Commit graph

2099 commits

Author SHA1 Message Date
Stefan Roese
4d2ca9d6a0 cfi_flash: Use flash_read32() in sector_erased()
The function sector_erased() is modified to not use pointer
access, but to use the correct accessor functions. This fixes a
problem on the t3corp board with the Xilinx DS617 flash chips. Here
a board specific accessor function is needed to read from flash
in 32bit mode. This patch enables such an operation mode.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:54:10 +01:00
Stefan Roese
df4e813b72 cfi_flash: Fix problems with status/id read mode
This patch adds some calls to set the flash chip in the read-status-
register- or read-id-mode before the corresponding register is
read back. This problem was detected while porting the common CFI
driver to support the Xilinx DS617 flash chips.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:54:03 +01:00
John Schmoller
9fd84915a9 fsl_upm: Add MxMR/MDR synchronization
According to Freescale reference manuals (eg section "13.4.4.2
Programming the UPMs" of the P4080 Reference Manual):

"Since the result of any update to the MxMR/MDR register must be in
effect before the dummy read or write to the UPM region, a write to
MxMR/MDR should be followed immediately by a read of MxMR/MDR."

The UPM on a custom P4080-based board did not work without performing
a read of MxMR/MDR after a write.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-13 09:32:15 -06:00
David Müller (ELSOFT AG)
2111cb44a7 fix s3c2410_nand timing default values
The attached patch fixes wrong timing default values and adds the
possibility to specify board specific timing value in the board config file.

Signed-off-by: David Mueller <d.mueller@elsoft.ch>
2010-12-06 18:28:48 -06:00
Anatolij Gustschin
34bbb8fb46 cfi_flash: fix bug introduced while recent change to flash_get_size()
commit ec50a8e389
"cfi_flash: handle 'chip size exceeds address window' situation"
added 3rd argument to flash_get_size() but didn't fix all the
function calls from the board specific code. Many boards have
their own flash_get_size() definitions in the board code and
use them there, but some boards (e.g. tqm834x, tqm85xx, pdm360ng)
use flash_get_size() from the cfi_flash.c driver.

The bug shows up if the value of the "max_size" argument (which
is not defined when calling the function with two arguments)
happens to be less than "info->size". In this case on the
affected boards we end up with a bank of reduced size and
in the worst case might even be not able to update U-Boot or
to boot the kernel from flash:

=> fli

Bank # 1: CFI conformant FLASH (32 x 16)  Size: 0 kB in 1 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 4096 ms, write timeout: 1 ms
  Buffer write timeout: 3 ms, buffer size: 64 bytes

  Sector Start Addresses:
  F0000000   RO

Bank # 2: CFI conformant FLASH (32 x 16)  Size: 128 MB in 512 Sectors
  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x227E
  Erase timeout: 4096 ms, write timeout: 1 ms
  Buffer write timeout: 3 ms, buffer size: 64 bytes

  Sector Start Addresses:
  F8000000        F8040000        F8080000        F80C0000        F8100000
  F8140000        F8180000        F81C0000        F8200000        F8240000
  ...

E.g., updating U-Boot is not possible now:

=> protect off ${u-boot_addr} +${u-boot_size}
Error: end address (0xf007ffff) not in flash!
Bad address format
=> era ${u-boot_addr} +${u-boot_size}
Error: end address (0xf007ffff) not in flash!
Bad address format

This patch removes the 3rd argument of flash_get_size() again
and sets "max_size" in the function itself instead of passing
it as a function argument.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-11-28 19:41:11 +01:00
Stefan Roese
c5d02825ae ppc4xx/NAND: Reduce size of NAND SPL image
This is needed for the canyonlands_nand build target. Without it
the resulting image won't fit into 4k.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-11-27 23:35:09 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Reinhard Meyer
e0987e251f sf: ramtron: new spi fram driver
Supports most types that support Read-Id and the FM25H20.

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-11-10 04:26:18 -05:00
Wolfgang Denk
17dd883c5b Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-10-29 21:47:48 +02:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
C Nauman
d9abba8254 Add generic support for samsung s3c2440
This patch adds generic support for the Samsung s3c2440 processor.

Global s3c24x0 changes to struct members converting from upper case to
lower case.

Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-10-28 15:35:56 +09:00
Ilya Yanok
ec50a8e389 cfi_flash: handle 'chip size exceeds address window' situation
On some boards we have flash mapped high in the address space with
considerably small window (say 0xFE000000 and 32MB). When we install
bigger chip (say 64MB) on such a board strange things happen
(flash_write() doesn't work at all, for ex). That's because cfi_flash
driver doesn't care about window size at all.
Of course, cleanest solution would probably be to just extend address
window to be able to map the whole flash but for legacy/compatibility
reasons some people prefer just truncate the flash size and never use
the upper part.
This patch adds an option for cfi_flash driver to handle this situation
properly. To achieve this we add the new function cfi_flash_bank_size()
which can be provided by the board code and weak-aliased to default
implementation that returns value from the CONFIG_SYS_FLASH_BANKS_SIZES
array if it's defined or 0 otherwise (the last case is added for
compatibility).
If non-zero flash bank size is provided and detected chip size is bigger
than provided address window size the warning will be displayed and
flash chip will be truncated.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>

Changed cfi_flash_bank_size() return type to unsigned long
to match caller function.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-23 21:04:49 +02:00
Ben Gardiner
10d6ac94e0 davinci_nand, trivial : use symbolic ECC start command
The ECC calculations were started by writing 1 << 13 to the nand FCR register;
that value is also defined as DAVINCI_NANDFCR_4BIT_CALC_START in emif_defs.h.

This patch substitutes the macro DAVINCI_NANDFCR_4BIT_CALC_START for the
magic number '1 << 13'.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-10-17 20:14:43 +02:00
Reinhard Meyer
0d3fe2b153 sf: turn probe switch into a lookup table
This allows for arbitrarily long manufacturer ids following the JEDEC
standard of 0x7f continuation bytes.  It also makes adding new entries
easier as it's just one element in an array.  The downside is that it
increases code size a bit, but we're talking ~50 bytes.

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-12 21:08:25 -04:00
Wolfgang Denk
c0c3590bb2 Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash 2010-10-12 20:49:27 +02:00
John Schmoller
0e3fa01a63 cfi_flash: Fix "Unknown FLASH" error message
When a CFI flash chip could not be detected an error message similar to
the following would be printed on bootup:

 FLASH: ## Unknown FLASH on Bank 1 - Size = 0x01000000 = 0 MB

The printf incorrectly converted the flash size into megabytes.  This
patch fixes the printing of the flash size in megabytes:

 FLASH: ## Unknown FLASH on Bank 1 - Size = 0x01000000 = 16 MB

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-10-12 08:59:15 +02:00
Enric Balletbo i Serra
456be17dbe mtd: OneNAND: add support for OneNAND manufactured by Numonyx
This patch adds the Numonyx manufacturer code (0x20) to
onenand manufacturers.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
2010-10-11 15:15:45 -05:00
Scott Wood
36650ca9f1 Followup fixes on the mtdparts spread patchset
Consolidate some code in mtd_get_len_incl_bad(), and fix a condition
where a valid partition could be reported as truncated if it has a
good block at the end of the device (unlikely, since the BBT is usually
there).

Fix mid-block declarations in net_part_size().

Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-11 15:11:01 -05:00
Ben Gardiner
4ba692fb1e mtd: add an mtd method for get_len_incl_bad()
The logic to 'spread' mtd partitions needs to calculate the length in
the mtd device, including bad blocks.

This patch introduces a new function, mtd_get_len_incl_bad that can
return both the length including bad blocks and whether that length
was truncated on the device. This new function will be used by the
mtdparts spread command later in this series. The definition of the
function is #ifdef'd out in configurations that do not use the new
'mtdparts spread' command.

Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
2010-10-11 15:11:00 -05:00
Scott Wood
5b8e6bb517 nand: remove dead code and suspend/resume
Get rid of the several "#if 0" sections that were keeping around Linux
code that isn't relevant to U-Boot.  Besides cluttering the code, these
sections make tracking upstream changes harder, rather than easier.
It's easy to discard obviously irrelevant diff hunks that patch rejects,
but it's not as easy to notice hunks that apply cleanly to the #if 0
section, but *are* relevant to U-Boot and require modification elsewhere.

Also remove suspend/resume, as this is not applicable to U-Boot.  Removal
saves 232 bytes on powerpc.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-11 15:10:35 -05:00
Scott Wood
3048632251 nand erase: .spread, .part, .chip subcommands
A while back, in http://lists.denx.de/pipermail/u-boot/2009-June/054428.html,
Michele De Candia posted a patch to not count bad blocks toward the
requested size to be erased.  This is desireable when you're passing in
something like $filesize, but not when you're trying to erase a partition.

Thus, a .spread subcommand (named for consistency with
http://lists.denx.de/pipermail/u-boot/2010-August/075163.html) is introduced
to make explicit the user's desire to erase for a given amount of data,
rather than to erase a specific region of the chip.

While passing $filesize to "nand erase" is useful, accidentally passing
something like $fliesize currently produces quite unpleasant results, as the
variable evaluates to nothing and U-Boot assumes that you want to erase
the entire rest of the chip/partition.  To improve the safety of the
erase command, require the user to make explicit their intentions by
using a .part or .chip subcommand.  This is an incompatible user interface
change, but keeping compatibility would eliminate the safety gain, and IMHO
it's worth it.

While touching nand_erase_opts(), make it accept 64-bit offsets and sizes,
fix the percentage display when erase length is rounded up, eliminate
an inconsistent warning about rounding up the erase length which only
happened when the length was less than one block (rounding up for $filesize
is normal operation), and add a diagnostic if there's an attempt to erase
beginning at a non-block boundary.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-11 15:10:17 -05:00
Scott Wood
f9a5254111 nand util: read/write: accept unaligned length
The underlying code in nand_base.c already supports non-page-aligned reads
and writes, but the block-skipping wrapper code did not.

With block skipping, an unaligned start address is not useful since you
really want to be starting at the beginning of a partition -- or at least
that's where you want to start checking for blocks to skip, but we don't
(yet) support that.  So we still require the start address to be aligned.

An unaligned length, though, is useful for passing $filesize to the
read/write command, and handling it does not complicate block skipping.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-11 15:09:23 -05:00
David Jander
ff0dc2c433 sf: spansion: add support for S25FL032P parts
This patch introduces an extra mask-field in spansion_spi_flash_params
to support flash chips with 1-byte extended ID (like the S25FL032P).

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06 20:50:38 -04:00
Marc-André Hébert
c3cb09207f sf: spansion: fixing erasing when sector size >64KiB
The spansion_erase currently only works when the sector size is 64KB.
cmd[1] should contain the higher 8 bit of the 24 bit address of the
sector to be erased. Currently it is holding the sector index to be
erased which happens to be the same thing when the sector size is
64KB.

Signed-off-by: Marc-Andre Hebert <marc-andre.hebert@humanware.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06 20:50:38 -04:00
Graeme Smecher
74f9e0d8a0 sf: winbond: add support W25Q64 parts
Adds support for Winbond's W25Q64 SPI flash. These devices are used on
(among others) Xilinx' SP601 and SP605 Spartan-6 evaluation boards.
Tested with "sf" commands.

Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06 03:34:10 -04:00
Wolfgang Denk
2e6e1772c0 Merge branch 'next' of /home/wd/git/u-boot/next
Conflicts:
	include/ppc4xx.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-28 23:30:47 +02:00
Karl Beldan
86af10cac4 Fix "ubi part" cmd re-entrancy
Commit 2ee951ba (UBI: Enable re-initializing of the "ubi part" command)
reset mtd_devs in ubi_exit() but missed ubi_init()'s failure path.

Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-27 15:06:00 +02:00
Stefan Roese
b36df56115 ppc4xx: Move ppc4xx headers to powerpc include directory
This patch moves some ppc4xx related headers from the common include
directory (include/) to the powerpc specific one
(arch/powerpc/include/asm/). This way to common include directory is not
so cluttered with files.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23 09:02:05 +02:00
Stefan Roese
3c29975e94 cfi_flash: Remove uneccessary #ifdef CONFIG_SYS_MAX_FLASH_BANKS_DETECT
Now that the defines are moved to header files we don't need this
conditional compilation any more. Remove it.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-20 15:09:00 +02:00
Stefan Roese
ca5def3f30 cfi_flash: Simplify dynamic flash bank number detection
This patch simplifies the use of CONFIG_SYS_MAX_FLASH_BANKS_DETECT. By
moving these optional variables and defines into the common code, board
specific code is minimized. Currently only the following board use
this feature:

APC405, IDS8247, TQM834x

And IDS8247 doesn't seem to really need this feature, since its not
updating the bank number variable at all. So this patch removes the
definition of CONFIG_SYS_MAX_FLASH_BANKS_DETECT from this board port.

