The config header for this platform disables both CMD_SF and CMD_SPI and
the defconfig leaves them enabled. Disable them from the defconfig and
enable them in the header.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masakazu Mochizuki <masakazu.mochizuki.wd@hitachi.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The common config header for bcm7260 and bcm7445 enable
CONFIG_CMD_EXT2/EXT4 but the defconfigs do not. This results in the
commands being disabled. Enable them via the defconfig.
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The config header for this platform uses '#undef' in a number of cases.
All of the MMC related ones were already handled correctly in the
defconfig file. In the case of CONFIG_CMD_FUSE, the command was being
built and enabled via defconfig. Disable it in the defconfig, cleanup
the header.
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than only enable CONFIG_CMD_NAND for non-SPL builds, move the CMD
options to defconfig and rework the guards to not try and call the
function in SPL builds.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The symbol "CONFIG_ARM_DCC" is used to control building
drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this.
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Enable DM_ETH on all the defconfigs for the T1024RDB board.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable DM_ETH on all the defconfigs for the P2041RDB board.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
With sifive_fu540_defconfig:
User can use FSBL or u-boot-spl.bin anyone at a time.
For FSBL,
fsbl->fw_payload.bin (opensbi + U-Boot)
For u-boot-spl.bin,
u-boot-spl.bin->FIT image (opensbi + U-Boot proper + dtb)
U-Boot SPL will be loaded by ZSBL from SD card (replace fsbl.bin with
u-boot-spl.bin) and runs in L2 LIM in machine mode and then load FIT
image u-boot.itb from SD card into RAM.
U-Boot SPL expects u-boot.itb FIT image at the starting of SD card sector
number (0x822) of GUID type "2E54B353-1271-4842-806F-E436D6AF6985"
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that the EMAC driver supports the H6 SoC, we can enable the Ethernet
hardware on the Pine H64 board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- set ARCH_FIXUP_FDT_MEMORY
- bump NR_DRAM_BANKS to four to enable 8 GB of RAM
-----BEGIN PGP SIGNATURE-----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=uKBu
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.07.2' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
rpi4:
- set ARCH_FIXUP_FDT_MEMORY
- bump NR_DRAM_BANKS to four to enable 8 GB of RAM
- Fix mmc of path after syncfrom kernel dts;
- Add dwc3 host support with DM for rk3399;
- Add usb2phy and typec phy for rockchip platform;
- Migrate board list doc to rockchip.rst;
- Add rk3399 Pinebook Pro board support;
- Update dram_init in board_init and add memory node in SPL;
With the new RPi4 which has 8 GB of RAM, we can have up to four DRAM
banks. Bump up the configuration files to detect all the memory in
U-Boot.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As discussed at https://lore.kernel.org/linux-arm-kernel/b726290c-1038-3771-5187-6ac370bc92c9@arm.com/T/
the defconfig for rpi4 miss CONFIG_ARCH_FIXUP_FDT_MEMORY.
Without it, booting with an initrd fail.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
USB stack uses DM so DM_KEYBOARD is needed to get USB keyboard working.
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable USB3.0 Host support for ROC-RK3399-PC boards.
Tested USB3.0 SSD on Type C1 port on board.
=> usb start
starting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
=> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 100mA)
USB 2.0 Hub [MTT]
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Hub (480 Mb/s, 0mA)
| | VIA Labs, Inc. USB2.0 Hub
| |
| +-4 Hub (480 Mb/s, 100mA)
| | USB 2.0 Hub
| |
| +-5 (480 Mb/s, 100mA)
| VIA Technologies Inc. USB 2.0 BILLBOARD 0000000000000001
|
+-3 Hub (5 Gb/s, 0mA)
| VIA Labs, Inc. USB3.0 Hub
|
+-6 Mass Storage (5 Gb/s, 224mA)
JMicron External Disk 3.0 DB12345678A2
=> usb reset
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3c0000: USB EHCI 1.00
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 2 USB Device(s) found
scanning bus dwc3 for devices... 6 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update evb-rk3399 default config to support USB3.0 Host.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable richer HUSH shell to make working with the board more pleasant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
U-Boot has video output enabled so time to get keyboard working.
