Commit graph

19 commits

Author SHA1 Message Date
Jörg Krause
32f9ef3e2b ARM: mxs: Get boot mode from OCRAM
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.

The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.

The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch

Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.

This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/

Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
2015-04-22 14:24:09 +02:00
Graeme Russ
2d6286ab79 arm: mxs: Add 'Wait for JTAG user' if booted in JTAG mode
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)

Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:50 +01:00
Graeme Russ
950eaf6230 arm: mxs: Add debug outputs and comments to mxs SPL source files
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
 - Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
 - Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:49 +01:00
Wolfgang Denk
0060517ae0 cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.

Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-11-07 16:27:07 -05:00
Stefano Babic
bb2637be09 mxs: fix warning in SPL with console support
Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-04-02 10:42:06 +02:00
Marek Vasut
9926eb31b7 arm: mxs: Add serial console support into SPL
Add support for serial console into the i.MX23/i.MX28 SPL. A full,
uncrippled serial console support comes very helpful when debugging
various spectacular hardware bringup issues early in the process.
Because we do not use SPL framework, but have our own minimalistic
SPL, which is compatible with the i.MX23/i.MX28 BootROM, we do not
use preloader_console_init(), but instead use a similar function to
start the console. Nonetheless, to avoid blowing up the size of the
SPL binary, this support is enabled only if CONFIG_SPL_SERIAL_SUPPORT
is defined, which is disabled by default.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-04-01 10:25:11 +02:00
Marek Vasut
65ed5e8572 arm: mxs: Properly set GD pointer in SPL
Set the GD pointer in the SPL to a defined symbol so various
functions from U-Boot can be used without adverse side effects.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-04-01 10:23:01 +02:00
Marek Vasut
9c2c8a3129 arm: mxs: Adjust the load address of U-Boot and SPL for HAB
When using HAB, there are additional special requirements on the placement of
U-Boot and the U-Boot SPL in memory. To fullfill these, this patch moves the
U-Boot binary a little further from the begining of the DRAM, so the HAB CST
and IVT can be placed in front of the U-Boot binary. This is necessary, since
both the U-Boot and the IVT must be contained in single CST signature. To
make things worse, the IVT must be concatenated with one more entry at it's
end, that is the length of the entire CST signature, IVT and U-Boot binary
in memory. By placing the blocks in this order -- CST, IVT, U-Boot, we can
easily align them all and then produce the length field as needed.

As for the SPL, on i.MX23/i.MX28, the SPL size is limited to 32 KiB, thus
we place the IVT at 0x8000 offset, CST right past IVT and claim the size
is correct. The HAB library accepts this setup.

Finally, to make sure the vectoring in SPL still works even after moving
the SPL from 0x0 to 0x1000, we add a small function which copies the
vectoring code and tables to 0x0. This is fine, since the vectoring code
is position independent.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-03-31 18:28:50 +02:00
Marek Vasut
7b8657e2bd ARM: mxs: Receive r0 and r1 passed from BootROM
Make sure value in register r0 and r1 is preserved and passed to
the board_init_ll() and mxs_common_spl_init() where it can be
processed further. The value in r0 can be configured during the
BootStream generation to arbitary value, r1 contains pointer to
return value from CALL'd function.

This patch also clears the value in r0 before returning to BootROM
to make sure the BootROM is not confused by this value.

Finally, this patch cleans up some comments in the start.S file.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-09-10 19:12:54 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Andreas Bießmann
d2eae43ba8 lib: consolidate hang()
Delete all occurrences of hang() and provide a generic function.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-05-01 16:41:08 -04:00
Otavio Salvador
f942f7d962 mx23: SPL: Add boot mode support
This adds the boot mode support for i.MX23 processors.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2013-01-21 12:05:21 +01:00
Marek Vasut
a918a53c36 mxs: Staticize SPL functions
The MXS SPL didn't mark local functions "static". Fix it. This also makes the
SPL smaller by roughly 300 bytes.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-12-04 09:29:11 +01:00
Marek Vasut
320de1354f serial: mxs: spl: Remove empty serial_* functions from SPL code
Remove the empty bodies from serial_* functions from MXS SPL code.
These empty implementations are now in common/serial.c instead so
declaring them also in the SPL code would cause a colision once
serial multi is enabled unconditionally.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:53:57 -07:00
Marek Vasut
d82f05fcad MX28: Fixup the ad-hoc use of DIGCTL_MICROSECONDS
Use proper struct-based access for this register in the SPL code.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-04 11:57:57 +02:00
Otavio Salvador
fa7a51cb82 mxs: Convert sys_proto.h prefixes to 'mxs'
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:25 +02:00
Otavio Salvador
f348199606 mxs: Remove not required explicit iomux-mx28.h include
The iomux header is included on sys_proto.h so to avoid SoC specific
header inclusion.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Marek Vasut <marex@denx.de>
2012-09-01 14:58:25 +02:00
Otavio Salvador
1e0cf5c34b mxs: Reowork SPL to use 'mxs' prefix for methods
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2012-09-01 14:58:17 +02:00
Otavio Salvador
3a0398d7b9 mxs: reorganize source directory for easy sharing of code in i.MXS SoCs
Most code can be shared between i.MX23 and i.MX28 as both are from
i.MXS family; this source directory structure makes easy to share code
among them.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:17 +02:00
Renamed from arch/arm/cpu/arm926ejs/mx28/spl_boot.c (Browse further)