KFwOxp/ODx5RBNpiSaL+m26dmUi2eeU+Ym996rr06
+m0qycZP07BHLIfm0pWyZjAI2+VzR7Uuyd1pKEIerOTRkAvZzk6pQbs+vv6PLaHa
Wcl9grnoO3pDZt6CYpmgv8mbetXteRfrdYMsu2OiHx/2nU3pa7TbOoNcuA2ww2Ko
u9NL7s0E0Y1LY6/QNb1O7eGOxcR1H5y/19K6NGrK27BwMkrvb0GKRg==
=jMvm
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-3feb21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
Support late device removal
Allow booting a 32-bit system with a top memory address beyond 4 GiB
Add "zboot" command to the list of supported boot in the
label_boot function.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add component tags in the summary]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Replace all the macro ifdef by IS_ENABLED.
All of these configs are set in the defconfig files and not in the
include board headers files.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: keep the preprocessor case unchanged]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are some calls to bdinfo_print_num_l() with parameters that
could be a 64-bit value on a 32-bit system. Change those calls to
use bdinfo_print_num_ll() instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present we have bdinfo_print_num() to print unsigned long numbers.
We also have print_phys_addr() which accept numbers that might be
64-bit on a 32-bit platform.
Rename these 2 functions to be clearer:
bdinfo_print_num() => bdinfo_print_num_l()
print_phys_addr() => bdinfo_print_num_ll()
While we are here, make bdinfo_print_num_ll() public so that it can
be used outside cmd/bdinfo.c in the future.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Trying to compile qemu-x86_64_defconfig with CONFIG_CMD_ACPI=y and
CONFIG_ACPIGEN=n fails with
ld.bfd: cmd/built-in.o: in function `do_acpi_items':
cmd/acpi.c:162: undefined reference to `acpi_dump_items'
Add the missing configuration dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAV6K8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYERgf/QbwOL87yPbf9SyXBQ0EMTmn1ve9HCiv9
yeXrijvA0/wtTVoM44d/z7THb+7Zqw6LbsVOXUSicdGqaogy10xIuz5we0CoGJm6
iwYWV6kaAqjCxDTlSToGnR/TCjiOVgXC6u5QPCZC0LGbAmDbAl4jyCuQxxq2eXYD
hrLSzZPHDe0s2BeWZKRQJ26qyPfWIribXNJXG78/FsvDrdWPPc5K+/ZEb2IWawWR
nEZ8GTEYZpik/niEJ3gFozwCwpJQi3PyukjZvzTGn6tBqg12YXE4dbSzcj48Uj4o
prwUFAGKRR97zFB6c4+NUvd3VBUgPtPdZrtzZ1nNCppiMq1E4BKiDg==
=kijh
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-30jan21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
tpm fixes for coral
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reinitialize DFU USB gadget after flashing the 'SCRIPT' entity to ensure
that the potential changes to the 'dfu_alt_info' environment variable are
applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[lukma - I've moved the bool retry to avoid build (CI) errors]
Show the interface name (i.e. 'mmc') in the information string to ease
user checking which device is exported via USB Mass Storage protocol.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
On request/suggestion from Simon Glass back in May 22 2019 [1], the
'strsep' mechanism implemented in bcb_set() was set to work directly
with user-provided argv strings, to avoid duplicating memory and for
the sake of simpler implementation.
However, since we recently exposed bcb_write_reboot_reason() API to be
called by U-Boot fastboot, the idea is to be able to pass const string
literals to this new BCB API, carrying the reboot reason.
Since 'strsep' (just like its older/superseded sibling 'strtok')
modifies the input string passed as parameter, BCB command in its
current state would attempt to perform in-place modifications in a
readonly string, which might lead to unexpected results.
Fix the above with the cost of one dynamic memory allocation ('strdup').
This will also ensure no compiler warnings when passing string literals
to bcb_write_reboot_reason().