=> usb reset;usb tree
resetting USB...
Bus usb@fe380000: USB EHCI 1.00
Bus usb@fe3a0000: USB OHCI 1.0
Bus usb@fe3c0000: USB EHCI 1.00
Bus usb@fe3e0000: USB OHCI 1.0
Bus dwc3: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fe380000 for devices... 1 USB Device(s) found
scanning bus usb@fe3a0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3c0000 for devices... 1 USB Device(s) found
scanning bus usb@fe3e0000 for devices... 3 USB Device(s) found
scanning bus dwc3 for devices... cannot reset port 1!?
2 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
USB device tree:
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
U-Boot Root Hub
1 Hub (480 Mb/s, 0mA)
u-boot EHCI Host Controller
1 Hub (12 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Hub (12 Mb/s, 100mA)
| ALCOR Generic USB Hub
|
+-3 Mass Storage (12 Mb/s, 200mA)
Kingston DT 101 G2 001478544887BB3157380157
1 Hub (5 Gb/s, 0mA)
| U-Boot XHCI Host Controller
|
+-2 Mass Storage (5 Gb/s, 76mA)
ADATA ADATA USB Flash Drive 1520405012240002
Signed-off-by: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable DWC3 core, gadget for nanopc-t4 board.
This would help to use fastboot by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Since the KS8851 driver is now in, enable the Kconfig entry on DHCOM
to make the second ethernet available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Veyrons do not need full pinctrl support for SPL.
The full pinctrl support does nothing when enabled with OF_PLATDATA,
thus was already unused.
This frees about 4kB of SPL size.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Previously veyron_init() was called in board_init() context, which is
called after relocation. Moving it to veyron.c used board_early_init_f
which is called way earlier, and causes veyron_init to hang.
Using board_early_init_r instead fixes this.
Fixes: b678f2790c ("rockchip: rk3288: Move veyron_init() back to veyron.c")
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Due to board limitation some SSD's would work
on rock960 PCIe M.2 only with 1.8V IO domain.
So, this patch enables grf io_sel explicitly to
make PCIe/M.2 to work.
Cc: Tom Cubie <tom@radxa.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reference to commit that adds HDMI to other rk3399 boards:
commit 9778edae55 ("rockchip: Enable HDMI output on rk3399 board w/ HDMI")
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
drivers/net/smc911x.c has been converted to DM.
select DM_ETH to enable it for all the UniPhier platform boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add DM_ETH support for lx2160aqds, ls2080aqds, ls1088aqds
- QSI related fixes on ls1012a, ls2080a, ls1046a, ls1088a, ls1043a based
platforms
- Bug-fixes/updtaes related to ls1046afrwy, fsl-mc, msi-map property
Enable OpTee support on R-Car Gen3, so that U-Boot would copy the
OpTee /firmware and /reserved-memory nodes into the Linux DT.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
the mpc83xxx suvd3 variant is not longer used, so
remove it.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
With the converstion of SMC911x to DM, this can facilitate the omap3
boards from LogicPD (now called Beacon EmbeddedWorks) to be converted.
There isn't a clean solution to doing this in phases, so the boards are
all being done together to avoid breaking functionality.
Because the GPMC bus hasn't been converted, the -u-boot.dtsi node needs
to show the address of the ethernet controller for each board.
The board file, which is common betwen the OMAP35 and DM37 SOM LV and
Torpedo boards, can remove the manual ethernet initialization, but it
still needs to register the address and GPMC configuration for the Ethernet
controller which is now being moved around to board_late_init().
Lastly, this patch updates the various config files to add the reference
for DM_ETH and remove the SMC address, which is now fetched from the
newly created device tree nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LS2080AQDS board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LS1088AQDS board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_ETH and CONFIG_DM_MDIO and related configs for the
LX2160AQDS board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit 323d3af59f ("configs: ls1012ardb: Enable
CONFIG_SYS_RELOC_GD_ENV_ADDR") enables the config only for LS1012ARDB.