This new framework will be used by the upcoming lwmon5 update as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-09-20 15:08:51 +02:00
Stefan Roese
b00e19cc6b cfi_flash: Add weak default for cfi_flash_bank_addr()
cfi_flash_bank_addr(int bank_nr) returns the base addresses of the
requested bank. Introducing this weak default enables boards to override
this functions with a board specific version when required.

This feature will be used in the lwmon5 board update, supporting runtime
detection of 2 board revisions with different flash layouts.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-20 15:08:43 +02:00
Stefan Roese
cba34aafde cfi_flash: Simplify flash_get_info()
This patch removes an unecessary check in the return statement. This is
not needed, since "info" is initializes to NULL. And "info" will not be
written to again, if the flash address is not found.

Additionally "info" is not initialized to "0" but to "NULL".

Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-20 15:08:33 +02:00
Wolfram Sang
1075b07e2c nand/davinci: make sure ECC calculation has really started
Due to a register glitch (result code <4 might show up right after the
start-calculation-bit was set), make sure the ECC has really started.

See 1c3275b656045aff9a75bb2c9f3251af1043ebb3 in the kernel.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-13 14:43:05 -05:00
Wolfgang Denk
a78ded1311 Merge branch 'master' of git://git.denx.de/u-boot-ti 2010-09-09 19:55:02 +02:00
Steve Sakoman
4c468397cf mtd: nand: supress 'unknown NAND' warning if no nand is found
This printk was added recently and results in ugly output on systems
with no NAND:

NAND:  nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x00, Chip ID: 0x00 0 MiB

instead of:

NAND:  0 MiB

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08 14:51:29 -04:00
Wolfgang Denk
09b4a9cf40 Merge branch 'master' of git://git.denx.de/u-boot-samsung 2010-09-08 00:03:22 +02:00
Minkyu Kang
889a275d42 ARMV7: S5P: rename from CONFIG_S5PC1XX to CONFIG_S5P
Use the same configuration around S5P SoCs.
(s5pc100, s5pc110, s5pc210 and so on)

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-08-26 17:33:23 +09:00
Philippe De Muyter
54652991ca Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips.
I have "ported" U-boot to a in house made board with Numonyx Axcell P33/P30
256-Mbit 65nm flash chips.

After some time :( searching for bugs in our board or soft, we have
discovered that those chips have a small but annoying bug, documented in
"Numonyx Axcell P33/P30 256-Mbit Specification Update"

It states :
When customer uses [...] block unlock, the block lock status might be
altered inadvertently. Lock status might be set to either 01h or 03h
unexpectedly (00h as expected data), which leads to program/erase failure
on certain blocks.

A working workaround is given, which I have applied and tested with success :

Workaround:  If the interval between 60h and its subsequent command
	     can be guaranteed within 20us, Option I is recommended,
	     otherwise Option II (involves hardware) should be selected.
Option I: The table below lists the detail command sequences:
Command
	      Data bus           Address bus       Remarks
Sequence
  1              90h            Block Address
						   Read Lock Status
  2             Read         Block Address + 02h
 (2)(3)                                      (1)
3                60h           Block Address
 (2)(3)                                      (1)   Lock/Unlock/RCR Configuration
4           D0h/01h/03h        Block Address
Notes:
(1) Block Address refers to RCR configuration data only when the 60h
    command sequence is used to set RCR register combined with 03h
    subsequent command.
(2) For the third and fourth command sequences, the Block Address must
    be the same.
(3) The interval between 60h command and its subsequent D0h/01h/2Fh/03h
    commands should be less than 20us.

And here is a log comparison of a simple (destructive) flash test without
and with the workaround.

 diff without-numonyx-workaround.log with-numonyx-workaround.log
 -U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:07:47)
 +U-Boot 2010.06-00696-g22b002c-dirty (Aug 16 2010 - 15:25:19)

  CPU:   Freescale MCF5484
         CPU CLK 200 MHz BUS CLK 100 MHz
  Board: Macq Electronique ME2060
  I2C:   ready
  DRAM:  64 MiB
  FLASH: 32 MiB
  In:    serial
  Out:   serial
  Err:   serial
  Net:   FEC0, FEC1
  -> flinfo

  Bank # 1: CFI conformant FLASH (16 x 16)  Size: 32 MB in 259 Sectors
    Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8922
    Erase timeout: 4096 ms, write timeout: 1 ms
    Buffer write timeout: 5 ms, buffer size: 1024 bytes

    Sector Start Addresses:
    FE000000 RO   FE008000 RO   FE010000 RO   FE018000 RO   FE020000 RO
    FE040000 RO   FE060000 RO   FE080000 RO   FE0A0000 RO   FE0C0000 RO
    ...
    FFF80000 RO   FFFA0000 RO   FFFC0000 RO   FFFE0000 RO
  -> protect off all
  Un-Protect Flash Bank # 1
  ................... done
  -> erase all
  Erase Flash Bank # 1
  ................... done
  -> cp.b 1000000 fe000000 2000000
 -Copy to Flash... Flash not Erased
 +Copy to Flash... done
  ->

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18 09:09:00 +02:00
Stefan Roese
70084df712 cfi_flash: Cleanup flash_print_info()
This patch does the following:

- Extract code to detect if sector is erased into function
  sector_erased().
- Because of this, we don't have variable declarations inside the
  sector loop in flash_print_info()
- Change "return" to "break" in the "if (ctrlc()) statement:
  This fixes a problem with the resulting output. Before this
  patch the output was:

  Sector Start Addresses:
  FC000000        FC020000        FC040000   =>

  With this patch it is now:

  Sector Start Addresses:
  FC000000        FC020000        FC040000
  =>

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2010-08-18 09:09:00 +02:00
Philippe De Muyter
d77c7ac47e Fix printing & reading of 16-bit CFI device identifiers
Fix reading and printing of CFI flashes 16-bit devices identifiers

Nowadays CFI flashes have a 16-bit device identifier.  U-boot still
print them and read them as if they were only 8-bit wide.  Fix that.
Before:
  Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x1B
After:
  Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x881B

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18 09:09:00 +02:00
Kim Phillips
2e97394a6d cfi_flash: flinfo: allow user interrupt in flash print info fn
flashes getting larger, users more impatient.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-08-18 09:09:00 +02:00
Wolfgang Denk
cdb749778a Rename getenv_r() into getenv_f()
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function.  This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).

Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.

To avoid confusion, rename into getenv_f() [as "running from flash"]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-08-04 00:45:36 +02:00
Becky Bruce
f51cdaf191 83xx/85xx/86xx: LBC register cleanup
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers.  Merge
this into a single spot.

To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.

In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.

I have done a successful ppc build all and tested a board or two from
each processor family.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Wolfgang Denk
cb8f031729 Merge branch 'master' of git://git.denx.de/u-boot-blackfin 2010-07-14 21:54:45 +02:00
Mike Frysinger
253f47f3a7 Blackfin: bfin_nand: convert to portmux framework
Rather than bang MMRs directly, use the new portmux framework to handle
the details.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
2010-07-13 17:50:49 -04:00
Mike Frysinger
bc1a884686 mtd: nand_plat: add simple GPIO framework DEV_READY option
Make it easy to use GPIOs for the DEV_READY pin by using the common GPIO
framework.  Also make the NAND_PLAT_INIT() define optional.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-07-08 16:52:12 -05:00
Florian Fainelli
1445f6ffd5 NAND: add Toshiba TC58NVG0 identifier
The Toshiba TC58NVG0* parts are 128Mbytes x 8 bits 3.3V parts with the 0xD1
identifier. Add these to the list of known devices IDs.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2010-07-08 16:49:50 -05:00
Florian Fainelli
3e9b349c7f NAND: show manufacturer and device ID for unknown chips
When the NAND part is not supported, it is useful to show the manufacturer
and device ID to help debugging and reporting.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2010-07-08 16:49:50 -05:00
Mike Frysinger
b376bbb49f sf: move useful messages from debug to printf
At the moment, the default SPI flash subsystem is quite terse.  Errors and
successes both result in a generic message.  So move the useful errors and
useful successes to printf output by default.

While we're here, also convert the messages to use print_size().

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-06-30 23:47:08 -04:00
Thomas Chou
12c2e3bbbe spi_flash: support old STMicro parts with RES
Some old STMicro parts do not support JEDEC ID (0x9f). This patch
uses RES (0xab) to get Electronic ID and translates it to JEDEC ID.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2010-06-30 23:47:08 -04:00
Peter Horton
ceeba00308 UBI: initialise update marker
UBI: initialise update marker

The in kernel copy of a volume's update marker is not initialised from the
volume table. This means that volumes where an update was unfinnished will
not be treated as "forbidden to use". This is basically that the update
functionality was broken.

Signed-off-by: Peter Horton <zero@colonel-panic.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefan Roese <sr@denx.de>
2010-06-23 00:00:05 +02:00
Andrew Caldwell
c941b77adc Blackfin: nand: drain the write buffer before returning
The current Blackfin nand write function fills up the write buffer but
returns before it has had a chance to drain.  On faster systems, this
isn't a problem as the operation finishes before the ECC registers are
read, but on slower systems the ECC may be incomplete when the core tries
to read it.

So wait for the buffer to drain once we're done writing to it.

Signed-off-by: Andrew Caldwell <Andrew.Caldwell@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-26 17:59:13 -05:00
Stefan Roese
1b1f9a9d00 UBI: Ensure that "background thread" operations are really executed
The current U-Boot UBI implementation is copied from Linux. In this
porting the UBI background thread was not handled correctly. Upon write
operations ubi_wl_flush() makes sure, that all queued operations, like
page-erase, are completed. But this is missing for read operations.

This patch now makes sure that such operations (like scrubbing upon
bit-flip errors) are not queued, but executed directly.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-05-19 10:57:19 +02:00
Albin Tonnerre
f852a0c3bf drivers/mtd/spi/eeprom_m95xxx.c: add missing error checking
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2010-04-09 23:05:54 +02:00
Thomas Chou
22d6c8faac cfi_flash: reset timer in flash status check
This patch adds reset_timer() before the flash status check
waiting loop.

Since the timer is basically running asynchronous to the cfi
code, it is possible to call get_timer(0), then only a few
_SYSCLK_ cycles later an interrupt is generated. This causes
timeout even though much less time has elapsed. So the timer
period registers should be reset before get_timer(0) is
called.

There is similar usage in nand_base.c.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-04-07 11:33:16 +02:00
Wolfgang Denk
0020db3f0d Merge remote branch 'origin/master' into next 2010-03-29 12:33:43 +02:00
Wolfgang Denk
0d41ad7edc Merge branch 'next' of git://www.denx.de/git/u-boot-cfi-flash into next 2010-03-29 12:33:16 +02:00
Thomas Chou
e5720823f6 cfi flash: add status polling method for amd flash
This patch adds status polling method to offer an alternative to
data toggle method for amd flash chips.

This patch is needed for nios2 cfi flash interface, where the bus
controller performs 4 bytes read cycles for a single byte read
instruction. The data toggle method can not detect chip busy
status correctly. So we have to poll DQ7, which will be inverted
when the chip is busy.

This feature is enabled with the config def,
CONFIG_SYS_CFI_FLASH_STATUS_POLL

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-26 11:35:50 +01:00
Renato Andreola
c40c94a3d2 cfi_flash: precision and underflow problem in tout calculation
With old configuration it could happen tout=0 if CONFIG_SYS_HZ<1000.

Signed-off-by: Renato Andreola <renato.andreola@imagos.it>
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-25 09:44:58 +01:00
Nikolay Petukhov
7c27b7b1ea at91: add hwecc method for nand
This is a patch to use the hardware ECC controller of
the AT91SAM9260 for the AT91 nand. Taken from the kernel 2.6.33.

Signed-off-by: Nikolay Petukhov <Nikolay.Petukhov@gmail.com>
2010-03-23 14:29:09 -05:00
Cyril Chemparathy
cc41a59a74 TI: Davinci: NAND Driver Cleanup
Modified to use IO accessor routines consistently.  Eliminated volatile usage
to keep checkpatch.pl happy.

Signed-off-by: Cyril Chemparathy <cyril@ti.com>
2010-03-23 14:29:09 -05:00
Thomas Weber
5647f78d04 mod change 755 => 644 for multiple files
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'

Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-21 22:22:53 +01:00
Wolfgang Denk
93910edb59 Prepare v2010.03-rc1
Coding style cleanup, update CHANGELOG.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-03-12 23:06:04 +01:00
Wolfgang Wegner
8f9a221045 ] fix monitor protection for CONFIG_MONITOR_IS_IN_RAM
For platforms with flash below ram addresses, the current check to
activate monitor protection is wrong/insufficient. This patch fixes
CONFIG_MONITOR_IS_IN_RAM for these systems by adding a check for
this configuration.

Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-03-04 10:07:12 +01:00
Wolfgang Denk
08254a1a97 Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash 2010-02-03 20:15:46 +01:00
Ladislav Michl
f3dec798d9 CFI: fix eraseregions numblocks
eraseregions numblocks was sometimes one less than actual, possibly producing
erase regions with zero blocks. As MTD code touches eraseregions only if
numeraseregions is greater that zero, allocate eraseregions only for non
uniform erase size flash.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-02-02 08:22:00 +01:00
John Rigby
b081c2e9b9 Nand mxc_nand add v1.1 controller support
Add support for version 1.1 of the nfc nand flash
controller which is on the i.mx25 soc.