[1] http://u-boot.10912.n7.nabble.com/PATCH-v2-0-2-Add-bcb-command-to-read-modify-write-Android-BCB-td369934i20.html#a370456
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Fastboot is evolving and beginning with commit [1], the
upstream implementation expects bootloaders to offer support for:
- reboot-recovery
- reboot-fastboot
The most natural way to achieve the above is through a set of
pre-defined "reboot reason" strings, written into / read from
the BCB "command" field, e.g.:
- bootonce-bootloader [2]
- boot-fastboot [3]
- boot-recovery [4]
Expose the first 'bcb' API meant to be called by e.g. fastboot stack,
to allow updating the BCB reboot reason via the BCB 'command' field.
[1] https://android.googlesource.com/platform/system/core/+/dea91b4b5354af2
("Add fastbootd.")
[2] https://android.googlesource.com/platform/bootable/recovery/+/cba7fa88d8b9
("Add 'reboot bootloader' to bootloader_message.")
[3] https://android.googlesource.com/platform/bootable/recovery/+/eee4e260f9f6
("recovery: Add "boot-fastboot" command to BCB.")
[4] https://android.googlesource.com/platform/system/core/+/5e98b633a748695f
("init: Write the reason in BCB on "reboot recovery"")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
[lukma - added missing #include <linux/errno.h> to avoid build breaks]
Enriching the functionality of U-Boot 'bcb' may assume using the
existing sub-commands as building blocks for the next ones.
A clean way to achive the above is to expose a number of static
routines, each mapped to an existing user command (e.g. load/set/store),
with a user/caller-friendly prototype (i.e. do not force the caller
to wrap an integer into a string).
This third patch makes '__bcb_store' available for internal needs.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Enriching the functionality of U-Boot 'bcb' may assume using the
existing sub-commands as building blocks for the next ones.
A clean way to achive the above is to expose a number of static
routines, each mapped to an existing user command (e.g. load/set/store),
with a user/caller-friendly prototype (i.e. do not force the caller
to wrap an integer into a string).
This second patch makes '__bcb_set' available for internal needs.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Enriching the functionality of U-Boot 'bcb' may assume using the
existing sub-commands as building blocks for the next ones.
A clean way to achive the above is to expose a number of static
routines, each mapped to an existing user command (e.g. load/set/store),
with a user/caller-friendly prototype (i.e. do not force the caller
to wrap an integer into a string).
This first patch makes '__bcb_load' available for internal needs.
No functional change, except for a tiny update in error handling.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
On x86 platforms the EC provides a way to read 'switches', which are
on/off values determined by the EC.
Add a new driver method for this and implement it for LPC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some ARMv7 boards using PSCI require to be in secure-mode when booted via
'bootz' or 'bootm'. During distro-boot 'bootefi bootmgr' is called to check
if booting via UEFI is possible.
With the change we change the switch from secure mode to non-secure mode is
moved from the UEFI subsystem setup to just before calling StartImage().
Cc: Jernej Škrabec <jernej.skrabec@gmail.com>
Reported by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If sleeping has been interrupted, return CMD_RET_FAILURE instead of -1
(CMD_RET_USAGE).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This adds support for specifying FDT overlays in an extlinux/pxelinux
configuration file.
Without this, there is no simple way to apply overlays when the kernel
and fdt is loaded by the pxe command.
This change adds the 'fdtoverlays' keyword for a label, supporting multiple
overlay files to be applied on top of the fdt specified in the 'fdt' or
'devicetree' keyword.
Example:
label linux
kernel /Image
fdt /soc-board.dtb
fdtoverlays /soc-board-function.dtbo
append console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait
This code makes usage of a new variable called fdtoverlay_addr_r used to load
the overlay files without overwritting anything important.
Cc: Tom Rini <trini@konsulko.com>
Cc: Andre Heider <a.heider@gmail.com>
Cc: Jernej Škrabec <jernej.skrabec@siol.net>
Cc: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Jernej Škrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Škrabec <jernej.skrabec@siol.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The first argument is the load address and not an offset.
The second argument cannot be entered without the first one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default the echo command emits its arguments followed by a line feed.
If any of the arguments contains the sub-string "\c", the line feed is
suppressed.
This does not match shells used in Linux and BSD where the first argument
has to be -n to suppress the line feed.
