Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for 837x.
This change guarantees that the environment will be located on the
first flash sector after the U-Boot image.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot itself uses GMII mode on the 8360. Fix up UCC phy-connection-type
properties in the device tree so the PHY gets configured for internal delay on
RX only by the OS, as prescribed by mpc8360 rev. 2.1 pb mds erratum #2.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
The MPC8315E SoC including e300c3 core and new IP blocks,
such as TDM, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
The MPC837x SoC including e300c4 core and new IP blocks,
such as SDHC, PCI Express and SATA controller.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Despite user manual, BCSR9.7 is negated (high) on HRST, so
UART2 is disabled. Fix that and configure QE pins properly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Fix the definitions of CFG_ENV_ADDR and CFG_ENV_SECT_SIZE for all of the
currently-defined 83xx boards. This change guarantees that the environment
will be located on the first flash sector after the U-Boot image.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Now that there are no board-specific versions of
"denali_core_search_data_eye()", the weak binding on the common version
can be removed.
Signed-off-by: Larry Johnson <lrj@acm.org>
On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.
This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
Signed-off-by: Stefan Roese <sr@denx.de>
Note: this patch changes the configuration of some GPIO registers:
Register Old Value New Value
--------------- ---------- ----------
DCR GPIO0_TCR 0x0000000F 0x0000F0CF
DCR GPIO0_TSRH 0x55005000 0x00000000
DCR GPIO1_TCR 0xC2000000 0xE2000000
DCR GPIO1_TSRL 0x0C000000 0x00200000
DCR GPIO1_ISR2L 0x00050000 0x00110000
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch makes two additions to GPIO support:
First, it adds function gpio_read_in_bit() to read the a bit from the
GPIO Input Register (GPIOx_IR) in the same way that function
gpio_read_out_bit() reads a bit from the GPIO Output Register
(GPIOx_OR).
Second, it modifies function gpio_set_chip_configuration() to provide
an additional option for configuring the GPIO from the
"CFG_4xx_GPIO_TABLE".
According to the 440EPx User's Manual, when an alternate output is used,
the three-state control is configured in one of two ways, depending on
the particular output. The first option is to select the corresponding
alternate three-state control in the GPIOx_TRSH/L registers. The second
option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
the GPIOx_TRSH/L registers, and set the corresponding bit in the
GPIOx_TCR register to enable the output. For example, the Manual
specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
the alternate three-state control (first option), and specifies
configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
enabled in the GPIOx_TCR register (second option).
Currently, gpio_set_chip_configuration() configures all alternate signal
outputs to use the first option. This patch allow the second option to
be selected by setting the "out_val" element in the table entry to
"GPIO_OUT_1". The first option is used when the "out_val" element is
set to "GPIO_OUT_0". Because "out_val" is not currently used when an
alternate signal is selected, and because all current GPIO tables set
"out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
not change any existing configurations.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch also modifies the functionality of the code so that the data-eye
search is now done with with the cache disabled.
Signed-off-by: Larry Johnson <lrj@acm.org>
When CONFIG_NET_DO_NOT_TRY_ANOTHER is defined U-Boot's
networking stack does not automatically switch to
another interface. This patch does not touch the default
behavior.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch modifies the return code handling in the eth_init()
function, to be compatible with the handling of the return codes in
the other network stack files. It now returns a 0 on Success and -1 on
error.
Signed-off-by: Upakul Barkakaty <upakul.barkakaty@conexant.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are
warned as below:
U-Boot 1.2.0 (Aug 30 2007 - 08:27:37)
DRAM: 256 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Net: NEC-Candy
Warning: NEC-Candy MAC addresses don't match:
Address in SROM is 00:00:4C:80:92:A2
Address in environment is FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21
This patch changes env_enetaddr type from `char' to `unsigned char'.
Cc: Masaki Ishikawa <ishikawa-masaki@cnt.mxe.nes.nec.co.jp>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The purpose of this routine is receiving a single network frame, outside of
U-Boot's NetLoop(). Exporting it to standalone programs that run on top of
U-Boot will let them utilise networking facilities. For sending a raw frame
the already existing eth_send() can be used.
The direct consumer of this routine is the newly introduced API layer for
external applications (enabled with CONFIG_API).
Signed-off-by: Rafal Jaworowski <raj@semihalf.com>
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Include config.h earlier in the set of #includes
so as to avoid a incidental and duplicate definition
of CFG_CACHELINE_SIZE.
Signed-off-by: Jon Loeliger
Assumes the presence of the aliases node in the DTS to
locate the ethernet, pci and serial nodes for fixups.
Use consistent fdtaddr and fdtfile in environment variables.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
This bug was detected on the LWMON5 target which has 2 Intel 16bit wide
flash chips connected to a 32bit wide port.
Signed-off-by: Stefan Roese <sr@denx.de>
The bash builtin versions of the "test" (resp. "[") command allow
using "==" for string comparisons, but POSIX compatible implemen-
tations (like /usr/bin/test) insist on using "=" only. On such systems
you will see:
$ /usr/bin/test a == a && echo OK
/usr/bin/test: ==: binary operator expected
This patch fixes Makefiles and scripts to use POSIX style.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch brings the PMC440 board configuration file.
Finally it enables the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds the first files for the new esd PMC440 boards.
The next two patches will complete the PMC440 board support.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch fixes esd's LCD dectection code to work correctly with
newer gcc versions.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