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Scott Wood <scottwood@freescale.com>
2010-01-27 14:22:41 -06:00
Vipin KUMAR
165fa406ad SPEAr : nand driver support for SPEAr SoCs
SPEAr SoCs contain an FSMC controller which can be used to interface
with a range of memories eg. NAND, SRAM, NOR.
Currently, this driver supports interfacing FSMC with NAND memories

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Vipin KUMAR
a6e34f76c5 SPEAr : smi driver support for SPEAr SoCs
SPEAr SoCs contain a serial memory interface controller. This
controller is used to interface with spi based memories.
This patch adds the driver for this IP.

Signed-off-by: Vipin <vipin.kumar@st.com>
2010-01-23 08:15:49 -06:00
Magnus Lilja
c4832dffff MXC: Add large page oob layout for i.MX31 NAND controller.
Import the large page oob layout from Linux mxc_nand.c driver.

The CONFIG_SYS_NAND_LARGEPAGE option is used to activate
the large page oob layout. Run time detection is not supported
as this moment.

This has been tested on the i.MX31 PDK board with a large
page NAND device.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-01-19 17:08:13 -06:00
Magnus Lilja
f6a9748e32 mxc_nand: Update driver to work with i.MX31.
Tested on i.MX31 Litekit.

Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-01-19 17:08:13 -06:00
Wolfgang Denk
2ff6922280 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-01-12 23:47:03 +01:00
Nick Thompson
20da6f4d93 Davinci: davinci_nand.c performance enhancments
Introduces various optimisations that approximately triple the
read data rate from NAND when run on da830evm.

Most of these optimisations depend on the endianess of the machine
and most of them are very similar to optimisations already present
in the Linux Kernel.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2010-01-06 16:11:16 -06:00
Nick Thompson
26be2c53d6 Davinci: NAND enable ECC even when not in NAND boot mode
Davinci: NAND enable ECC even when not in NAND boot mode

On Davinci platforms, the default NAND device is enabled (for ECC)
in low level boot code when NAND boot mode is used. If booting in
another mode, NAND ECC is not enabled. The driver should make
sure ECC is enabled regardless of boot mode if NAND is configured
in U-Boot.

Signed-off-by: Nick Thompson <nick.thompson@ge.com>
2010-01-04 08:48:17 -06:00
Nick Thompson
97f4eb8cfb Davinci: Configurable NAND chip selects
Davinci: Configurable NAND chip selects

Add a CONFIG_SYS_NAND_CS setting to all davinci configs and
use it to setup the NAND controller in the davinci_nand
mtd driver.

Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
2010-01-04 08:48:17 -06:00
Wolfgang Denk
bb3bcfa242 Merge branch 'next' of ../next 2009-12-15 23:38:34 +01:00
Stefan Roese
f4cfe42758 nand: Fix access to last block in NAND devices
Currently, the last block of NAND devices can't be accessed. This patch
fixes this issue by correcting the boundary checking (off-by-one error).

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
2009-12-11 13:11:57 -06:00
Heiko Schocher
4b142febff common: delete CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.

Signed-off-by: Heiko Schocher <hs@denx.de>
2009-12-08 22:14:07 +01:00
Wolfgang Denk
206c00f26f Merge branch 'master' into next
Conflicts:
	lib_generic/zlib.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 22:47:17 +01:00
Daniel Hobi
0ec81db202 Fix computation in nand_util.c:get_len_incl_bad
Depending on offset, flash size and the number of bad blocks,
get_len_incl_bad may return a too small value which may lead to:

1) If there are no bad blocks, nand_{read,write}_skip_bad chooses the
bad block aware read/write code. This may hurt performance, but does
not have any adverse effects.

2) If there are bad blocks, the nand_{read,write}_skip_bad may choose
the bad block unaware read/write code (if len_incl_bad == *length)
which leads to corrupted data.

Signed-off-by: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
2009-12-07 22:38:16 +01:00
Wolfgang Denk
2a49bf3149 Merge branch 'master' into next
Conflicts:
	board/esd/plu405/plu405.c
	drivers/rtc/ftrtc010.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-05 02:11:59 +01:00
kevin.morfitt@fearnside-systems.co.uk
ac67804fbb Add a unified s3c24x0 header file
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
Minkyu Kang
47e801bec3 s3c64xx: move s3c64xx header files to asm-arm/arch-s3c64xx
This patch moves the s3c64xx header files from include/
to include/asm-arm/arch-s3c64xx

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:13 -06:00
kevin.morfitt@fearnside-systems.co.uk
492fb1fdbc Move s3c24x0 header files to asm-arm/arch-s3c24x0/
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.

checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:

ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch

As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.

The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:

WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8	S3C24X0_REG8;
+typedef volatile u16	S3C24X0_REG16;
+typedef volatile u32	S3C24X0_REG32;

I'll fix these errors in another patch.

Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-11-27 16:26:12 -06:00
Mike Frysinger
fcffb680e7 sf: fix stmicro offset setup while erasing
Reported-by: Peter Gombos <gombos@protecta.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-11-22 23:56:36 +01:00
Jason McMullan
d394a77950 sf: new driver for Winbond W25X16/32/64 devices
Signed-off-by: Jason McMullan <jason.mcmullan@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-11-22 23:54:18 +01:00
Sandeep Paulraj
10a5a79912 NAND: Add Support for 4K page size in DaVinci NAND driver
This patch adds support for NAND devices with a page size of
4K in the DaVinci NAND driver. The layout matches the layout that TI uses
for 4K page size NAND devices in the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-20 13:15:38 -06:00
Hui.Tang
5e1ded558b S3C2410 NAND Flash Add Missing Function
This patch add nand_read_buf() for S3C2410 NAND SPL.
In nand_spl/nand_boot.c, nand_boot() will check nand->select_chip,
so nand->select_chip should also be initialized.

Signed-off-by: Hui.Tang <zetalabs@gmail.com>
2009-11-18 14:30:13 -06:00
Sandeep Paulraj
6cd752f927 NAND: Update read_read_subpage API check
This patch updates a check condition in the NAND driver.
The check condition is similat to what is in linux/next.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-18 14:26:40 -06:00
Amul Kumar Saha
cacbe91958 Flex-OneNAND driver support
This patch adds support for Flex-OneNAND devices.

Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
2009-11-13 16:56:18 -06:00
Mingkai Hu
35209cbcee fsl_elbc_nand: remove the bbt descriptors relocation fixup
The commit 66372fe2 manually relocated the bbt pattern pointer,
which can be removed by using full relocation.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
2009-11-13 16:56:18 -06:00
David Brownell
7e86661cd7 NAND: fix "raw" reads with ECC syndrome layouts
The syndrome based page read/write routines store ECC, and possibly other
"OOB" data, right after each chunk of ECC'd data.  With ECC chunk size of
512 bytes and a large page (2KiB) NAND, the layout is:

  data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover

Where OOBx is (prepad, ECC, postpad).  However, the current "raw" routines
use a traditional layout -- data OOB, disregarding the prepad and postpad
values -- so when they're used with that type of ECC hardware, those calls
mix up the data and OOB.  Which means, in particular, that bad block
tables won't be found on startup, with data corruption and related chaos
ensuing.

The current syndrome-based drivers in mainline all seem to use one chunk
per page; presumably they haven't noticed such bugs.

Fix this, by adding read/write page_raw_syndrome() routines as siblings of
the existing non-raw routines; "raw" just means to bypass the ECC
computations, not change data and OOB layout.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-11-13 16:56:17 -06:00
Sandeep Paulraj
5df3c2b62c NAND: Don't walk past end of oobfree[]
When computing oobavail from the list of free areas in the OOB,
don't assume there will always be an unused slot at the end.
This syncs up with the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:16 -06:00
Sandeep Paulraj
18b5a4b43a NAND: Update check condition for nand_read_page_hwecc API
The patch updates the check condition for determining
whether the ECC corrections has failed.
This makes it similar to what is in the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:16 -06:00
Sandeep Paulraj
e25ee03962 NAND: Updating comments/explanations in the NAND driver
Patch updates the comments and explanations for
the arguments to various functions.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:16 -06:00
Sandeep Paulraj
aad4a28b25 NAND: Subpage shift for ecc_steps equal to 16
This was originally part of Thomas Gleixner's patch for
adding support for 4KiB pages.
This is not part of the U-Boot NAND driver so updating the
driver with this to sync up with the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:15 -06:00
Sandeep Paulraj
36e0b98ec8 NAND: Remove commented out code
Patch removes already commented out dead code

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:15 -06:00
Sandeep Paulraj
4f41e7ea1a NAND: Correct the "chip_shift" calculation
This patch updates the "chip_shift" calculation in the
NAND driver. This is being done to sync up the NAND driver with
the kernel NAND driver.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-13 16:56:15 -06:00
Sandeep Paulraj
aaa8eec532 NAND: Update to support 64 bit device size
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-11-13 16:56:14 -06:00
Stefan Roese
fa36ae790e cfi: Add weak default function for flash_cmd_reset()
Currently the CFI driver issues both AMD and Intel reset commands.
This is because the driver doesn't know yet which chips are connected.
This dual reset seems to cause problems with the M29W128G chips as
reported by Richard Retanubun. This patch now introduces a weak default
function for the CFI reset command, still with both resets. This can
be overridden by a board specific version if necessary.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
2009-10-28 11:34:14 +01:00
Mike Frysinger
4166ee58d3 sf: add GPL-2 license info
Some of the new spi flash files were missing explicit license lines.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-10-24 22:44:18 +02:00
kevin.morfitt@fearnside-systems.co.uk
3d1988ab47 Clean-up of s3c24x0 nand driver
This patch re-formats the arm920t s3c24x0 nand driver in preparation for changes
to add support for the Embest SBC2440-II Board.

The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports

It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
 - patches 1/4, 2/4 and 3/4 of this series

Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-10-13 21:13:57 -05:00
Minkyu Kang
4678d674f0 s5pc1xx: support onenand driver
This patch includes the onenand driver for s5pc100

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-10-13 21:13:55 -05:00
Peter Tyser
521af04d85 Conditionally perform common relocation fixups
Add #ifdefs where necessary to not perform relocation fixups.  This
allows boards/architectures which support relocation to trim a decent
chunk of code.

Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-10-03 10:17:57 +02:00
Scott Wood
d44e9c1736 NAND: davinci: Fix warnings when 4-bit ECC not used
I accidentally left v2 of "NAND: DaVinci:Adding 4 BIT ECC support"
applied when I pushed the tree last merge window, and missed these fixes
which were in v3 of that patch.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-09-28 16:33:18 -05:00
Paul Gibson
d3f4941874 mpc512x. Micron nand flash needs a reset before a read command is issued.
Micron nand flash needs a reset before a read command is issued.
The current mpc5121_nfc driver ignores the reset command.
2009-09-22 22:59:42 +02:00
Stefan Roese
d1c3b27525 ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:

- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
  user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines

Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-09-11 10:35:58 +02:00
Scott Wood
cfcbf8c4cf mxc_nand: Remove Freescale's "All Rights Reserved."
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-09-04 23:03:10 +02:00
Sandeep Paulraj
77b351cd0f NAND: DaVinci: V2 Adding 4 BIT ECC support
This patch adds 4 BIT ECC support in the DaVinci NAND
driver. Tested on both the DM355 and DM365.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Sandeep Paulraj
f83b7f9e8a MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRST
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips.  This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.

This patch has been accepted by Andrew Morton and can be found at

http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Ilya Yanok
36fab997d8 mxc_nand: add nand driver for MX2/MX3
Driver for NFC NAND controller found on Freescale's MX2 and MX3
processors. Ported from Linux. Tested only with i.MX27 but should
works with other MX2 and MX3 processors too.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Sandeep Paulraj
a2c65b47ef NAND: ADD page Parameter to all read_page/read_page_raw API's
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs.  The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.

This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch

WE would like this to become part of the u-boot GIT as well

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Heiko Schocher
de4250929f 83xx, kmeter1: added NAND support
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Kyungmin Park
ecad289fc6 OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Matthias Kaehlcke
403ce1f759 KB9202: Add NAND support
Add KB9202 NAND driver

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:01 -05:00
Niklaus Giger
3a7b2c21fb Support up to 7 banks for ids as specified in JEDEC JEP106Z
see http://www.jedec.org/download/search/jep106Z.pdf
Add some second source legacy flash chips 256x8.

Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-26 08:58:27 +02:00
Feng Kan
68e74567cf ppc4xx: Fix ECC Correction bug with SMC ordering for NDFC driver
Fix ECC Correction bug where the byte offset location were double
flipped causing correction routine to toggle the wrong byte location
in the ECC segment. The ndfc_calculate_ecc routine change the order
of getting the ECC code.
        /* The NDFC uses Smart Media (SMC) bytes order */
        ecc_code[0] = p[2];
        ecc_code[1] = p[1];
        ecc_code[2] = p[3];
But in the Correction algorithm when calculating the byte offset
location, the s1 is used as the upper part of the address. Which
again reverse the order making the final byte offset address
location incorrect.
	byteoffs = (s1 << 0) & 0x80;
	.
	.
	byteoffs |= (s0 >> 4) & 0x08;
The order is change to read it in straight and let the correction
function to revert it to SMC order.

Signed-off-by: Feng Kan <fkan@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-25 17:41:42 +02:00
Jean-Christophe PLAGNIOL-VILLARD
a3c5057a6c eeprom_m95xxx: remove unused variable i
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-08-21 23:36:19 +02:00
Giulio Benetti
1fc1d9aed0 add WATCHDOG_RESET() on nand write and read
Signed-off-by: giulio.benetti@micronovasrl.com
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-21 22:55:21 +02:00
John Schmoller
7dedefdf74 flash: Fix CFI buffer size bug
Fix bug introduced by 9c048b5234.

The cfi_flash.c driver cast the flash buffer size to a uchar in
flash_write_cfibuffer(). On some flash parts, (tested on Numonyx
part PC32F512M29EWH), the buffer size is 1KB. Remove the cast to
uchar to enable buffer sizes to be larger.

Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-08-13 09:28:20 +02:00
Albin Tonnerre
3ac374c0f0 Add driver for the ST M95xxx SPI EEPROM
This chip is used in a number of boards manufactured by Calao-Systems
which should be supported soon. This driver provides the necessary
spi_read and spi_write functions necessary to communicate with the chip.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-08-09 23:45:14 +02:00
Dirk Behme
894113529e omap3: replace all instances of gpmc config struct by one global
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:34:11 +02:00
Dirk Behme
97a099eaa4 omap3: remove typedefs for configuration structs
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-08-08 11:33:23 +02:00
Matthias Ludwig
187af954cf omap3: embedd gpmc_cs into gpmc config struct
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html

Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
2009-08-07 23:31:51 +02:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Stefan Roese
f2f376ab95 nand: ndfc: Remove unnecessary #ifdef's
Now that the 4xx NAND driver ndfc is moved to the common NAND driver
directory we don't need this #ifdef's anymore.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:03 -05:00
Stefan Roese
12582ac771 nand/ppc4xx: Move PPC4xx NAND driver to common NAND driver directory
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:02 -05:00
Valeriy Glushkov
3ebf70db54 nand: fixed failed reads on corrected ECC errors in nand_util.c
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Paulraj, Sandeep <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:01 -05:00
David Brownell
ed727d394c Typo fix: use CONFIG_SOC_DM644X, not CONFIG_SOC_DM646.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:01 -05:00
Kim Phillips
9578718c1b mtd: cfi - if defined, use MAX_FLASH_BANKS_DETECT for static declarations
a.k.a cfi_mtd.c does as cfi_flash.c does.  This also prevents
the TQM834x build from doing a:

cfi_mtd.c:36: error: variably modified 'cfi_mtd_info' at file scope
cfi_mtd.c:37: error: variably modified 'cfi_mtd_names' at file scope

using gcc 4.4.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-16 15:27:45 +02:00
Wolfgang Denk
c3ae126c2c Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-07-13 23:45:02 +02:00
Po-Yu Chuang
b4db4a7638 issue write command to base for JEDEC flash
For JEDEC flash, we should issue word programming command relative to
base address rather than sector base address. Original source makes
SST Flash fails to program sectors which are not on the 0x10000 boundaries.

e.g.
SST39LF040 uses addr1=0x5555 and addr2=0x2AAA, however, each sector
is 0x1000 bytes.

Thus, if we issue command to "sector base (0x41000) + offset(0x5555)",
it sends to 0x46555 and the chip fails to recognize that address.

This patch is tested with SST39LF040.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-13 11:01:31 +02:00
Prafulla Wadaskar
205a0988d8 nand: Add Marvell Kirkwood NAND driver
This patch adds a NAND driver for the Marvell Kirkwood SoC's

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2009-07-08 21:20:10 +02:00
Mingkai Hu
66372fe2ab fsl_elbc_nand: redirect the pointer of bbt pattern to RAM
The bbt descriptors contains the pointer to the bbt pattern which
are statically initialized memory struct. When relocated to RAM,
these pointers will continue point to NOR flash(or L2 SRAM, or
other boot device). If the contents of NOR flash changed or L2
SRAM disabled, it'll hang the system.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:10 -05:00
kevin.morfitt@fearnside-systems.co.uk
98713d2663 Bug-fix in drivers mtd nand Makefile
The S3C2410 NAND driver source file is included in the makefile instead of
the object file.

Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:09 -05:00
Jean-Christophe PLAGNIOL-VILLARD
378adfcdf4 mtd: nand: use loff_t for offset
nand_util currently uses size_t which is arch dependent and not always a
unsigned long.  Now use loff_t, as does the linux mtd layer.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:06 -05:00
Mike Frysinger
cd84423a09 mtd: nand: new base driver for memory mapped nand devices
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped.  Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:04 -05:00
David Brownell
154b5484ac davinci_nand chipselect/init cleanup
Update chipselect handling in davinci_nand.c so that it can
handle 2 GByte chips the same way Linux does:  as one device,
even though it has two halves with independent chip selects.
For such chips the "nand info" command reports:

  Device 0: 2x nand0, sector size 128 KiB

Switch to use the default chipselect function unless the board
really needs its own.  The logic for the Sonata board moves out
of the driver into board-specific code.  (Which doesn't affect
current build breakage if its NAND support is enabled...)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:03 -05:00
David Brownell
6e29ed8e57 davinci_nand: cleanup II (CONFIG_SYS_DAVINCI_BROKEN_ECC)
Remove CONFIG_SYS_DAVINCI_BROKEN_ECC option.  It's not just nasty;
it's also unused by any current boards, and doesn't even match the
main U-Boot distributions from TI (which use soft ECC, or 4-bit ECC
on newer chips that support it).

DaVinci GIT kernels since 2.6.24, and mainline Linux since 2.6.30,
match non-BROKEN code paths for 1-bit HW ECC.  The BROKEN code paths
do seem to partially match what MontaVista/TI kernels (4.0/2.6.10,
and 5.0/2.6.18) do ... but only for small pages.  Large page support
is really broken (and it's unclear just what software it was trying
to match!), and the ECC layout was making three more bytes available
for use by filesystem (or whatever) code.

Since this option itself seems broken, remove it.  Add a comment
about the MV/TI compat issue, and the most straightforward way to
address it (should someone really need to solve it).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:58:01 -05:00
David Brownell
fcb7747775 davinci_nand: cleanup I (minor)
Minor cleanup for DaVinci NAND code:

 - Use I/O addresses from nand_chip; CONFIG_SYS_NAND_BASE won't
   be defined when there are multiple chipselect lines in use
   (as with common 2 GByte chips).

 - Cleanup handling of EMIF control registers
    * Only need one pointer pointing to them
    * Remove incorrect and unused struct supersetting them

 - Use the standard waitfunc; we don't need a custom version

 - Partial legacy cleanup:
    * Don't initialize every board like it's a DM6446 EVM
    * #ifdef a bit more code for BROKEN_ECC

Sanity checked with small page NAND on dm355 and dm6446 EVMs;
and large page on dm355 EVM (packaged as two devices, not one).

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-07 17:44:55 -05:00
Wolfgang Denk
a48ecc969f Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	drivers/spi/Makefile

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-07 22:22:05 +02:00
Wolfgang Denk
37572cde7f Merge branch 'master' of git://git.denx.de/u-boot-ubi 2009-07-07 20:58:30 +02:00
Stefan Roese
d318d0c44d UBI: Fix build problem noticed on Apollon (arm/testing repo)
This patch fixes a build problem noticed on Apollon by using
mtd_dev_by_eb() instead of "/" as done in the Linux UBI version.
So this brings the U-Boot UBI version more in sync with the Linux
version again.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-07-07 16:33:44 +02:00
Prafulla Wadaskar
2efee52b09 sf: Macronix additional chips supported
new chips supported:-
MX25L1605D, MX25L3205D, MX25L6405D, MX25L12855E
out of which MX25L6405D and MX25L12855E tested on Kirkwood platforms

Modified the Macronix flash support to use 2 bytes of device id instead of 1
This was required to support MX25L12855E

Signed-off-by: Piyush Shah <spiyush@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-06 18:46:20 -04:00
Mike Frysinger
dd54126715 sf: sst: add sst25vf###b ids
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-06 18:46:20 -04:00
Mike Frysinger
7d907f0ea9 sf: sst: fix sector size
Looks like when I was encoding the sector sizes, I forgot to divide by 8
(due to the stupid marketing driven process that declares all sizes in
useless megabits and not megabytes).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-06 18:46:20 -04:00
Thomas Lange
d583ef5147 ARM DaVinci: EMIF settings
NAND module should not modify EMIF registers unrelated to CS2
that is used for NAND, i.e. do not modify EWAIT config register
or registers for other Chip Selects.

Without this patch, EMIF configurations made in board_init()
will be invalidated.

Signed-off-by: Thomas Lange <thomas@corelatus.se>
2009-07-06 21:52:23 +02:00
Stefan Roese
35f2edbb6c nand/mpc512x: Add MPC512x NAND support (NFC)
This patch adds NAND Flash Controller driver for MPC5121 revision 2.
All device features, except hardware ECC and power management, are
supported.

This NFC driver replaces the one orignally posted by John Rigby:

"[PATCH] Freescale NFC NAND driver"

It's a port of the Linux driver version posted by Piotr Ziecik a few
weeks ago. Using this driver has the following advantages (from my
point of view):

- Compatibility with the Linux NAND driver (e.g. ECC usage)
- Better code quality in general
- Resulting U-Boot image is a bit smaller (approx. 3k)
- Better to sync with newer Linux driver versions

The only disadvantage I can see, is that HW-ECC is not supported right
now. But this could be added later (e.g. port from Linux driver after
it's supported there). Using HW-ECC on the MCP5121 NFC has a general
problem because of the ECC usage in the spare area. This collides with
JFFS2 for example.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
2009-06-12 20:47:19 +02:00
Stefan Roese
60cfe87bd3 UBI: Add compile-time check for correct malloc area configuration
UBI is quite memory greedy and requires at least approx. 512k of malloc
area. This patch adds a compile-time check, so that boards will not
build with less memory reserved for this area (CONFIG_SYS_MALLOC_LEN).

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:47:18 +02:00
Prafulla Wadaskar
7ce6031afc sf: new Macronix MX25xx SPI flash driver
Added macronix SF driver for MTD framework
MX25L12805D is supported and tested
TBD: sector erase implementation, other deivces support

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-06-12 20:47:18 +02:00
Todor I Mollov
2a6cc58869 sf: atmel: implement power-of-two write/erase funcs
Signed-off-by: Todor I Mollov <tmollov@ucsd.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-06-12 20:47:18 +02:00
Stefan Roese
d558107c18 mtd: Introduce CONFIG_MTD_DEVICE to select compilation of mtdcore.o
This new define enables mtdcore.c compilation and with this we can
select the MTD device infrastructure needed for the reworked mtdparts
command.

We now have the 2 MTD infrastructure defines, CONFIG_MTD_DEVICE and
CONFIG_MTD_PARTITIONS. CONFIG_MTD_DEVICE is needed (as explained above)
for the "mtdparts" command and CONFIG_MTD_PARTITIONS is needed for UBI.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
2009-06-12 20:45:47 +02:00
Stefan Roese
8d2effea23 mtd: Update MTD infrastructure to support 64bit device size
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
2009-06-12 20:45:47 +02:00
Stefan Roese
0a57265533 mtd: Add MTD concat support to concatenate multiple MTD NOR devices
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:45:47 +02:00
Wolfgang Denk
dfcd7f2160 Redundant Environment: protect full sector size
Several boards used different ways to specify the size of the
protected area when enabling flash write protection for the sectors
holding the environment variables: some used CONFIG_ENV_SIZE and
CONFIG_ENV_SIZE_REDUND, some used CONFIG_ENV_SECT_SIZE, and some even
a mix of both for the "normal" and the "redundant" areas.

Normally, this makes no difference at all. However, things are
different when you have to deal with boards that can come with
different types of flash chips, which may have different sector
sizes.

Here we may have to chose CONFIG_ENV_SECT_SIZE such that it fits the
biggest sector size, which may include several sectors on boards using
the smaller sector flash types. In such a case, using CONFIG_ENV_SIZE
or CONFIG_ENV_SIZE_REDUND to enable the protection may lead to the
case that only the first of these sectors get protected, while the
following ones aren't.

This is no real problem, but it can be confusing for the user -
especially on boards that use CONFIG_ENV_SECT_SIZE to protect the
"normal" areas, while using CONFIG_ENV_SIZE_REDUND for the
"redundant" area.