The hush shell interferes with the parsing of backslashes. E.g. in the
following command line quadruple backslashes are required for suppressing
the line feed:
for i in 1 2 3; do for j in 4 5; do echo \\\\c ${i}${j}; done; echo; done;
To avoid unexpected behavior the patch changes echo to use -n as first
argument to suppress the line feed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
CID 316364 says:
> Null pointer dereferences (FORWARD_NULL)
> printf("Result total size: 0x%x\n", result->variable_total_size);
at do_efi_capsule_res().
The code is basically safe because a buffer for "result" is allocated
by malloc() and filled up by the second get_variable(), which fails any way
if the allocation has failed.
But the first (and second) get_variable() possibly returns an error other
than EFI_SUCCESS. We always need to check the return code from
get_variable() before accessing the data in "result".
While this change won't suppress CID 316364, the resulting code is much
safer.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some boards are very tight on the binary size. Booting via UEFI is possible
without using the boot manager.
Provide a configuration option to make the boot manager available.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the command "pwm" for controlling the pwm channels. This
command provides pwm invert/config/enable/disable functionalities
via PWM uclass drivers
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fit_print_contents prints similar fit information as printed in bootm stages.
Removing this API reduces redundancy & provides improvement in boottime.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When ESC/CTRL+C is pressed interrupt bootmenu and jump into U-Boot console.
As the last entry in bootmenu is always U-Boot console just choose the last
entry when ESC or CTRL+C is pressed.
ESC key is detected when either no other character appears after '\e'
within 10ms or when non-'[' appears after '\e'.
It is useful when bootmenu is part of boot process and you want to
interrupt boot process by scripts which control U-Boot (serial) console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add eMMC and GPT support.
- GPT partition list and command to create the GPT added to u-boot
environment
- eMMC boot commands added to u-boot environment
- new gpt commands (enumarate and setenv) that are used by broadcom
update scripts and boot commands
- eMMC specific u-boot configurations with environment saved in eMMC
and GPT support
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
[trini: Make gpt_setenv initialize ret to -1, given relevant return
error values]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a 'mbr' command to let users create or verify MBR partition layout
based on the provided text description. The partition layout is
alternatively read from the 'mbr_parts' environment variable. This can be
used in scripts to help system image flashing tools to ensure proper
partition layout.
The syntax of the text description of the partition list is similar to
the one used by the 'gpt' command. Supported parameters are: name
(currently ignored), start (partition start offset in bytes), size (in
bytes or '-' to expand it to the whole free area), bootable (boolean
flag) and id (MBR partition type). If one wants to create more than 4
partitions, an 'Extended' primary partition (with 0x05 ID) has to be
explicitely provided as a one of the first 4 entries.
Here is an example how to create a 6 partitions (3 on the 'extended
volume'), some of the predefined sizes:
> setenv mbr_parts 'name=boot,start=4M,size=128M,bootable,id=0x0e;
name=rootfs,size=3072M,id=0x83;
name=system-data,size=512M,id=0x83;
name=[ext],size=-,id=0x05;
name=user,size=-,id=0x83;
name=modules,size=100M,id=0x83;
name=ramdisk,size=8M,id=0x83'
> mbr write mmc 0
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
A boot manager like GRUB can use the protocol to
* apply U-Boot's fix-ups to the a device-tree
* let U-Boot make memory reservations according to the device-tree
* install the device-tree as a configuration table
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At 9600 baud or less a 1 ms wait is too short to detect the end of an
escape sequence.
Increase the wait duration to 10 ms which will work down to 1200 baud.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now the bootefi command used the last file loaded to determine the
boot partition. This has led to errors when the fdt had been loaded from
another partition after the EFI binary.
Before setting the boot device from a loaded file check if it is a PE-COFF
image or a FIT image.
For a PE-COFF image remember address and size, boot device and path.
For a FIT image remember boot device and path.
If the PE-COFF image is overwritten by loading another file, forget it.
Do not allow to start an image via bootefi which is not the last loaded
PE-COFF image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently when executing 'bootefi hello' we copy helloworld.efi to the
address identified by environment variable loadaddr. This is unexected
behavior for a user. There is no need to copy helloworld.efi before
executing it after relocation.
