Move i.MX auxiliary core memory base and size configuration
to defconfig where it should belong.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Update the distro config env memory layout for the Colibri iMX8X:
- kernel_comp_addr_r=0xb0000000 temporary area for uncompressing (ie FIT
images or Image.gz booted using booti)
- kernel_comp_size=0x08000000
- loadaddr=0x95400000 avoiding any reserved areas located before that
- fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel
- scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt
- ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script
Idea of memory layout taken from commit a9f1e35bed
("apalis-imx8: update env memory layout").
Note that for our regular BSP Layers and Reference Images for Yocto
Project an updated distro boot script is required (see
meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
The following expression is used to construct the device tree name:
fdtfile=${soc}-colibri-${fdt_board}.dtb
- soc is set dynamically (either imx8qxp or imx8dx)
- fdt_board can be modified by the user (eval-v3, aster, iris/iris-v2)
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Enable a call to ft_system_setup() which reserves M4 memory region.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Provide proper sys prompt, which should be "Colibri iMX8X #".
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Refactor the detection of QXP vs. DX SoC into its own helper function.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Remove obsolete SDHC related config defines. Nowadays, all SDHC related
hardware configuration comes from the device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Remove obsolete net USB start.
While at it also add a comment about enabling distro-boot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This commit does remove the options argument from the console
kernel-argument as it prevents the serial driver from outputting
anything.
Do this by switchting to use the variable "setup" as it is done on other
Toradex modules.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
All Colibri iMX8X variants have 2nd RGMII on SoC, so add the address
for 2nd ethernet.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Since commit 1fa43cad86 ("video: Drop references to CONFIG_VIDEO et al")
the mx51evk_video.c is no longer used.
Remove the unused file.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit 1fa43cad86 ("video: Drop references to CONFIG_VIDEO et al")
the mx53loco_video.c is no longer used.
Remove the unused file.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add mmc1, which is mapped to optional on-SoM microSD socket,
to the list of distro boot command boot devices.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Enable CONFIG_DM_SERIAL on DH i.MX6 DHSOM to convert it to DM serial .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Now that the gwventana_emmc_defconfig is the same as the
gwventana_gw5904_defconfig we can remove the latter.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MV88E61XX switch is used on the GW5904 which is an eMMC based board.
Adding it here allows us to remove the gwventana_gw5904_defconfig.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The ocotp driver is available for regular and SPL builds using the
(SPL_)MXC_OCOTP configuration. Also, the ocotp driver does not support
the driver model (DM) configuration.
But, for SPL builds, the SPL_MXC_OCOTP configuration depends on
SPL_MISC which implies on SPL_DM.
This commit replaces the dependency on SPL_MISC with SPL_DRIVERS_MISC.
So the only requirement is to have enabled miscellaneous drivers for
the SPL.
Signed-off-by: Jean-Marie Lemetayer <j.lemetayer@kerlink.fr>
The PHY nodes may be activated via DTO in case another SoM variant
is populated into the development kit. Do not delete the nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The current variant of the SoM has LAN8740Ai PHY connected to EQoS
strapped to MDIO address 0 , adjust the MDIO address to match the
hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may be populated with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY attached to EQoS MAC, and either external RGMII PHY
or LAN8740Ai RMII PHY attached to FEC MAC. The SoM configuration can be
detected for each MAC by reading RX_CTL pull resistor state early on boot.
Make use of this, detect the exact PHY configuration, and patch control DT
accordingly so that the ethernet is configured correctly in U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
The DH electronics i.MX8M Plus DHCOM SoM currently supports only 4 GiB
of DRAM population option. Add another population option with 2 GiB of
DRAM. The chips used on the 2 GiB option are 2x K4F6E3S4HM-MGCJ .
Signed-off-by: Marek Vasut <marex@denx.de>
Enable LTO to reduce the size of SPL, which with multiple DRAM
calibration tables may be close to the limit.
Signed-off-by: Marek Vasut <marex@denx.de>
Make sure that the bad block table in flash is used on Colibri iMX7.
Without this configuration enabled U-Boot corrupts the bad block table
and Linux will update the table on each reboot. The corruption occurs
because if CONFIG_SYS_NAND_USE_FLASH_BBT is not set, U-boot will store
bad blocks out of band, while the Linux driver for the iMX7 will store
them in band in a bad block table.
Fixes: fd8c1fc943 ("arm: dts: imx7: colibri: add raw NAND support")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There was a conflict between the following two commits, that wasn't
resolved correctly. Fix this.
a93985ddfc ("doc: sl-mx8mm: Update the NXP TF-A source reference")
f0f461287e ("imx: Suggest the NXP ATF github repo")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Definitions are according to the MV78460 Hardware Specifications.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM fills into bits [31:28] of register 0x182d0 tracing value,
which represents in which state BootROM currently is. BootROM fills one
of the possible values: 0x2 (CPU initialization), 0x3 (UART detection),
0x6 (UART booting), 0x8 (PCI Express booting), 0x9 (parallel or SPI NOR
booting), 0xA (parallel or SPI NAND booting), 0xB (SATA booting) and 0xE
(SD / eMMC booting).
Meaning of these values matches TRACE_* macros from Marvell soc_spec.h file:
https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/blob/u-boot-2013.01-armada-18.06/tools/marvell/doimage_mv/soc_spec.h
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This allows to merge BOOT_FROM_MMC and BOOT_FROM_MMC_ALT constants to one
macro. And also allows to extend other BOOT_FROM_* macros for other
variants.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x22 as SPI-NAND. So remove
incorrect definition 0x22 as SATA. SATA on A385 has configuration 0x2A.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A385 BootROM treats strapping configuration 0x3f as invalid. When booting
fails (e.g. because of invalid configuration) then BootROM fallbacks to
UART booting.
Detecting BootROM fallback to UART booting is implemented in U-Boot since
commit 2fd4284051 ("ARM: mach-mvebu: handle fall-back to UART boot").
So there is no need to define BOOT_FROM_UART_ALT constant and special
handling for it anymore, remove it.
This change effectively revers commit f3a88e2ca1 ("arm: mvebu: fix boot
from UART on ClearFog Base").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Tested-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Show correct information in debug() output and use correct names for variables.
No functional change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
[upstream of vendor commit 19a96f7c40a8fc1d0a6546ac2418d966e5840a99]
The Clearfog devices have only one SDHC device. This is either eMMC if
it is populated on the SOM or SDHC if not. The Linux device tree assumes
the SDHC case. Detect if the device is an eMMC and fixup the device-tree
so it will be detected by Linux.
Ported from vendor repo at https://github.com/SolidRun/u-boot
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This new clearfog_spi_defconfig file is a copy of existing
clearfog_defconfig file modified to instruct build system to generate
final kwbimage for SPI booting and to store the environment in SPI.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
A388 Clearfog MMC is either SD Card or eMMC with different behaviour for
both. Setting the device to non-removable in the u-boot.dtsi allows both
to correctly detect the device.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
I don't have access to the mx6sxsabreauto board, so remove myself
from the MAINTAINERS entry and add Peng instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