To avoid such inconsistencies, I changed all sucn boards that I found
to consistently use CONFIG_ENV_SECT_SIZE for protection. This should
not cause any functional changes to the code.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Paul Ruhland
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Stefan Roese <sr@denx.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Dave Ellis <DGE@sixnetio.com>
Acked-by: Stefan Roese <sr@denx.de>
2009-06-04 00:16:16 +02:00
Stefan Roese
dba6fcf651 cfi_mtd: Fix bug in last sector detection
This patch now enabled this cfi-mtd wrapper to correctly detect and
erase the last sector in an NOR FLASH device.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-03 23:45:27 +02:00
Stefan Roese
f40f6db278 nand: Fix problem with ECC ordering for PPC4xx NDFC platforms
This patch enables Smart Media (SMC) ECC byte ordering which is used
on the PPC4xx NAND FLASH controller (NDFC). Without this patch we have
incompatible ECC byte ordering to the Linux kernel NDFC driver.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2009-05-23 12:51:39 +02:00
Stefan Roese
f8e2b3107e MTD: Change cfi-mtd to accept non-uniform sector sizes
With this patch non-uniform NOR FLASH chips (chips with multiple erase
regions) can be exported via the cfi-mtd layer and therefor used by UBI.
We select the largest sector size as erasesize. The cfi driver will make
sure that the smaller sectors are handled correctly.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-29 11:06:06 +02:00
Stefan Roese
dbe29e36a4 mtd: nand/onenand: Register mtd device upon device scanning
With this patch the NAND and OneNAND devices are registered in the MTD
subsystem and can then be referenced by the mtdcore code (e.g.
get_mtd_device_nm()). This is needed for the new "ubi part" command
syntax without the flash type parameter (nor|nand|onenand).

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-28 01:15:38 +02:00
Stefan Roese
10bb62d85a mtd: nand: Include linux/mtd/partitions.h in nand_base.h
This patch removes this compilation warning when CONFIG_MTD_PARTITIONS is
defined:

nand_base.c: In function 'nand_release':
nand_base.c:2922: warning: implicit declaration of function 'del_mtd_partitions'

Signed-off-by: Stefan Roese <sr@denx.de>
2009-04-28 01:15:37 +02:00
David Brownell
7732cef2ee CMD_UBI != MTD_PARTITIONS
Fix dependency goofage:  it should certainly be possible to have the
partition support without bringing in UBI commands.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Stefan Roese <sr@denx.de>
2009-04-16 23:03:27 +02:00
Graf Yang
a343ba87ea Blackfin: nand: flush peripheral before polling it
We need to make sure the data written to the nand flash controller makes
it there before we start polling its status register.  Otherwise, we may
get stale data and return before the controller is actually ready.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Scott Wood <scottwood@freescale.com>
2009-04-06 17:37:37 -04:00
Andreas Huber
c203ef5db0 UBI/cfi-mtd: Fix mtd name for multiple chips
On platforms with multiple NOR chips, currently only the first one
can be selected using the "ubi part" command. This patch fixes this
problem by using different names for the NOR "mtd devices".

It also changes the name of the NOR MTD device from "cfi-mtd" to
"norX" (X indexing the device numer) to better match the mtdparts
defaults.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
2009-04-04 23:25:40 +02:00
Ulf Samuelsson
cb82a53266 Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Wolfgang Denk
8ddfe804c4 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-04-03 22:48:05 +02:00
Scott Wood
99067b08f4 Noisily disable the legacy NAND subsystem.
Legacy NAND is marked for feature removal after April 2009 (i.e. this
upcoming release).  There are still several boards that reference it
(though many do so only for disk-on-chip support which has been silently
disabled for a while now).  These boards will now fail to build
with #error, though the code is still there if the user removes #error.

The plan is to remove the code outright in the next release, along with
any board code that refers to it (such as board/esd/common/auto_update.c).

Also, remove the legacy NAND API description from README.nand.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-04-03 15:27:26 -05:00
Mike Frysinger
d9596ffbdc sf: stmicro: dont send 4 bytes when reading status register
I can't find anywhere in the datasheet that says the status register needs
3 dummy bytes sent to it before being able to read back the first real
result.  Tests on a Blackfin board show that after writing the opcode, the
status register starts coming back immediately.  So only write out the
read status register opcode before polling the result.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-04-02 12:51:28 -04:00
Mike Frysinger
1abe365ffc sf: set common timeouts in seconds, not milliseconds
Since timeouts are only hit when there is a problem in the system, we
don't want to prematurely timeout on a functioning setup.  Thus having
low timeouts (in milliseconds) doesn't gain us anything in the production
case, but rather increases likely hood of causing problems where none
otherwise exist.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-02 08:11:31 -04:00
Mike Frysinger
2a6ce1115b sf: stmicro: use common page timeout define
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-02 06:51:55 -04:00
Mike Frysinger
0dcdbb172c sf: always read 5 bytes for the idcode
Some SPI flash drivers like to have extended id information available
(like the spansion flash), so rather than making it re-issue the ID cmd
to get at the last 2 bytes, have the common code read 5 bytes rather than
just 3.  This also matches the Linux behavior where it always reads 5 id
bytes from all flashes.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Mingkai Hu <Mingkai.hu@freescale.com>
2009-04-02 06:50:21 -04:00
Mike Frysinger
9726ba4aba sf: stmicro: drop redundant id read
The common SPI flash code reads the idcode and passes it down to the SPI
flash driver, so there is no need to read it again ourselves.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
CC: Jason McMullan <mcmullan@netapp.com>
CC: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2009-04-02 06:50:17 -04:00
Mike Frysinger
1c5874374e sf: add driver for SST flashes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-02 06:49:58 -04:00
Mike Frysinger
f773a1bbdb sf: drop DEBUG defines
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-04-02 06:49:49 -04:00
Jean-Christophe PLAGNIOL-VILLARD
6b850a9fa8 mtd: add some at45 spi flash support
- AT45DB321D
 - AT45DB161D
 - AT45DB081D
 - AT45DB041D
 - AT45DB021D
 - AT45DB011D

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:49:38 -04:00
Mingkai Hu
6805e4bf83 mtd: SPI Flash: Support the Spansion Flash
Add MTD SPI Flash support for S25FL008A, S25FL016A,
S25FL032A, S25FL064A, S25FL128P.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-04-02 06:49:30 -04:00
Jean-Christophe PLAGNIOL-VILLARD
b3f66b0ba0 s3c2410: move nand driver to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30 18:58:40 +02:00
Jean-Christophe PLAGNIOL-VILLARD
ee4f3e2765 davinci: move nand driver to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-30 18:58:39 +02:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Wolfgang Grandegger
33846df28f Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:40 -05:00
Wolfgang Grandegger
06e9f7df05 Add support for TQM-specific chip select logic to FSL-UPM
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:39 -05:00
Wolfgang Grandegger
e93c1c169d Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:38 -05:00
Wolfgang Grandegger
672ed2aee9 Enable multi chip support in the NAND layer
This patch adds support for NAND_MAX_CHIPS to the MTD NAND layer.
Multi-chips devices are displayed as shown:

  Device 0: 2x NAND 512MiB 3,3V 8-bit, sector size 128 KiB

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:37 -05:00
Eric Schumann
3a3baf3ee6 Make flash protection work, when the environment is in EEPROM
On the pcm030 the environment is located in the onboard EEPROM. But we want
to handle flash sector protection in a safe manner. So we must read the
unlock environment variable from EEPROM instead from flash.

This patch is required as long the evironment is saved into the EEPROM.

Stefan: Additional change as suggested by Wolfgang, use bigger char array
(instead of 4).

Signed-off-by: Eric Schumann <E.Schumann@phytec.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-23 09:50:45 +01:00
Jean-Christophe PLAGNIOL-VILLARD
74c076d6c3 at91sam9/at91cap: move nand drivers to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:24 +01:00
Richard Retanubun
7a88601a34 CFI: geometry reversal for STMicro M29W320DT
Follow up to the flash_fixup_stm to fix geometry reversal
on STMicro M29W320ET flash chip. The M29W320DT has 4 erase region.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-03-19 15:00:32 +01:00
Jean-Christophe PLAGNIOL-VILLARD
0176c03a24 nomadik/nand: fix 'ecc512' discards qualifiers from pointer target type
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-02-22 17:56:50 +01:00
Alessandro Rubini
0d8c6eab24 Nand driver for Nomadik SoC
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).

Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
2009-02-22 13:40:28 +01:00
Heiko Schocher
4f975678de cfi: make flash_get_info() non static
If on your board is more than one flash, you must know
the size of every single flash, for example, for updating
the DTS before booting Linux. So make this function
flash_get_info() extern, and you can have all info
about your flashes.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-11 17:01:17 +01:00
Wolfgang Denk
f8306cb94f Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master 2009-02-07 23:51:52 +01:00
Wolfgang Denk
64ace0d1e5 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2009-02-07 23:37:10 +01:00
Peter Tyser
8da601280a NAND: Add timeout for reset command
Without the timeout present an infinite loop can occur if the
NAND device is broken or not present.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-02-06 17:29:38 -06:00
Peter Tyser
10dc6a9bef NAND: Silence warning when CONFIG_SYS_NAND_QUIET_TEST
Commit cfa460adfd removed support
for disabling the "No NAND device found!!!" warning when
CONFIG_SYS_NAND_QUIET_TEST was defined.  This re-adds support
for silencing the warning.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-02-06 17:29:29 -06:00
Valeriy Glushkov
ad09ab2e3a NAND: Fixed invalid pointers to static relocated chip names
Dear Wolfgang,

You are right, the patch was ugly.
The new one seems to be better.

Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-02-06 17:28:31 -06:00
Stefan Roese
e1fb6d0d52 cfi_flash: Fix typo in cfi_flash.c
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small typo and compilation warning for systems with CFI
legacy support (e.g. hcu4). This patch fixes it.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-05 11:44:52 +01:00
Stefan Roese
28745db969 jedec_flash: Only use manufacturer defines from common flash.h
This patch removes the double defined manufacturer defines from
jedec_flash.c. Since the common defines in flash.h are 32bit
we now need the (16) cast. This patch also removes the compilation
warning (e.g. seen on hcu5):

./MAKEALL hcu5
Configuring for hcu5 board...
jedec_flash.c:219: warning: large integer implicitly truncated to unsigned type

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-05 11:27:58 +01:00
Stefan Roese
ec21d5cfcb cfi_flash: Silence compilation warning
Patch "flash/cfi_flash: Use virtual sector start address, not phys"
introduced a small compilation warning. This patch fixes it.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-05 11:25:57 +01:00
Becky Bruce
09ce9921a7 flash/cfi_flash: Use virtual sector start address, not phys
include/flash.h was commented to say that the address in
flash_info->start was a physical address.  However, from u-boot's
point of view, and looking at most flash code, it makes more
sense for this to be a virtual address.  So I corrected the
comment to indicate that this was a virtual address.

The only flash driver that was actually treating the address
as physical was the mtd/cfi_flash driver.  However, this code
was using it inconsistently as it actually directly dereferenced
the "start" element, while it used map_physmem to get a
virtual address in other places.  I changed this driver so
that the code which initializes the info->start field calls
map_physmem to get a virtual address, eliminating the need for
further map_physmem calls.  The code is now consistent.

The *only* place a physical address should be used is when defining the
flash banks list that is used to initialize the flash_info struct,
usually found in the board config file.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-02-05 11:20:05 +01:00
Wolfgang Denk
657f2062d8 Fix compiler warning
(shows up only when DEBUG is enabled)

Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-02-04 12:09:20 +01:00
Mike Frysinger
be9d8c780e Blackfin: add driver for on-chip NAND controller
This is a port of the Linux Blackfin on-chip NFC driver to U-Boot.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-02-02 12:27:07 -05:00
Wolfgang Denk
6c6e042ab3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2009-02-01 21:38:07 +01:00
Richard Retanubun
e8eac43718 CFI: Add geometry reversal for STMicro M29W320ET
Added flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip.

Modeled after flash_fixup_amd, this patch handles the geometry reversal
or erase sectors that exist for ST Micro (now Numonyx) M29W320ET flash.
Since I cannot test all STM's chips, the detection is implemented as
narrow as possible for now.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26 10:59:48 +01:00
Jens Gehrlein
0f8e851e89 CFI: increase performance of function find_sector()
Tested on TQM5200S-BD with Samsung K8P2815UQB

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26 10:50:13 +01:00
Jens Gehrlein
a7292871a7 CFI: avoid redundant function call in single word programming mode
The function find_sector() doesn't need to be called twice in
the case of AMD command set.
Tested on TQM5200S-BD with Samsung K8P2815UQB.

Signed-off-by: Jens Gehrlein <sew_s@tqs.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26 10:49:59 +01:00
Dirk Behme
12201a1354 OMAP3: Add NAND support
Add NAND support.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24 17:51:21 +01:00
Brad Bozarth
68f8718df2 spi flash: fix crash due to spi flash miscommunication
Higher spi flash layers expect to be given back a pointer that was
malloced so that it can free the result, but the lower layers return
a pointer that is in the middle of the malloced memory. Reorder the
members of the lower spi structures so that things work out.