Remove the copy action.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
At present flags are stored as part of the device. In preparation for
storing them separately, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commits add a check on the command ubi rename. This check avoids
to rename a volume to with a name that is already used on another ubi
volume. If two volumes has the same name, then the ubi device can't be
mounted anymore.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add a efidebug subcommand to initiate a firmware update using the efi
firmware management protocol(fmp) set_image routine.
The firmware update can be initiated through
'efidebug capsule disk-update'
This would locate the efi capsule file on the efi system partition,
and call the platform's set_image fmp routine to initiate the firmware
update.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement the commands
* exception undefined - execute an illegal instruction
* exception sigsegv - cause a segment violation
Here is a possible output:
=> exception undefined
Illegal instruction
pc = 0x55eb8d0a7575, pc_reloc = 0x57575
Resetting ...
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present cli_simple_process_macros() requires that the caller provide
an output buffer that is exactly CONFIG_SYS_CBSIZE bytes in length. This
makes sense since it is designed to be used from the command line. But we
also want to use it for bootargs substitution.
Update the function to allow the caller to specify the buffer size. Also
return an error if the buffer is exhausted. The caller can ignore that if
preferred.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function returns 1 on success and 0 on failure. But in
the latter case it provides no indication of what went wrong.
If an attempt is made to delete a non-existent variable, the caller may
want to ignore this error. This happens when setting a non-existent
variable to "", for example.
Update the function to return 0 on success and a useful error code on
failure. Add a function comment too.
Make sure that env_set() does not return an error if it is deleting a
variable that doesn't exist. We could update env_set() to return useful
error numbers also, but that is beyond the scope of this change.
Signed-off-by: Simon Glass <sjg@chromium.org>
wip
"efidebug capsule" is more or less a debugging utility.
efidebug capsule update: invoke UpdateCapsule against data on memory
efidebug capsule show: show a capsule header
efidebug capsule result: dump a capsule result variable
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
A previous commit is adding EFI_TCG2_PROTOCOL, which in it's eventlog
support registers an EFI configuration table.
Let's add the necessary GUID so 'efidebug table' command can display
table names properly.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current tpm2_pcr_extend is hardcoded using SHA256.
Let's make the actual command to the TPM2 configurable so we can support
a wider range of algorithms and keep the current command line as-is i.e
limited to SHA256 only
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_PROMPT_HUSH_PS2 in Kconfig, depending
on CONFIG_HUSH_PARSER, and remove the default value defined
in cli_hush.c under __U_BOOT__.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for dealing with string operands, including reading a string
from memory into an environment variable and concatenating two strings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Behún <marek.behun@nic.cz>
At present a ulong is used to hold operand values. This means that
strings cannot be used. While most operations are not useful for strings,
concatenation is. As a starting point to supporting strings, convert the
code to use a struct instead of a ulong for operands.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present when more than one substitution is made this function
overwrites its buffers. Fix this bug and update the tests now that they
can pass.
Also update the debug code to show all substrings, since at present it
omits the final one.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the 'nlen' variable increases with each loop. If the previous
loop had back references, then subsequent loops without back references
use the wrong value of nlen. The value is larger, meaning that the string
terminator from nbuf is copied along to the main buffer, thus terminating
the string prematurely.
This leads to the final result being truncated, e.g. missing the last
(unmatched) part of the string. So "match match tail" become
"replaced replaced" instead of "replaced replaced tail".
Fix this by resetting nlen to the correct value each time around the lop.
Fixes: 855f18ea0e ("setexpr: add regex substring matching and substitution")
Signed-off-by: Simon Glass <sjg@chromium.org>
Add tests to check for buffer overflow using simple replacement as well
as back references. At present these don't fully pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function always allocates a large amount of stack, and
selects its own size for buffers. This makes it hard to test the code
for buffer overflow.
Separate out the inner logic of the substitution so that tests can call
this directly. This will allow checking that the algorithm does not
overflow the buffer.
Fix up one of the error lines at the same time, since it should be
printing nbuf_size, not data_size.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function assumes that a size of 4 refers to a ulong. This
is true on 32-bit machines but not commonly on 64-bit machines.
