This is a rework of a previously submitted patchset and bundles the
main board support and USB support into a single commit.
It requires the patch "mx5: add iomux-mx51.h include"
* Use iomux-mx51.h include to simplify board configuration.
* Simplify LED support (remove efikamx_toggle_led, change lit LEDs).
* Simplify MMC support for CD and WP pin differences.
* Fix broken CPU voltage setting - comment said 1.1V but the code set to
1.2V. It should never have been set to 1.2V even on i.MX51 TO2 and
all available Linux kernels would drop the voltage to 1.1V anyway and
work reliably. This should lower power consumption during the boot
process.
* Function renames for readability.
* Some board identification string changes to match actual product names.
* Passes checkpatch (v2)
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Cc: Stefano Babic <sbabic@denx.de>
For representing a timeout value, it makes more sense to pass it as
'unsigned int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Update maintainer for "efikamx" and "efikasb" to myself.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
PCBID pads seem to need time to settle due to external pulldowns, otherwise
we are reading floating GPIO pins with implicit pad pullups and get the wrong
data. However we can't "wait" at the time we need them before relocation,
since timers are not available. The time taken to get from DCD to the code
requiring the pads set seems to be more than long enough (even with caches
enabled).
We have space in the DCD due to the DDR settings changes to configure all
the pad settings we need for this, plus the LED pad settings too which
reduces the amount of code required later on.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Efika MX boards configure their DDR pad settings twice, one in the DCD generated
from imximage_*.cfg and again in init_drive_strength called before relocation.
Rather than doing this, roll the changes it makes into the DCD so DDR is set up
before a single line of code in U-Boot is run.
The settings are identical with this DCD block which is shorter (by 7 entries)
than the old one, and after the output of init_drive_strength since a lot of the
functionality in the existing DCD and init_drive_strength function was just
setting the POR defaults. This goes to explain some now-missing entries.
Several hundred rounds of mtest have been run to test the settings before and
after to confirm DDR is stable and no ill-effects have been found.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
* Move Efika MX Smarttop and Smartbook boards into a "genesi" vendor directory
* Rename efikamx -> mx51_efikamx since there is an mx53_efikamx and mx6_efikamx to come
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Align the SSP clock speed with oscilator to achieve
higher transfer stability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
This change implements DMA chaining into SPI driver. This allows
the transfers to go much faster, while also fixing SF issues.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Load from SPI flash can create a long DMA chain, which can take long
time to transfer. Change the DMA timeout to roughly 10s to prevent
such long chains misreporting errors.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allow usage of the imx-common/iomux-v3.h framework by including pad settings
for the i.MX51. The content of the file is taken from Linux kernel at
commit 5d23b39 plus the required changes to make it work in U-Boot.
The contained pad settings are the minimum required to make an Efika MX boot
and get all the currently-implemented peripherals working in U-Boot.
It is recommended that this file not be just a dumping ground for pins but
only contain the settings required for all the boards using it.
Changes for v2:
* reference commit id from Linux kernel
* additionally roll in the USB pads
* removed GPIO_NUMBER define
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The DRAM initialization, after SPL has complete, is exactly the same
for all mxs SoCs so we should name it accordinly.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
The internal Ethernet controller is only available on i.MX28
processors so it needs to use CONFIG_MX28 guardian to avoid having
this code called in others.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
gpio_get_value() should use PSR like Linux, not DR, because DR does not always
reflect the pin state, while PSR does. This is especially useful to detect a
short circuit on a GPIO pin configured as output, or to read the level of a pin
controlled by a non-GPIO IOMUX function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
The imx_decode_pll() function does not exist for mx5, so remove its declaration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Each i.MX has its own gpio.h, defining the same structure.
The internal GPIO controller has the same layout
(at least for the register used by u-boot) and can be shared.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Matt Sealey <matt@genesi-usa.com>
commit d92591a (mxs: Convert sys_proto.h prefixes to 'mxs') introduced
a mxs_dram_init() function, which is not used anywhere.
Fix it, so that the following warning goes away:
mx28evk.c: In function ‘dram_init’:
mx28evk.c:67:2: warning: implicit declaration of function ‘mx28_dram_init’ [-Wimplicit-function-declaration]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
There is no need to undef an option that is not enabled by default.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
For i.MX233 addition the base registers need to be change so the SoC
definition needs to be known before the header include.
The following boards has been changed:
* apx4devkit
* m28evk
* mx28evk
* sc_sps_1
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The elftosb call needs to use a target param specific for i.MX28. This
patch allow for later addition of i.MX233.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
Add cpu_mmc_init() function to make it easy to init a single eSDHC instance.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Do not pretend to have initialized mmc successfully if CONFIG_FSL_ESDHC is not
defined. Instead, only implement a custom cpu_mmc_init() when it does something.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Use calloc() instead of malloc() to allocate the mxs_spi_slave structure.
Clearing the memory is necessary since most of the time this gets done
super early in boot, but on warm reboots, and when SPI probing is done
long after the init stages it could actually pick up previously used memory,
and things like the chipselect polarity and other data end up being filled
with trash data if not explicitly set by the board files.
This solves a semi-random, almost unreproducable error whereby SPI devices
act very, very strangly on boot.
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Use calloc() instead of malloc() to allocate the mxc_spi_slave structure.
Clearing the memory is necessary since most of the time this gets done
super early in boot, but on warm reboots, and when SPI probing is done
long after the init stages it could actually pick up previously used memory,
and things like the chipselect polarity and other data end up being filled
with trash data if not explicitly set by the board files.
This solves a semi-random, almost unreproducable error whereby SPI devices
act very, very strangly on boot. Tested on Efika MX over several years..
Signed-off-by: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This allows a watchdog reset to start the ROM's
usb/serial downloader, or boot from an sdcard.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This is useful for forcing the ROM's
usb downloader to activate upon a watchdog reset.
Or, you can boot from either SD Card.
Currently, support added for MX53 and MX6Q
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Note: MX53 support untested.
Acked-by: Stefano Babic <sbabic@denx.de>
Round up tick_to_time() value instead of truncating it. This avoids stopping
waits instantly for low usec values, and this generally guarantees that the code
always waits for at least the requested duration.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Now that the main i.MX features work fine with dcache enabled, enabled it by
default if CONFIG_SYS_DCACHE_OFF is not defined.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Since the input frequency of the API is a maximum that should not be exceeded in
order for the devices to operate properly, the SPI clock divider should be
rounded up, not truncated.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