Signed-off-by: Brad Bozarth <bflinux@yumbrad.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-24 01:57:40 +01:00
Niklaus Giger
94f9279f7b Added legacy flash ST Micro M29W040B 2009-01-24 01:22:22 +01:00
Mike Frysinger
d4bade8d77 nand: fixup printf modifiers to match types used
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:52 -06:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Nishanth Menon
50657c2732 NAND: Enable nand lock, unlock feature
Enable nand lock, unlock and status of lock feature.
Not every device and platform requires this, hence,
it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK

Nand unlock and status operate on block boundary instead
of page boundary. Details in:
http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT

Intial solution provided by Vikram Pandita <vikram.pandita@ti.com>
Includes preliminary suggestions from Scott Wood

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:49 -06:00
Mike Frysinger
69fb8be4fc NAND: move board_nand_init to nand.h
Rather than putting the function prototype for board_nand_init() in the one
place where it gets called, put it into nand.h so that every place that also
defines it gets the prototype.  Otherwise, errors can go silently unnoticed
such as using the wrong return value (void rather than int) when defining
the function.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:49 -06:00
Stefan Roese
1ae3986204 OneNAND: Additional sync with 2.6.27
- Add subpage write support
- Add onenand_oob_64/32 ecclayout

This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:48 -06:00
Kyungmin Park
1714f51a20 Add markbad function
Add missing markbad function
If not, it's hang when it entered the mtd->mark_bad().

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-23 10:32:47 -06:00
Stefan Roese
8cf11f3aa7 OneNAND: Save version_id in onenand_chip struct
The version (ver_id) was not stored in the onenand_chip structure and
because of this the continuous locking scheme could be enabled on some
chips.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-23 10:32:46 -06:00
Stefan Roese
4fca3310d6 OneNAND: Fix compiler warnings
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-23 10:32:45 -06:00
Kyungmin Park
ef0921d6b0 Sync with 2.6.27
Sync with OneNAND kernel codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-23 10:32:44 -06:00
Wolfgang Denk
f85cd46918 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-12-30 23:30:47 +01:00
Kumar Gala
9d94aff699 NAND FSL elbc: Use virt_to_phys to determine which bank is in use
The current code that determines which bank/chipselect is used for a
given NAND instance only worked for 32-bit addresses and assumed
a 1:1 mapping.  This breaks in 36-bit physical configs.

The proper way to handle this is to use the virt_to_phys() and
BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address
with the the virtual address the NAND code uses.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Scott Wood <scottwood@freescale.com>
2008-12-19 18:20:08 -06:00
Scott Wood
ff49ea8977 NAND: Mark the BBT as scanned prior to calling scan_bbt.
Otherwise, recursion can occur if scan_bbt does not find a bad block
table, and tries to write one, and the attempt to erase the BBT area
causes a bad block check.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-12-16 14:40:34 -06:00
Wolfgang Denk
455ae7e87f Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 01:02:17 +01:00
Mike Frysinger
84bc72d90c spi/stmicro: fix debug() display of cmd
The stmicro_wait_ready() func tries to show the actual opcode that was sent
to the device, but instead it displays the array pointer.  Fix it to pull
out the opcode from the start of the array.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-12-16 00:48:18 +01:00
Stefan Roese
8173293516 UBI: Return -ENOMEM upon failing malloc
Return with correct error code (-ENOMEM) from ubi_attach_mtd_dev() upon
failing malloc().

Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10 12:55:23 +01:00
Stefan Roese
2ee951ba2a UBI: Enable re-initializing of the "ubi part" command
With this patch now, the user can call "ubi part" multiple times to
re-connect the UBI device to another MTD partition.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-09 10:07:36 +01:00
Stefan Roese
9def12cae3 MTD: Fix problem based on non-working relocation (list head mtd_partitions)
Don't use LIST_HEAD() but initialize the struct via INIT_LIST_HEAD() upon
first call of add_mtd_partitions(). Otherwise this won't work on platforms
where the relocation is broken (like MIPS or PPC).

Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-09 10:07:23 +01:00
Ilko Iliev
bd876772ee mtd/dataflash.c: fix a problem with the last partition
This patch fix the problem that only the [NB_DATAFLASH_AREA - 1] dataflash
partition can be defined to use the area to the end of dataflash size.
Now it is possible to have only one dataflash partition from 0 to the end
of of dataflash size.

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2008-12-02 21:53:24 +01:00
Ilko Iliev
03f797793b fix some coding style violations.
This patch fix some coding style violations.

Signed-off-by: Ilko Iliev <iliev@ronetix.at>
2008-12-02 21:53:22 +01:00
Scott Wood
2077e348c2 NAND: Fix misplaced return statement in nand_{read,write}_skip_bad().
This caused the operation to be needlessly repeated if there were
no bad blocks and no errors.

Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-11-25 10:47:02 -06:00
Wolfgang Denk
f9b354faa0 Merge branch 'master' of git://git.denx.de/u-boot-ubi 2008-11-25 11:40:57 +01:00
Piotr Ziecik
e6a7edbc17 mtd: Remove a printf() from add_mtd_device().
Remove a printf() from add_mtd_device(), which produces spurious output.

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-24 11:29:53 +01:00
Piotr Ziecik
91809ed51d cfi-mtd: Add cfi-mtd driver.
Add cfi-mtd driver, which exports CFI flash to MTD layer.
This allows CFI flash devices to be used from MTD layer.

Building of the new driver is controlled by CONFIG_FLASH_CFI_MTD
option. Initialization is done by calling cfi_mtd_init() from
flash_init().

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-24 11:05:25 +01:00
Piotr Ziecik
6ea808efdf cfi_flash: Add interface for flash verbosity control
Add interface for flash verbosity control. It allows
to disable output from low-level flash API. It is useful
when calling these low-level functions from context other
than flash commands (for example the MTD/CFI interface
implmentation).

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-24 10:55:36 +01:00
Piotr Ziecik
ebc9784ce6 cfi_flash: Export flash_sector_size() function.
Export flash_sector_size() function from drivers/mtd/cfi_flash.c,
so that it can be used in the upcoming cfi-mtd driver.

Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-24 10:55:35 +01:00
Stefan Roese
45aa5a7f4d cfi_flash: Make all flash access functions weak
This patch defines all flash access functions as weak so that
they can be overridden by board specific versions.

This will be used by the upcoming VCTH board support where the NOR
FLASH unfortunately can't be accessed memory-mapped. Special
accessor functions are needed here.

To enable this weak functions you need to define
CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS in your board config header.
Otherwise the "old" default functions will be used resulting
in smaller code.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-11-24 10:55:35 +01:00
Kyungmin Park
c91a719daa UBI: Add basic UBI support to U-Boot (Part 5/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
f412fefa07 UBI: Add basic UBI support to U-Boot (Part 4/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
2d262c4853 UBI: Add basic UBI support to U-Boot (Part 3/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
961df83361 UBI: Add basic UBI support to U-Boot (Part 2/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
f399d4a281 UBI: Add basic UBI support to U-Boot (Part 1/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
e29c22f5ab MTD: Add MTD paritioning infrastructure
This MTD part infrastructure will be used by the upcoming
UBI support.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Wolfgang Denk
9abda6ba73 CFI Driver: Fix "flash not ready" problem
This patch fixes a problem on systems where the NOR flash is attached
to a 64 bit bus.  The toggle bit detection in flash_toggle() is based
on the assumption that the same flash address is read twice without
any other interjacent flash accesses.  However, on 32 bit systems the
function flash_read64() [as currently implemented] does not perform
an atomic 64 bit read - instead, this is broken down into two 32 bit
read accesses on addresses "addr" and "addr + 4".  So instead of
reading a 64 bit value twice from "addr", we see a sequence of 4 32
bit reads from "addr", "addr + 4", "addr", and "addr + 4".  The
consequence is that flash_toggle() fails to work.

This patch implements a simple, but somewhat ugly solution, as it
avoids the use of flash_read64() in this critical place (by breaking
it down manually into 32 bit read operations) instead of rewriting
flash_read64() such to perform atomic 64 bit reads as one could
expect.  However, such a rewrite would require the use of floating
point load operations, which becomes pretty complex:

	save MSR;
	set Floating Point Enable bit in MSR;
	use "lfd" instruction to perform atomic 64 bit read;
	use "stfd" to store value to temporary variable on stack;
	load u64 value from temporary variable;
	restore saved MSR;
	return u64 value;

The benefit-cost ratio of such an implementation was considered too
bad to actually attempt this, especially as we can expect that such
an implementation would not only have a bigger memory footprint but
also cause a performance degradation.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-31 11:32:53 +01:00
Scott Wood
bd78bc6b2a NAND: Properly create JFFS2 cleanmarkers.
As reported by Ilko Iliev <iliev@ronetix.at>, the "nand erase clean"
command is currently broken, and among other things causes all blocks
to be marked bad.

This implements it properly using MTD_OOB_AUTO, along with some
indentation fixes.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 14:20:26 -05:00
Scott Wood
f7fe57c098 NAND fsl elbc: Set FMR[ECCM] based on page size.
Hardware expects ECCM 0 for small page and ECCM 1 for large page
when booting from NAND, so use those defaults.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 13:42:41 -05:00
Haiying Wang
4e190b03aa Make Freescale local bus registers available for both 83xx and 85xx.
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
  can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
  files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
  85xx can share them.

Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 11:12:53 -05:00
Karl Beldan
33efde5eca NAND: Reset chip on power-up
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.

Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 10:42:17 -05:00
Scott Wood
c45912d8ab NAND: sync with 2.6.27
This brings the core NAND code up to date with the Linux kernel.

Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.

I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 10:42:16 -05:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Jason Jin
fecb5ade3b Fix the NAND size overflow issue.
When the total size of all NAND devices exceeds 4 GiB, the size  will
overflow. This patch tries to fix this.

Note that we still have a problem when a single NAND device is bigger
than 4 GiB: then the overflow would actually happen earlier, i. e.
when storing the size in nand_info[].size, as nand_info[].size is an
"u_int32_t".

Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-10-14 13:27:16 +02:00
Ed Swarthout
0d01f66d23 CFI: cfi_flash write fix for AMD legacy
The flash_unlock_seq requires a sector for AMD_LEGACY.
Fix a retcode check typeo.

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-13 13:51:21 +02:00
Mike Frysinger
2215987e10 cfi_flash: do not reset flash when probe fails
The CFI flash driver starts at flash_init() which calls down into
flash_get_size().  This starts by calling flash_detect_cfi().  If said
function fails, flash_get_size() finishes by attempting to reset the
flash.  Unfortunately, it does this with an info->portwidth set to 0x10
which filters down into flash_make_cmd() and that happily smashes the
stack by sticking info->portwidth bytes into a cfiword_t variable that
lives on the stack.  On a 64bit system you probably won't notice, but
killing the last 8 bytes on a 32bit system usually leads to a corrupt
return address.  Which is what happens on a Blackfin system.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-02 10:30:32 +02:00
Wolfgang Denk
508eb85db7 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2008-09-13 01:45:56 +02:00
Anton Vorontsov
0008b6d968 fsl_elbc_nand: ecclayout cleanups
This patch deletes oobavail assignments, they're calculated by the nand
core code in nand_scan_tail, plus current oobavail values are wrong for
the LP NANDs.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-09-12 14:58:33 -05:00
Anton Vorontsov
8f42bf1c39 fsl_elbc_nand: implement support for flash-based BBT
This patch implements support for flash-based BBT for chips working
through ELBC NAND controller, so that NAND core will not have to re-scan
for bad blocks on every boot.

Because ELBC controller may provide HW-generated ECCs we should adjust
bbt pattern and bbt version positions in the OOB free area.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-09-12 14:57:20 -05:00
Anton Vorontsov
97ae023648 fsl_elbc_nand: fix OOB workability for large page NAND chips
For large page chips, nand_bbt is looking into OOB area, and checking
for "0xff 0xff" pattern at OOB offset 0. That is, two bytes should be
reserved for bbt means.

But ELBC driver is specifying ecclayout so that oobfree area starts at
offset 1, so only one byte left for the bbt purposes.

This causes problems with any OOB users, namely JFFS2: after first mount
JFFS2 will fill all OOBs with "erased marker", so OOBs will contain:

  OOB Data: ff 19 85 20 03 00 ff ff ff 00 00 08 ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
  OOB Data: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

And on the next boot, NAND core will rescan for bad blocks, then will
see "0xff 0x19" pattern, and will mark all blocks as bad ones.

To fix the issue we should implement our own bad block pattern: just one
byte at OOB start. Though, this will work only for x8 chips. For x16
chips two bytes must be checked. Since ELBC driver does not support x16
NANDs (yet), we're safe for now.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-09-12 14:56:03 -05:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Wolfgang Denk
f6808c48a5 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2008-09-10 11:07:35 +02:00
Andrew Klossner
5251469943 Fix printf errors under -DDEBUG
Fix printf format-string/arg mismatches under -DDEBUG.

