As explained in commit 3bedbcc3aa ("arm: mvebu: a38x: serdes: Don't
overwrite read-only SAR PCIe registers") it is required to set Maximum Link
Width bits of PCIe Root Port Link Capabilities Register depending of number
of used serdes lanes. As this register is part of PCIe address space and
not serdes address space, move it into pci_mvebu.c driver.
Read number of PCIe lanes from DT property "num-lanes" which is used also
by other PCIe controller drivers in Linux kernel. If this property is
absent then it defaults to 1. This property needs to be set to 4 for every
mvebu board which use PEX_ROOT_COMPLEX_X4 or PEX_BUS_MODE_X4.
Enabling of PCIe port needs to be done afer all registers in PCIe address
space are properly configure. For this purpose use new mvebu-reset driver
(part of system-controller) and remove this code from serdes code.
Because some PCIe ports cannot be enabled individually, it is required to
first setup all PCIe ports and then enable them.
This change contains also all required "num-lanes" and "resets" DTS
properties, to make pci_mvebu.c driver work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Enabling and disabling PCIe ports is done via address space of system
controller. All 32-bit Armada SoCs use low 4 bits in SoC Control 1 Register
for enabling and disabling some or more PCIe ports. Correct mapping needs
to be set in particular DTS files.
DT API for mvebu-reset is prepared for implementing resets also for other
HW blocks, but currently only PCIe is implemented via index 0.
Currently this driver is not used as PCIe ports are automatically enabled
by SerDes code executed by U-Boot SPL. But this will change in followup
patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add a node for the watchdog timer based on the proposed Linux
device tree bindings.
Remove the old reboot node which was a watchdog timert node in
disguise using a preliminary device tree binding.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-on: Apple M1 Macbook
Tested-by: Simon Glass <sjg@chromium.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
All i.MX8MQ boards have been converted to binman, which makes it
necessary to flash both flash.bin and u-boot.itb to get a bootable
system. Prior to the conversion, only flash.bin was needed.
Such new requirement breaks existing distro mechanisms to generate the
final binary because the extra u-boot.itb is now required.
Generate a final flash.bin that can be used again as a single bootable
binary to keep the original behavior.
After this change the SPL binary is called spl.bin, which is a more
descriptive name for its purpose, and can still be used standalone (for
example, for secure boot purposes).
Also update imx8mq_evk.rst to remove the u-boot.itb copy step.
This is a cherry-pick of 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") adjusted to apply to i.MX8MQ.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in imx8mm-kontron-n801x-s-u-boot.dtsi and causes
a build error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The binman node is part of the imx8mm-u-boot.dtsi file which
is duplicated in phycore-imx8mm-u-boot.dtsi and causes a build
error. Remove the duplicate.
Fixes: 3cbb31f0e848 ("arm64: dts: imx8mm: use common binman configuration")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Rather than using odd implicit blob-ext naming, explicitly specify the
type to be of blob-ext and therefore also simplify the node naming.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With the move to using binman to generate SPL aka u-boot-spl-ddr.bin and
U-Boot proper aka u-boot.itb every board now covers such configuration
in its own U-Boot specific device tree include. Move the comon part of
that configuration to the common imx8mm-u-boot.dtsi include file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Somewhere along the line, the board stopped being able to boot.
Rather than just fixing the issue, let's fix the issue and migrate
to binman to eliminate a warning when using custom imx tools for
generating the binary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
To eliminate a warning when using custom imx tools for generating
a binary, use binman to generate flash.bin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes booting from the mSD card from both SPL and when
using it for the OS booting. It also cleans up a few mmc
booting bits that are no longer needed.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
10.1" OF is a capacitive touch 10.1" Open Frame panel solutions.
PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the px30 devicetree files from linux-next tree.
commit <14ce8069f48b> ("lib/stackdepot: allow optional init and
stack_table allocation by kvmalloc() - fixup3")
Note, this path even sync rk3326 files as it depends on px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
dmc node is specific to U-Boot, it is always better practice
to maintain U-Boot specific nodes into -u-boot.dtsi files
in order to maintain Linux dts file sync compatibility.
Move the dmc into px30-u-boot.dtsi, also add dmc node
explicitly in rk3326-odroid-go2-u-boot.dtsi since it is
using px30.dts.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
adapting commit ac804143cf ("mmc: rockchip_sdhci: add phy and clock
config for rk3399") to fix the issue "Not found emmc phy device".
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com> - on a Rock960
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Patrick Wildt <patrick@blueri.se> - on a Pinebook Pro
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable sdhci and sdmmc0 node in rk3568-u-boot.dtsi
Signed-off-by: Nico Cheng <nico.cheng@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Odroid Go Advance has a hardware random number generator present.
The device does not have an upstream Linux driver, but does have a
U-Boot driver. Add the appropriate node so that the hardware RNG can be
used in U-Boot.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty devicetree file for these boards. It seems to be possible to
obtain a real one from another bootloader called 'bolt' but I will leave
this to the maintainer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty file to prevent build errors when building with
CONFIG_OF_SEPARATE enabled.
Unfortunately there are no build instructions in the U-Boot tree to enable
a real file to be created.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
The real devicetree is created by the Xen project on-the-fly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sync these file, obtained from Linux v5.15.
Add a note for the maintainer, and SPDX lines where they are missing.
The added lines are:
SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
Note, this matches the text in those files, but is not the same as the
GPL-2.0 of some files.
[1] https://releases.linaro.org/android/reference-lcr/juno/7.1-17.05/
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sync these files, obtained from Linux v5.15.
This adds a devicetree file for rpi_4 which was not there before.
Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4
I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This uses QEMU virt which creates its own devicetree.
Add an empty version of this file, so that we can at least build this
board when devicetrees are required.
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the 'missing-msg' for blobs for more detailed output on missing system
firmware and SEBoot blobs.
Signed-off-by: Ivan Mikhaylov <ivan.mikhaylov@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix minor typos:
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The alternate function of PD20 is 4 as per the datasheet of
sama7g5 and not 5 as defined earlier.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device trees for the Beacon RZ/G2[MNH] boards have undergone
some changes over time, so resync them now.
Signed-off-by: Adam Ford <aford173@gmail.com>
Commit 03510bf621 ("sunxi: only include alias for eMMC when mmc2
used") protected the eMMC alias in U-Boot's DT stub the with the
associated Kconfig symbol, but was actually using the wrong name.
Fix the name of the symbol to match what's defined in Kconfig and what
the defconfig files actually use.
Fixes: 03510bf621 ("sunxi: only include alias for eMMC when mmc2 used")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: 5kft@5kft.org
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
QSPI0 has a MX66LM1G45G SPI NOR flash connected.
Enable the controller and describe the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama7g5 embedds an OSPI and a QSPI controller:
1/ OSPI0 Supporting Up to 200 MHz DDR. Octal, TwinQuad, Hyperflash
and OctaFlash Protocols Supported.
2/ QSPI1 Supporting Up to 90 MHz DDR/133 MHz SDR.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
