Apple SoCs have an integrated NVMe controller that isn't connected
over a PCIe bus. In preparation for adding support for this NVMe
controller, split out the PCI support into its own file. This file
is selected through a new CONFIG_NVME_PCI Kconfig option, so do
a wholesale replacement of CONFIG_NVME with CONFIG_NVME_PCI.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_SPI_FLASH
CONFIG_ENV_IS_NOWHERE
CONFIG_ENV_OFFSET
CONFIG_ENV_OVERWRITE
CONFIG_ENV_SECT_SIZE
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit f7e16bb0c5, since
the U-Boot doesn't boot if it is booted directly from SPI-NOR with
CONFIG_POSITION_INDEPENDENT=y. Unless fixing this issue, it is better
to revert this change.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Since we can not set OsIndications from Runtime Services
SetVariables at this moment, it is better to ignore the
OsIndications if there is any capsule file in the
correct place.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since the recent commit;
commit b891ff18f8 ("efi_loader: Force a single FMP instance per hardware store")
forces a single FMP instances for a storage, we can not
enable both RAW and FIT capsule image support at once.
Since RAW capsule image support is simpler than FIT,
enable RAW capsule image instead of FIT by default.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Enable UEFI secure boot on synquacer. Note that unless user
setup their keys, the secure boot will not work.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since the U-Boot for the SynQuacer DeveloperBox is designed for
compatible with EDK2 boot, we don't need to support Ext2/4 fs
support by default. Drop it.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since MTD partitions are based on the devicetree name,
remove unneeded mtdparts settings and update DFU setting.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Make the U-Boot binary for SynQuacer position independent so
that the previous bootloader (SCP firmware or BL2) can load
the U-Boot anywhere.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Enable EFI capsule update support. With the EFI capsule update,
you can update U-Boot, TF-A and OP-TEE. TF-A and OP-TEE are
usually combined as a FIP binary, but if the binary is bigger
than 480KB, you have to modify FIP header, split the OP-TEE
and stores the OP-TEE binary in the different place. This
configuration supports both cases.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Add the DeveloperBox 96boards EE support. This board is also
known as Socionext SynQuacer E-Series. It contians one "SC2A11"
SoC, which has 24-cores of arm Cortex-A53, and 4 DDR3 slots,
3 PCIe slots (1 4x port and 2 1x ports which are expanded via
PCIe bridge chip), 2 USB 3.0 ports and 2 USB 2.0 ports, 2 SATA
ports and 1 GbE, 64MB NOR flash and 8GB eMMC on standard
MicroATX Form Factor.
For more information, see this page;
https://www.96boards.org/product/developerbox/
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