These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx.  Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".

Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2008-09-09 17:02:41 -05:00
TsiChung Liew
7b7a869a8b mtd: SPI Flash: Support the STMicro Flash
Add MTD SPI Flash support for M25P16, M25P20, M25P32,
M25P40, M25P64, M25P80, M25P128.

Signed-off-by: Jason McMullan <mcmullan@netapp.com>
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
2008-09-09 11:57:29 -06:00
Graeme Russ
3ef96ded38 Update i386 code (sc520_cdp)
Attempt to bring i386 / sc520 inline with master

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2008-09-09 11:48:53 +02:00
Guennadi Liakhovetski
e0056b3410 NAND: add NAND driver for S3C64XX
Based on the original S3C64XX NAND driver by Samsung for U-Boot 1.1.6.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-08-31 00:39:47 +02:00
Wolfgang Denk
a49d10cf02 Minor coding style cleanup, updte CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-08-25 23:45:41 +02:00
Kyungmin Park
bfd7f38614 Fix OneNAND read_oob/write_oob functions compatability
Also sync with kernel OneNAND codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-21 13:50:20 -05:00
Nick Spence
9e8e63cce6 CFI: Add CFI_CMDSET_INTEL_EXTENDED to fix flash_real_protect()
This patch fixes a missing vendor code in the flash_real_protect() function.

Signed-off-by: Nick Spence <nick.spence@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-20 14:24:08 +02:00
TsiChung Liew
4e00acded2 CFI: Fix AMD Legacy sector protect
New implement sector lock and unlock or softlock commands
do not exist in AMD legacy flash. Thus, causing issue
when erasing AMD legacy flash (such as lv040)

Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-20 14:21:46 +02:00
Wolfgang Denk
855efd04e4 Merge branch 'master' of git://git.denx.de/u-boot-cfi-flash 2008-08-14 14:56:40 +02:00
Wolfgang Denk
4b0708093e Coding Style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-08-14 14:41:06 +02:00
Wolfgang Denk
28ac671910 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2008-08-14 11:26:22 +02:00
Stefan Roese
becbbc7b2a Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next 2008-08-14 08:25:13 +02:00
Kyungmin Park
d438d50848 Fix OneNAND build break
Since page size field is changed from oobblock to writesize. But OneNAND is not updated.
- fix bufferram management at erase operation
This patch includes the NAND/OneNAND state filed too.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-13 11:00:19 -05:00
Jean-Christophe PLAGNIOL-VILLARD
9483df6408 drivers/mtd/nand_legacy: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:43 +02:00
Jean-Christophe PLAGNIOL-VILLARD
cc4a0ceeac drivers/mtd/nand: Move conditional compilation to Makefile
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:43 +02:00
Jean-Christophe PLAGNIOL-VILLARD
4fb09b8192 drivers/mtd/onenand: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Jean-Christophe PLAGNIOL-VILLARD
00b1883a4c drivers/mtd: Move conditional compilation to Makefile
rename CFG_FLASH_CFI_DRIVER to CONFIG_FLASH_CFI_DRIVER

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:42 +02:00
Fathi BOUDRA
195ccfc599 OneNAND: Fill in MTD function pointers for OneNAND.
onenand_print_device_info():
 - Now returns a string to be placed in mtd->name,
   rather than calling printf.
 - Remove verbose parameter as it becomes useless.

Signed-off-by: Fathi Boudra <fabo@debian.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:32 -05:00
Marcel Ziswiler
eafcabd15f NAND: chip->state does not always get set.
Fixes an issue with chip->state not always being set causing troubles.

Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:29 -05:00
Ilya Yanok
13f0fd94e3 NAND: Scan bad blocks lazily.
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block.  This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:28 -05:00
Scott Wood
dfbf617ff0 NAND read/write fix
Implement block-skipping read/write, based on a patch from
Morten Ebbell Hestens <morten.hestnes@tandberg.com>.

Signed-off-by: Morten Ebbell Hestnes <morten.hestnes@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:28 -05:00
Anton Vorontsov
e1c3dbada3 nand: fsl_upm: convert to updated MTD NAND infrastructure
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:27 -05:00
Scott Wood
300253306a fsl_elbc_nand: Hard-code the FBAR/FPAR split.
The hardware has separate registers for block and page-within-block,
but the division between the two has no apparent relation to the
actual erase block size of the NAND chip.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:26 -05:00
Anton Vorontsov
9c814b0a71 fsl_elbc_nand: workaround for hangs during nand write
Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:26 -05:00
Scott Wood
9fd020d6b4 Freescale eLBC FCM NAND driver
This is a driver for the Flash Control Machine of the enhanched Local Bus
Controller found on some Freescale chips (such as the mpc8313 and the
mpc8379).

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:25 -05:00
Scott Wood
41ef8c716e Don't panic if a controller driver does ecc its own way.
Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.

The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:25 -05:00
Stefan Roese
e52b34d40a NAND: Make NAND driver less verbose per default
This patch turns off printing of bad blocks per default upon bootup.
This can always be shown via the "nand bad" command later.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-12 11:31:24 -05:00
Stefan Roese
1207226452 NAND: Change nand_wait_ready() to not call nand_wait()
This patch changes nand_wait_ready() to not just call nand_wait(),
since this will send a new command to the NAND chip. We just want to
wait for the chip to become ready here.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-12 11:31:22 -05:00
William Juul
5e1dae5c3d Fixing coding style issues
- Fixing leading white spaces
 - Fixing indentation where 4 spaces are used instead of tab
 - Removing C++ comments (//), wherever I introduced them

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:17 -05:00
William Juul
4cbb651b29 Remove white space at end.
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:16 -05:00
William Juul
cfa460adfd Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.

This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.

MAKEALL ppc/arm has some issues:
 * DOC/OneNand/nand_spl is not building (I have not tried porting
   these parts, and since I do not have any HW and I am not familiar
   with this code/HW I think its best left to someone else.)

Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
 cpu/ppc4xx/ndfc.c
 cpu/arm926ejs/davinci/nand.c
 board/delta/nand.c
 board/zylonite/nand.c

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:15 -05:00
Steve Sakoman
4d57b0fb29 OneNAND: Remove unused parameters to onenand_verify_page
The block and page parameters of onenand_verify_page() are not used. This causes a compiler error when CONFIG_MTD_ONENAND_VERIFY_WRITE is enabled.

Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2008-08-11 15:07:46 -05:00
Wolfgang Denk
dedec4cfc8 Merge branch 'master' of git://git.denx.de/u-boot-at91 2008-08-10 01:04:50 +02:00
Sergey Lapin
f77d92a3f5 DataFlash: AT45DB021 fix and AT45DB081 support
Fix for page size of AT45DB021. Also adding bigger AT45DB081
which comes with some newer boards.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-08-09 00:15:06 +02:00
Wolfgang Denk
2a112b234d CFI: allow for dynamically determined flash sizes and addresses
The CFI driver allowed only for static initializers in the
CFG_FLASH_BANKS_LIST definition, i. e. it did not allow to map
several flash banks contiguously if the bank sizes were not known in
advance, which kind of violates U-Boot's design philosophy.

(will be used for example by the TQM8xxL boards)

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-08-08 16:39:54 +02:00
Rafael Campos
bc9019e197 cfi-flash: Added support to flash_real_protect for Atmel flash devices
Some of the flash memories produced by ATMEL start in read-only mode.
We need to unprotect it. This patch allows the AT49BV6416 to work with
cfi_flash memories. Tested in the at91rm9200ek board.

Signed-off-by: Rafael Campos Las Heras <rafael.campos@hanscan.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:22:41 +02:00
Guennadi Liakhovetski
7949839e58 cfi-flash: Add definition for the AM29LV800BB AMD NOR-flash
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-08-06 14:19:06 +02:00
Haavard Skinnemoen
a229d291f3 spi flash: Fix printf() format warnings
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-23 16:15:01 +02:00
Sebastian Siewior
340ccb260f cfi_flash: fix flash on BE machines with CFG_WRITE_SWAPPED_DATA
This got broken by commits 93c56f212c
 [cfi_flash: support of long cmd in U-boot.]

That command needs to be in little endian format on BE machines
with CFG_WRITE_SWAPPED_DATA. Without this patch, the command 0xf0
gets saved on stack as 0x00 00 00 f0 and 0x00 gets written into
the cmdbuf in case portwidth = chipwidth = 8bit.

Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
2008-07-17 11:42:35 +02:00
Sebastian Siewior
7288f972fc cfi_flash: make the command u32 only
This got changed by commit 93c56f212c
[cfi_flash: support of long cmd in U-boot.]

Long is the wrong type because it will behave differently on 64bit
machines in a way that is probably not expected. u32 should be
enough.

Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
2008-07-15 21:42:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0a5676befb Fix some more printf() format issues.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-13 16:55:00 +02:00
Sergey Lapin
c6457e3b8b DataFlash AT45DB021 support
Some boards based on AT91SAM926X-EK use smaller DF chips to keep
bootstrap, u-boot and its environment, using NAND or other external
storage for kernel and rootfs. This patch adds support for
small 1024x263 chip.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
2008-07-10 22:50:28 +02:00
Stefan Roese
e870690bdc MTD/NAND: Fix printf format warning in nand code
This patch fixes NAND related printf format warning. Those warnings are
now visible since patch dc4b0b38d4
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-10 10:46:13 +02:00
Wolfgang Denk
40234535ee Merge branch 'master' of git://www.denx.de/git/u-boot-nand-flash 2008-07-10 00:59:04 +02:00
Scott Wood
3167c5386e NAND: Rename DEBUG to MTDDEBUG to avoid namespace pollution.
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-07-09 17:24:47 -05:00
Stefan Roese
0192d7d56e jedec_flash: Fix AM29DL800BB device ID
As pointed out by Jerry Hicks, this patch corrects the device ID of
the Spansion AM29DL800BB NOR device. Verified against latest Spansion
datasheet (rev C4 from Dezember 2006).

Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-08 12:57:14 +02:00
Stefan Roese
fb8c061ea0 cfi-flash: Fix problem in flash_toggle(), busy was not detected reliably
This patch simplifies flash_toggle() (AMD commandset), which is used to
detect if a FLASH device is still busy with erase/program operations. On
800MHz Canyonlands/Glacier boards (460EX/GT) the current implementation
did not detect the busy state reliably, resulting in non erased sectors
etc. This patch now simplifies this function by "just" comparing the
complete data-word instead of ANDing it with the command-word (0x40)
before the compatison. It is done the same way in the Linux implementation
chip_ready() in cfi_cmdset_0002.c.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-19 15:08:17 +02:00
Wolfgang Denk
1859e42fbf Merge branch 'master' of git://www.denx.de/git/u-boot-cfi-flash 2008-06-11 22:24:46 +02:00
Sergei Poselenov
248ae5cfc8 NAND: Added support for 128-bit OOB, adapted
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-06-11 00:30:22 -05:00
Wolfgang Grandegger
a75a57ef6e NAND FSL UPM: driver re-write using the hwcontrol callback
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:

- For the time being, the UPM setup writing the UPM array has been
  removed from the driver and must now be done by the board specific
  code.

- The bus width definition in "struct fsl_upm_nand" is now in bits to
  comply with the corresponding Linux driver and 8, 16 and 32 bit
  accesses are supported.

- chip->dev_read is only set if fun->dev_ready != NULL, which is
  required for boards not connecting the R/B pin.

- A few issue have been fixed with MxMR bit manipulation like in the
  corresponding Linux driver.

Note: I think the "io_addr" field of "struct fsl_upm" could be removed
      as well, because the address is already determined by
      "nand->IO_ADDR_[RW]", but I'm not 100% sure.

This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.

This patch is based on the following patches posted to this list a few
minutes ago:

  PPC: add accessor macros to clear and set bits in one shot
  83xx/85xx/86xx: add more MxMR local bus definitions

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-06-10 18:22:26 -05:00
Vasiliy Leoenenko
9c048b5234 cfi_flash: enable M18 flash chips family support.
Added new command set ID. Buffered write command processing is changed
in order to support M18 flash chips family.

Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
2008-06-03 21:02:34 +02:00
Vasiliy Leoenenko
93c56f212c cfi_flash: support of long cmd in U-boot.
Some NOR flash chips needs support of commands with length grether than max
value size of uchar. For example all M18 family chips use 0x1ff command in
buffered write mode as value of program loops count.

Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
2008-06-03 21:01:55 +02:00
Haavard Skinnemoen
d25ce7d24c SPI Flash subsystem
This adds a new SPI flash subsystem.

Currently, only AT45 DataFlash in non-power-of-two mode is supported,
but some preliminary support for other flash types is in place as
well.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-03 20:31:34 +02:00
Kumar Gala
f979690ee3 Fix warnings from gcc-4.3.0 build on a ppc host
* The cfi_flash.c memset fix actual allows the board to boot so there is
  a bit more going on here than just resolving warnings associated with
  uninitialized variables.

