Certain older kernels in use by some customers erroneously define a uart3
for GW54xx with a pinmux that conflicts with NAND. This will remove
that node to avoid such conflicts.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Updated 16bit DDR calibration using values obtained from running the
i.MX6 DDR Stress Test tool over a set of boards over full operationg
temperature.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x-A revision does not have the CSI0_DATA_EN pin connected, therefore
we need to make sure that signal is not muxed to the CSI_DATA_EN signal
internally and do so by steering it to the unused GPIO5_IO20.
We do this so that the kernel device-tree can properly define the signal for
RevB and beyond boards that do have this hooked up properly and require it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a new voltage rail added in various -C revision PCB's.
Additionally make VDD_CORE, VDD_SOC, and VDD_IO2 common as all Ventana boards
have those.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Certain OS bootscripts need to know how much memory a board has to adjust
kernel parameters (namely Android). This allows those boards to determine
mem size in MB.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The min/max of each depends not only on board but on CPU. Simplify by removing
this rarely needed and difficult to maintain feature and just display the
rails and their values.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Added support in default boot scripts to find kernel/dtbs on a boot volume
separate from rootfs volume.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW551x is a small form factor board based on the IMX6 SoC that includes:
* up to 512MB DDR3 memory
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
A board level errata causes the IMX6 watchdog to be unstable on the GW51xx
RevA and RevB boards which can cause the watchdog to trip extremely early
(under 5seconds) under certain operating conditions. Disable the watchdog
node in the device-tree to work around this issue.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable the 'i2c edid' command to query and display data from an attached
HDMI monitor of LVDS display with an EDID device.
Example:
Ventana > i2c dev 2 && i2c edid 0x50
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add support for the USB mass storage gadget to enable access to on-board
storage.
Example:
Ventana > ums 0 mmc 0 # provide ums access to the uSD
Ventana > ums 0 usb 0 # provide ums access to the first USB device
Ventana > ums 0 sata 0 # provide ums access to an mSATA device
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 Datasheets specifies that when the IMX6 LDO is enabled
(internal Anatop LDO's for VDD_ARM, VDD_SOC, and VDD_xPU) you need to
provide 1350mV on VDD_ARM_IN and VDD_SOC_IN for IMX6Q@1GHz (Automotive)
and 1275mV for IMX6DL@800MHz (Industrial). While we are still about 50mV
shy on the IMX6Q operating at 1GHz we set it to the max we can and leave it
up to the kernel to implement a regulator driver for the LTC3676 and put
the LDO's in bypass mode which allows us to drop the voltages by 125mV
respectively.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The GW52xx has a MUX that can direct front-panel USB OTG to one of the
miniPCIe sockets (for use with a cellular modem for example). Use hwconfig
to steer this.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks Ventana boards don't all use IMX6 FEC, so lets define default
ethprime based off the first detected device.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
I've encountered issues when using 4k packets through certain switches. For
now disable this and go back to using MTU size packets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add 'fdt_fixup_display' function to fixup device-tree native-mode property
of display-timings node to select timings for a specific display.
This is useful if a device-tree has configurations for multiple
display timings for undetectable displays.
see kernel Documentation/devicetree/bindings/video/display-timing.txt
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Simon Glass <sjg@chromium.org>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.
The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.
The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch
Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.
This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
On SoCFPGA, using "sf update" with an non-4byte aligned length leads
to a hangup (and reboot via watchdog). This is because of the unaligned
access in the cadence QSPI driver which is hard to prevent since the
data is written into a 4-byte wide FIFO. This patch fixes this problem
by changing the behavior of the last sector write (not sector aligned).
The new code is even simpler and copies the source data into the temp
buffer and now uses the temp buffer to write the complete sector. So
only one SPI sector write is used now instead of 2 in the old version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Fix typos and too big #ifdef.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed the unnecessary error check from spi_xfer
as the bitlen zero is possible now to deassert the
chip select for which no data is required to be transfered.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Correct the macros as per insertion of array fast read
command CMD_READ_ARRAY_FAST in spi_read_cmds_array in file
sf_probe.c
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds description for NOR flash layout (firmware images)
in the README file for LS2085A platforms.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. LS2085a provides PCIE_LUT_DBG register rather than PCIE_LDBG
to show the link status, so the patch fixes it.
2. Increase the delay time to make sure that link training
has finished.
3. Return invalid value when accessing multi-function device
4. For LS2085a DBI_RO_WR_EN bit is cleared as default, so we
must set this bit before change DBI register value.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following affected SOCs and their personalities for USB
Erratum A007792 :
T1040 Rev 1.1
T1024 Rev 1.0
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On QDS board with DDR4 DIMM, LPUART is used as console
output to verify DCU driver. This patch adds
ls1021aqds_ddr4_nor_lpuart_defconfig for this support.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale LS1021ATWR share some pins. Hwconfig option is used to
allows users to choose the pin functions.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