This means that the 'l' specify does not work correctly with setexpr.
Add an explicit case for 32-bit values so that 64-bit machines can still
use the 'l' specifier. On 32-bit machines, 64-bit is still not supported.
This corrects the operation of the default size (which is 4 for setexpr),
so update the tests accordingly.
The original code for reading from memory was included in 47ab5ad145
("cmd_setexpr: allow memory addresses in expressions") but I am not adding
a Fixes: tag since that code was not written with 64-bit machines in mind.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these values are open-coded in a few places. Add constants so
the meaning is clear.
Also add a comment to cmd_get_data_size()
Signed-off-by: Simon Glass <sjg@chromium.org>
As FDTDIR label doesn't specify exact file to be loaded, it should
not fail if no file exists in the directory. In this case try to boot
with internal FDT if it exists.
Signed-off-by: Anton Leontiev <aleontiev@elvees.com>
For implementing the EFI_TCG2_PROTOCOL we need the count field returned by
the TPM when reading capabilities via tpm2_get_capability().
Adjust the implementation of the 'tpm2 get_capability' command accordingly.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This command was missed when renaming getc() to getchar().
Fixes: c670aeee3d ("common: rename getc() to getchar()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This adds several commands to add, list, and remove log filters. Due to the
complexity of adding a filter, `log filter-list` uses options instead of
positional arguments.
These commands have been added as subcommands to log by using a dash to
join the subcommand and subsubcommand. This is stylistic, and they could be
converted to proper subsubcommands if it is wished.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the log level command print all valid log levels. The default
log level is annotated. This provides an easy way to see which log levels
are compiled-in.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows users to query which categories and drivers are available on
their system. This allows them to construct filter-add commands without
(e.g.) adjusting the log format to show categories and drivers.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move parsing of log level into its own function so it can be re-used. This
also adds support for using log level names instead of just the integer
equivalent.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reduces duplicate code, and makes adding new sub-commands easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When rebasing this series I had to renumber all my log tests because
someone made another log test in the meantime. This involved updaing a
number in several places (C and python), and it wasn't checked by the
compiler. So I though "how hard could it be to just rewrite in C?" And
though it wasn't hard, it *was* tedious. Tests are numbered the same as
before to allow for easier review.
A note that if a test fails, everything after it will probably also fail.
This is because that test won't clean up its filters. There's no easy way
to do the cleanup, except perhaps removing all filters in a wrapper
function.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Checkpatch complains about using #ifdef for CONFIG variables.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This command lets the user list, select, and deselect mux controllers
introduced with the mux framework on the fly. It has 3 subcommands:
list, select, and deselect.
List: Lists all the mux present on the system. The muxes are listed for
each chip. The chip is identified by its device name. Each chip can have
a number of mux controllers. Each is listed in sequence and is assigned
a sequential ID based on its position in the mux chip. It lists details
like ID, whether the mux is currently selected or not, the current
state, the idle state, and the number of states.
A sample output would look something like:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no unknown as-is 0x4
1 no 0x2 0x2 0x10
2 no 0x73 0x73 0x100
another-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x2 0x2 0x4
Select: Selects a given mux and puts it in the specified state. This
subcommand takes 3 arguments: mux chip, mux ID, state to set
the mux in. The arguments mux chip and mux ID are used to identify which
mux needs to be selected, and then it is selected to the given state.
The mux needs to be deselected before it can be selected again in
another state. The state should be a hexadecimal number.
For example:
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
=> mux select a-mux-controller 0 0x3
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 yes 0x3 0x1 0x4
1 no 0x1 0x1 0x4
Deselect: Deselects a given mux and puts it in its idle state. This
subcommand takes 2 arguments: the mux chip and mux ID to identify which
mux needs to be deselected. So in the above example, we can deselect mux
0 using:
=> mux deselect a-mux-controller 0
=> mux list
a-mux-controller:
ID Selected Current State Idle State Num States
0 no 0x1 0x1 0x4
1 no 0x1 0x1 0x4
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
do_save() function defined in fs.c also supports FAT file system
re-use the same for fatwrite command.
Also fix the FAT test script to match the expected output.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