* include/asm/bitops.h:302: warning: '__swab32p' is static but used in
  inline function 'ext2_find_next_zero_bit' which is not static

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-03 19:52:52 +02:00
Dirk Behme
9723bbb46a nand: Correct NAND erase percentage output
For NAND erase sizes smaller than one NAND erase block, erase
percentage output becomes grater than 100% e.g.

-- cut --
  > nand info
Device 0: NAND 64MiB 1,8V 8-bit, sector size 16 KiB
  > nand erase 0x100000 0x2000
NAND erase: device 0 offset 0x100000, size 0x2000
Erasing at 0x100000 -- 200% complete.
OK
  >
-- cut --

Correct this and give user a warning that more is erased than specified:

-- cut --
  > nand erase 0x100000 0x2000
NAND erase: device 0 offset 0x100000, size 0x2000
Warning: Erase size 0x00002000 smaller than one erase block 0x00004000
           Erasing 0x00004000 instead
Erasing at 0x100000 -- 100% complete.
OK
  >
-- cut --

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
2008-05-28 11:06:27 -05:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Wolfgang Denk
d2c6fbec43 onenand: rename 16 bit memory copy into memcpy_16() to avoid conflicts
Onenand needs a version of memcpy() which performs 16 bit accesses
only; make sure the name does not conflict with the standard
function.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-01 21:30:16 +02:00
Matthias Fuchs
c63ad6325a cfi-flash: Add CFG_FLASH_AUTOPROTECT_LIST
This patch adds a configurable flash auto protection list that can be used
to make U-Boot protect flash regions in flash_init().

The idea has been discussed on the u-boot mailing list starting
on Nov 18th, 2007.

Even this patch brings a new feature it is used as a bugfix for 4xx
platforms where flash_init() does not completely protect the
monitor's flash range in all situations.

U-Boot protects the flash range from CFG_MONITOR_BASE to
(CFG_MONITOR_BASE + monitor_flash_len  - 1) by default. This does not
include the reset vector at 0xfffffffc.

Example:
#define CFG_FLASH_AUTOPROTECT_LIST {{0xfff80000, 0x80000}}

This config option will auto protect the last 512k of flash that
contains the bootloader on board like APC405 and PMC405.

Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
2008-04-25 15:52:14 +02:00
Troy Kisky
84c01d3a05 PATCH - Fix oob data copied into supplied buffer
This patch correctly sets the oobavail variable
and fixes a bug where the oob data was not valid when
there where multiple groups in oobfree.

First segment fixes a typo
Second segment fixes a bug where oob data may be copied incorrectly.
Third segment adds an error message when exiting due to write protect.
Forth segment fixes a bug where oobavail may be set incorrectly.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2008-04-21 08:43:46 +02:00
Ulf Samuelsson
c3a60cb3bd Clean up dataflash partitioning
This patch removes the board dependent parts from
"drivers/mtd/dataflash.c".
Each board relying on this, will have the appropriate
code in a new file, "partition.c" in the board directory.
board Makefiles updated to use the file.

The dataflash partitions are aligned on sector/page boundaries.

The CONFIG_NEW_DF_PARTITION was used to create named partitions
This is now the default operation, and the CONFIG variable is removed.

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
2008-04-18 00:24:05 -07:00
Mike Frysinger
e25cb8d3f4 Remove conflicting NAND ID
There are two NAND entries with ID 0xDC and this obviously causes problems.
In the kernel, they punted the first entry, so we should do the same.

See this upstream e-mail for more info:
http://lists.infradead.org/pipermail/linux-mtd/2007-July/018795.html

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-04-17 14:56:56 -07:00
Kyungmin Park
77e475cc0e Fix OneNAND read
It should access with 16-bit instead of 8-bit

Now it uses the generic memcpy with 8-bit access. It means it reads wrong data from OneNAND.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-04-13 23:11:16 -07:00
Guennadi Liakhovetski
96ef831f71 cfi_flash: Support buffered writes on non-standard Spansion NOR flash
Some NOR flash chip from Spansion, for example, the s29ws-n MirrorBit
series require different addresses for buffered write commands. Define a
configuration option to support buffered writes on those chips. A more
elegant solution would be to automatically detect those chips by parsing
their CFI records, but that would require introduction of a fixup table
into the cfi_flash driver.

Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
2008-04-12 08:59:09 +02:00
Wolfgang Denk
a1b215e2a2 Merge branch 'master' of git://www.denx.de/git/u-boot-at91 2008-04-08 00:16:36 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b5873f1732 dataflash: Move CONFIG_HAS_DATAFLASH to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-04-01 07:30:51 +02:00
Stelian Pop
5604e2178c Cleanup DataFlash partition handling
DataFlash partition information has become a mess. This patch
defines a single partition scheme for Atmel DataFlashes. This partition
scheme will be used by all AT91CAP9 and AT91SAM9 boards.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-04-01 01:43:59 +02:00
Daniel Hellstrom
97bf85d784 MTD/CFI: flash_read64 is defined a weak function (for SPARC)
SPARC has implemented __raw_readq, it reads 64-bit from any 32-bit address.
SPARC CPUs implement flash_read64 which calls __raw_readq.

For current SPARC architectures (LEON2 and LEON3) each read from the
FLASH must lead to a cache miss. This is because FLASH can not be set
non-cacheable since program code resides there, and alternatively disabling
cache is poor from performance view, or doing a cache flush between each
read is even poorer.

Forcing a cache miss on a SPARC is done by a special instruction "lda" -
load alternative space, the alternative space number (ASI) is processor
implementation spcific and can be found by including <asm/processor.h>.

Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
2008-03-29 06:51:04 +01:00
Tor Krill
90447ecbba MTD/CFI: Add support for 16bit legacy AMD flash
Add entry for 512Kx16 AMD flash to jedec_table.
Read out 16bit device id if chipwidth is 16bit.
Fixed coding style after Stefans feedback

Signed-off-by: Tor Krill <tor@excito.com>
2008-03-28 11:44:23 +01:00
Kyungmin Park
1bb707c39a Add Flex-OneNAND booting support
Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array
using a NOR Flash interface. This on-chip integration enables system designers
to reduce external system logic and use high-density NAND Flash
in applications that would otherwise have to use more NOR components.

Flex-OneNAND enables users to configure to partition it into SLC and MLC areas
in more flexible way. While MLC area of Flex-OneNAND can be used to store data
that require low reliability and high density, SLC area of Flex-OneNAND
to store data that need high reliability and high performance. Flex-OneNAND
can let users take advantage of storing these two different types of data
into one chip, which is making Flex-OneNAND more cost- and space-effective.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-03-26 00:05:32 +01:00
Stefan Roese
f0105727d1 CFI: Small cleanup for FLASH_SHOW_PROGRESS
With this patch we don't need that many #ifdef's in the code. It moves
the subtraction into the macro and defines a NOP-macro when
CONFIG_FLASH_SHOW_PROGRESS is not defined.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
2008-03-19 13:41:25 +01:00
Jerry Van Baren
9a042e9ca5 Flash programming progress countdown.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2008-03-19 13:41:25 +01:00
Michael Schwingen
1ba639da56 CFI: Do not use uninitialized cmd_reset
Do not use uninitialized cmd_reset; issue both AMD and Intel reset
commands instead

From a short test, it looks like AMD-style flash roms treat *any* unknown
command write as a reset, at least when in CFI Query mode, so issuing the
Intel reset command to AMD-style flashs seems safe (from the small sample I
have), plus the 3-cycle magic sequence should kick the state machine into
the right state even without a reset command. Since the AMD-style flashs
require the unlock sequence for real operation, I chose to try the AMD reset
command first, so that Intel flashs do no see an invalid command prior to
the CFI query.

I have tested the patch on AM29LV320-style flashs from Fujitsu and Macronix,
plus Intel StrataFlash.

Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-02-21 17:12:19 +01:00
Stelian Pop
20b197c6f2 AT91CAP9 support : build integration
Signed-off-by: Stelian Pop <stelian@popies.net>
2008-02-14 09:37:57 +00:00
Stelian Pop
d49fe4bed5 Improve DataFlash CS definition.
Use a structure instead of the error prone unnamed array to
define the possible dataflash banks.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-02-14 09:37:56 +00:00
Kumar Gala
3cfb0c51b2 Remove duplicate defines for ARRAY_SIZE
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-02-14 00:43:02 +01:00
Stelian Pop
c77ce474b1 Fix incorrect address test in AT91F_DataflashSelect().
Signed-off-by: Stelian Pop <stelian@popies.net>
2008-02-14 00:37:23 +01:00
Anton Vorontsov
cd9d23053d nand: FSL UPM NAND driver
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16 14:14:40 +01:00
Kyungmin Park
6cb2239ae7 OneNAND: Separate U-Boot dependent code from OneNAND
OneNAND: Separate U-Boot dependent code from OneNAND

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2008-01-16 14:10:15 +01:00
Michael Schwingen
8225d1e3ac CFI: Fix CONFIG_FLASH_CFI_LEGACY compilation
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Acked-by: Stefan Roese <sr@denx.de>
2008-01-13 15:07:26 +01:00
Marcel Ziswiler
7817cb2083 fix comments with new drivers organization
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:48:49 +01:00
Stefan Roese
ce37422d00 cfi_flash: Fix bug in flash_isset() to use correct 32bit function
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-01-02 16:07:01 +01:00
Stefan Roese
0dc80e2759 cfi_flash: Add missing check for erased dest to flash_write_cfibuffer()
The check for an sufficiently erased destination was missing in the
buffered write function of the cfi flash driver (when
CFG_FLASH_USE_BUFFER_WRITE is defined). This patch adds this check to that
writing to such a region will fail with the currect error message.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-27 07:50:54 +01:00
Haavard Skinnemoen
467bcee11f cfi_flash: Add manufacturer-specific fixups
Run fixups based on the JEDEC manufacturer ID independent of the
command set ID.

This changes current behaviour: Previously, geometry reversal for AMD
chips were done based on the command set ID, while they are now done
based on the JEDEC manufacturer and device ID.

Also add fixup for top-boot Atmel chips. A fixup is needed for
AT49BV6416(T) too, but since u-boot currently only reads the low byte
of the device ID, there's no way to tell it apart from AT49BV642D,
which should not have this fixup. Since AT49BV642D support is
necessary to get ATNGW100 board support into mainline, I've commented
out the fixup for now.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-17 15:48:38 +01:00
Haavard Skinnemoen
0ddf06ddf6 cfi_flash: Add cmdset-specific init functions
Move things like reading JEDEC IDs and fixing up geometry reversal
into separate functions. The geometry reversal fixup is now performed
by altering the qry structure directly, which makes the sector init
code slightly cleaner.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-17 15:48:31 +01:00
Haavard Skinnemoen
e23741f4a6 cfi_flash: Read whole QRY structure in one go
Read out the whole CFI Standard Query structure after successful cfi
identification. This allows subsequent code to access this information
directly without having to go through flash_read_uchar() and friends.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-17 15:48:25 +01:00
Haavard Skinnemoen
12d30aa797 cfi_flash: Use map_physmem() and unmap_physmem()
Use map_physmem() and unmap_physmem() to convert from physical to
virtual addresses. This gives the arch a chance to provide an uncached
mapping for flash accesses.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-13 13:15:22 +01:00
Haavard Skinnemoen
cdbaefb5f5 cfi_flash: Introduce read and write accessors
Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
them to access the flash memory. This makes it clearer when the flash
is actually being accessed; merely dereferencing a volatile pointer
looks just like any other kind of access.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-13 13:15:11 +01:00
Haavard Skinnemoen
be60a9021c cfi_flash: Reorder functions and eliminate extra prototypes
Reorder the functions in cfi_flash.c so that each function only uses
functions that have been defined before it. This allows the static
prototype declarations near the top to be eliminated and might allow
gcc to do a better job inlining functions.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-13 13:14:55 +01:00
Haavard Skinnemoen
3055793bcb cfi_flash: Make some needlessly global functions static
Make functions not declared in any header file static.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-13 13:12:46 +01:00
Haavard Skinnemoen
7e5b9b4715 cfi_flash: Break long lines
This patch tries to keep all lines in the cfi_flash driver below 80
columns. There are a few lines left which don't fit this requirement
because I couldn't find any trivial way to break them (i.e. it would
take some restructuring, which I intend to do in a later patch.)

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-12-13 13:11:45 +01:00
Bartlomiej Sieka
42026c9cb3 CFI: synchronize command offsets with Linux CFI driver
Fixes non-working CFI Flash on the Inka4x0 board.

Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
2007-12-13 12:00:37 +01:00
Stefan Roese
9692c2734a CFI: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-08 08:25:09 +01:00
Michael Schwingen
81b20ccc2d CFI: support JEDEC flash roms in CFI-flash framework
The following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".

Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-12-08 08:16:50 +01:00
Jean-Christophe PLAGNIOL-VILLARD
59829cc189 drivers/mtd : move mtd drivers to drivers/mtd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2007-11-25 23:28:52 +01:00