Apart from LS1012A-RDB, other platforms such as LS1012A-FRWY, LS2088A
and LS1046A-RDB/FRWY also require this config to be enabled. This also
helps in resolving booting crash observed in flash environment.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and
CONFIG_ENV_SIZE values. If both config values are same, flash
environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be
same as that of flash sector size, this entry cannot be changed.
Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config
value aligned with other boards environemt size.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.kumar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
The macro value is already defined in ls1046ardb_tfa_defconfig, also
define the value as 0x40300000 in qspi_defconfig.
ls1046aqds has one spansion flash "S25FL128S_64K" of size 16M with
sector size 64K. Correct ENV_ADDR and ENV_SECT_SIZE value for QSPI and
TFA defconfigs of the board.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region in LS2088ARDB and LS2088AQDS starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Also, define config value as 0x20300000 in qspi defconfig.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_ENV_ADDR helps in picking environment from flash before DDR init.
QSPI region starts from 0x20000000 offset.
Correct the config value i.e 0x80500000 -> 0x20500000.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_SPI_FLASH_SPANSION in defconfigs of LS1046ARDB and
LS1046AQDS which have two spansion flases i.e s25fs512s each of size
64M.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move CONFIG_FSL_QSPI to the board defconfigs and while at it also move
CONFIG_SPI_FLASH_SPANSION for LS1043AQDS.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Previous patches allow UEFI secure variables to be stored in an RPMB
device using OPTEE. Add a config for the lx2160a hardware so the feature
gets at least compiled.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Remove superfluous differences to lx2160ardb_tfa_defconfig.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable CONFIG_PCI_INIT_R for qemux86 and qemux86-64 pci enumeration during
boot in order to eliminate the custom preboot commands in
include/configs/qemu-x86.h.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
The SPL linker script had been left in arch/$(ARCH)/cpu/$(CPU)/$(SOC);
therefore move it to the already-established arch/$(ARCH)/mach-$(SOC)
location.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
-----BEGIN PGP SIGNATURE-----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=66oV
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.07' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- fix phy configuration for RPi4's bcmgenet
- sync RPi4's env size with other RPi configs
- add kconfig option to reserver more pages in the EFI mem map
- add support for SDMA which is used by RPi4
- fix corner case boot bug for RPi3 32-bit
The SPI NOR nWP line is connected to GPIO PF7 on the SoM,
pull the GPIO line high by default to clear SPI NOR WP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Define I2C EEPROM bus and address, so that the 'eeprom' command uses
the correct ones and does not generate the following error:
eeprom_rw_block: Cannot find udev for a bus 0
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of errno_str, used in command pmic and regulator.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Need Realtek driver to manage in RTL8211F the configuration of the LED.
Initialize LCR (LED Control Register) to configure green LED for Link,
yellow LED for Active
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43
Add default U-Boot configuration for the DHCOR SoM on AV96 board.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Use the same environment size as the configs dedicated for rpi3 and rpi4.
This allows to switch between the builds and not to loose the settings
stored on the SD card.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable the second USB controller, which is connected to a hub with 4
ports. The first controller is for the OTG port and is currently not
supported.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
[narmstrong: removed useless DWC2_UTMI_WIDTH in meson64.h]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After this change both device display and serial console would contain
U-Boto output automatically without any future configuration. This would
allow easier debugging on real device as access to serial console is hard
and also in qemu emulator where it is easier to copy+paste from serial
console as from SDL framebuffer.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
In commit commit 43ede0bca7 ("Kconfig: Migrate MTDIDS_DEFAULT /
MTDPARTS_DEFAULT") were removed definitions for onenand partitions.
Revert them back and enable needed options for onenand support.
Signed-off-by: Pali Rohár <pali@kernel.org>
In commit commit 37304aaf60 ("Convert CONFIG_USE_PREBOOT and
CONFIG_PREBOOT to Kconfig") was moved complicated multiline script code
from C header to oneliner in defconfig. After this change multiline to wide
oneliner it is hard to read this code and even harder to debug. Moreover
this script code should be at place where are other scripts, so move it
back to C header file.
Define new env variable preboot which stores this script and in option
CONFIG_PREBOOT calls this preboot variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
