Commit graph

22 commits

Author SHA1 Message Date
Aswath Govindraju
750d8470cb arm: dts: k3-am654-r5-base-board: Fix the dt properties in usb0 instance
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2022-06-10 13:37:32 -04:00
Lokesh Vutla
654b60a8fd arm: dts: k3-am654-base-board: Add r5 specific u-boot dtsi
So far all the u-boot specific properties for both r5 and a53 are
placed in k3-am654-base-board-u-boot.dtsi. But there are few a53
nodes that should be updated but doesn't belong to r5. So create a
separate r5 specific u-boot dtsi.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210622063431.3151-4-lokeshvutla@ti.com
2021-07-15 17:56:04 +05:30
Lokesh Vutla
e497876343 arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot
Sync all AM65 related v5.11-rc6 Linux kernel dts into U-Boot.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2021-02-04 20:37:57 +05:30
Faiz Abbas
2121c7e2d5 arm: dts: k3-am65: Fix mmc nodes
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts

This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode

While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
2021-02-04 20:37:57 +05:30
Nishanth Menon
965db9fb0c arm: dts: k3-*-r5-*-board: Add GTC clock
Add GTC Clock definition as index 0 clock so that we can use the clock
node in the driver later on.

Signed-off-by: Nishanth Menon <nm@ti.com>
2021-01-12 10:59:04 +05:30
Faiz Abbas
5251eb13bd arm: dts: k3-am654-r5-base-board: Add USB0 nodes
Add USB0 nodes and set them to host mode to support USB host and
peripheral boot modes

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2020-08-11 20:34:46 +05:30
Vignesh Raghavendra
d5a1f4f551 arm: dts: k3-am654: Increase OSPI default frequency to 50MHz
In 1 bit mode OSPI can work at upto 50MHz, this provides better write
performance. Therefore increase frequency from 40MHz to 50MHz

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-04-14 15:44:48 +05:30
Vignesh Raghavendra
9e9dfc1fc4 ARM: dts: k3-am65: Add OSPI DT nodes
Add OSPI DT nodes to enable OSPI at U-Boot prompt and also to support
OSPI boot.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
2020-03-03 13:08:13 +05:30
Lokesh Vutla
57a088a0f0 arm: dts: k3-am654-r5-base-board: Fix power-domains for wkup_vtm0
wkup_vtm populates only 1 power-domain cell in it's node. But the
power-domain cell are defined as 2. Due to this the following warning
comes during build:

arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property):
/interconnect@100000/interconnect@28380000/interconnect@42040000/
wkup_vtm@42050000:power-domains: property size (8) too small for cell size 2

Fix this by updating the power-domain cells.

Fixes: cfa6bd549c ("arm: dts: k3-am654-r5-base-board: Add VTM node")
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2020-01-20 10:10:28 +05:30
Tero Kristo
56adc6615f arm: dts: k3-am654-r5-base-board: enable wkup_vtm0 node and link in supplies
Link the vdd-supplies for the voltage domains under the VTM node. Also,
enable the node under SPL. This will enable the AVS class 0 support on
am65x-evm board.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
Tero Kristo
c5f73d1c9f arm: dts: k3-am654-r5-base-board: add supply rail for MPU
MPU voltage on AM65x-evm is controlled via the TPS62363 chip attached
to i2c0 bus. Add device node for this so that it can be controlled via
a regulator driver.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
Tero Kristo
4bbb3849aa arm: dts: k3-am654-r5-base-board: enable wkup_i2c0 driver for spl
Enable wkup_i2c0 as this is needed for voltage control.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
Keerthy
cfa6bd549c arm: dts: k3-am654-r5-base-board: Add VTM node
Add VTM node for voltage and thermal management. For u-boot, this is needed
for supporting AVS class 0, as the efuse values for the OPPs are stored
under the VTM.

Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-11-07 18:39:17 -05:00
James Doublesin
d5e08fd204 armv7r: dts: am654-base-board: Rename 1600MHz to 1600MTs in dtsi filename
The current configuration of DDR on AM654 base board is for 1600MTs but
the file name is specified as k3-am654-base-board-ddr4-1600MHz.dtsi.
Since 1600MHz is misleading, rename it to
k3-am654-base-board-ddr4-1600MTs.dtsi

Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-10-25 17:33:21 -04:00
Andreas Dannenberg
20a229676e armv7R: dts: k3: am654: Add MCU_UART0 related definitions
Although we currently use the MAIN_UART0 for R5 SPL console output there
are cases where we require access to the MCU_UART0 as well for example in
case of UART-based Y-Modem boot. To support these scenarios add related
DTS definitions to be able to use that UART early on.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
2019-10-11 10:07:33 -04:00
Lokesh Vutla
355be915ed arm: dts: k3-am654: Update power-domains property for each node
Update the power-domain-cells to 2 and add the permissions
to each node. Mark the following nodes accessed by r5 as shared:
- DDR node
- main uart 0

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-26 21:49:23 -04:00
Andreas Dannenberg
7e0363b285 arm: dts: k3-am654-base-board: Enable wkup_i2c0 across all boot stages
To enable the use of an EEPROM-based board detection scheme we need to
be able to access the I2C bus associated with the EEPROMs across all
3 stages of U-Boot: R5 SPL, A53 SPL, and A53 U-Boot (proper). So go
ahead and add/update the wkup_i2c0 peripheral module DTS definitions
and its associated pinmux node accordingly.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-17 11:13:18 -04:00
Faiz Abbas
bbcfaad59f arm: dts: k3: Add phy specific properties to SD card node
With changes in the driver requiring phy related properties,
add the same for the SD card node to prevent breaking boot with
the driver update.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Faiz Abbas
3a1a0dfc39 arm64: dts: k3: Sync sdhci0 node from kernel and change driver name
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.

Also change the name of the driver to match the compatible in kernel.

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17 11:12:08 -04:00
Andreas Dannenberg
7202af927b arm: dts: k3-am654: Sync IOPAD macros with Linux
Transition to the IOPAD macros as used in Linux in which the pin mux
mode is specified using a dedicated parameter while also dropping the
related MUX_MODEx macros that are no longer needed. This transition
will allow us to keep both Linux and U-Boot DTS in sync more easily.
While at it also align the file name of the include file itself and
update any references accordingly.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-05-03 07:30:31 -04:00
Andreas Dannenberg
12df71cd74 armv7R: dts: k3: am654: Switch DMSC TX message thread ID
Switch from using the high priority DMSC transmit message queue used
by the secure R5 MCU island boot context to the low priority message
queue. While the change in priority is irrelevant for the current boot
architecture it however gives us access to a deeper message queue that
will allow us to buffer more messages. This is an important aspect when
sending several messages without requesting and waiting for a response
in a row which is a communication scheme used during core shutdown for
example. See AM654 TISCI User Guide for additional details.

Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-05-03 07:23:17 -04:00
Lokesh Vutla
00b34e9937 armv7r: dts: am654: Add initial support
Add R5 specific dts for am654-evm.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-11-16 16:51:59 -05:00