Using mkimage with e.g.
tools/mkimage -A arm -T firmware -O u-boot -d u-boot.bin foo.img
gives a warning
"Unknown OMAP image type - 5"
while it seems that the image itself is created successfully.
This does come from the patch "mkimage: Add OMAP boot image support".
The method check_image_type in image_type_params is supposed to just
return success or failure. However, for omap it also calls fprintf:
static int omapimage_check_image_types(uint8_t type)
{
if (type == IH_TYPE_OMAPIMAGE)
return EXIT_SUCCESS;
else {
fprintf(stderr, "Unknown OMAP image type - %x", type);
return EXIT_FAILURE;
}
}
All the other image checkers and no others have this, so the fix is to
simply remove the fprintf.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: John Rigby <john.rigby@linaro.org>
CC: Aneesh V <aneesh@ti.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
This is a cosmetic patch, which is changing the gpio_ prefix to
s5p_gpio_.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Fix buld error:
undefined reference to '__image_copy_end' and `save_boot_params'.
start.o: In function `_image_copy_end_ofs':
mmc_spl/board/samsung/smdkv310/start.S:44: undefined reference to `__image_copy_end'
start.o: In function `reset':
mmc_spl/board/samsung/smdkv310/start.S:137: undefined reference to `save_boot_params'
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is driven by need of general gpio_* functions,
which as their parameter are accepting the GPIO pin number, NOT
block and pin.
This makes the code alike to omap, and allows for using more
generic frameworks (e.g. software I2C).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt. Since the DMA interrupt is not enabled it will hang
the MMC driver.
This patch adds support for restarting the DMA transfer. The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit. So we can read that
and write it back. The write triggers the resumption of the
transfer.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tested-by : Jaehoon Chung <jh80.chung@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Fix compilation of mkv310_image host tool
tools/mkv310_image.c: In function 'main':
tools/mkv310_image.c:67: error: 'S_IRUSR' undeclared (first use in this function)
tools/mkv310_image.c:67: error: (Each undeclared identifier is reported only once
tools/mkv310_image.c:67: error: for each function it appears in.)
tools/mkv310_image.c:67: error: 'S_IWUSR' undeclared (first use in this function)
tools/mkv310_image.c:67: error: 'S_IRGRP' undeclared (first use in this function)
tools/mkv310_image.c:67: error: 'S_IWGRP' undeclared (first use in this function)
tools/mkv310_image.c:67: error: 'S_IROTH' undeclared (first use in this function)
tools/mkv310_image.c:67: error: 'S_IWOTH' undeclared (first use in this function)
resulting from a 'make smdkv310_config'.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
gd->bd pointer has been used prior been initialized.
Move the relevant code after the initialization.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
CONFIG_L2_OFF is obsolete after the following commit:
e47f2db537
armv7: rename cache related CONFIG flags
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
Since imx5 does not provide L2 cache operations(Enable/Disable)
Simply remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Cc:Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
This deletes the integrator split_by_variant.sh script and
defines a number of unique board types for the core modules
that are meaningful to support for the Integrator AP/CP, i.e.
the ones that did not just say "unsupported core module" in
split_by_variant.sh. If more core modules need to be supported
they are easy to add.
We delete all the old cruft in Makefile and MAKEALL that was
working around the old way of building boards. We create a
unique config file per board to satisfy the build system, but
they are just oneliners that include the existing
integratorap.h and integratorcp.h configs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The default configuration for the Integrator AP forces memory to be
32 MB on the command line to the kernel, while we have perfect
information and detection of the actual memory size in the ATAGs.
Delete the confusion.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for a subset of the default commands for the
Integrator, however since the card does not have Ethernet (unless
you plug in a PCI card) we can not use the default command set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integrator board was apparently never converted over to support
relocation until now. After this the integrator u-boot both compiles
and boots on the Integrator AP.
This also fixes the SDRAM memory size detection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The integratorap/cp config for u-boot was outdated and would not
even compile, so fix the obvious missing bits for it to start
building. After this "make ap920t_config/make all" starts working
again.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some cases (e.g. bootm with a elf payload which is already at the right
position) there is a in place copy of data to the same address. Catching this
saves some ms while booting.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Innovator and H2 boards used machine_is_* macros for setting the machine
type. These macros are expanded in compile time and thus leaves
unreachable code (though gcc might optimize it).
Switch them to use common code for machine type setting.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
NVIDIA boards and Samsung SMDK6400 already use a local variant of
CONFIG_MACH_TYPE option.
Switch to use the new common code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
The meesc board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Signed-off-by: Matthias Fuchs <Matthias.Fuchs@esd.eu>
Commit 7616e78 "Add Ethernet hardware MAC address framework to usbnet"
increased the code size and broke building for the ETX094 board.
Adjust the linker script to make it build again.
While we are at it, remove unused u-boot.lds.debug
Signed-off-by: Wolfgang Denk <wd@denx.de>
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: TSEC0 connected to Marvell 88E1111S
TSEC1 connected to Marvell 88E1111S
TSEC0, TSEC1
...
Turn printf() into debug() so we het the expected output again:
...
Net: TSEC0, TSEC1
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Some SH have MMC controller. So, if we need it, we have to call
the mmc_initialize().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The sh7757lcr has a local u-boot.lds because the sh7757lcr is only
supported the SPI booting.
This patch refers from the commit "sh: Add KEEP order to start.o section"
(commit ID: b52da2aed8).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Adjusted default settings so that we can boot zImages and uImages.
Removed unused settings, use default commands and where possible
calculate all other settings.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Only the optimization of sh2 had been supported up.
This adds the optimization of sh2a.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH2A toolchains often only provide an fdpic version of libgcc. This
can't be used with bare-metal software like U-Boot, so this patch
provides the necessary functions extracted from libgcc.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Free private_data member element before freeing file structure.
This was causing malloc to crash. Also remove unnecessary variable
assigments as file structure gets free'd as well.
Signed-off-by: Rod Boyce <uboot@teamboyce.co.uk>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
If you take a look at 96820a35, you'll see the original timeout was
CONFIG_SYS_HZ. Which is 1000. After the mentioned change, non-bulk timeout
was changed to 100. This causes timeout failures on the dreamplug platform
when trying to initialize the usb microsd reader.
Signed-off-by: Jason Cooper <u-boot@lakedaemon.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
