If the NAND is locked tight, commands such as lock and unlock will not
work, but the NAND chip may not report an error. Check the lock tight
status before attempting such operations so that an error status can be
reported if we know the operation will not succeed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
If CONFIG_NAND_ECC_BCH is set we use 4-bit error corretion code
instead of the 1-bit error correction code on the NAND device
within this driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
It could happen (1 out of 100 times) that NAND did not start up correctly after
warm rebooting, so we end up with various failures or DMA timed out due to a
stalled BCH. When resetting BCH together with GPMI, the issue could not be
observed anymore (after 10000+ reboots). We probably need the consistent state
already before sending commands to NAND. This behaviour was observed in barebox
and kernel, so I assume it affects U-Boot as well. I chose to keep the extra
reset for BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
AM33XX with BCH8 can't work with nand_spl_simple correctly
because custom read_page implementation is required for proper
syndrome generation.
This simple driver mostly duplicates nand_spl_simple but has
nand_read_page changed to suit our needs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds support for BCH8 error correction code to omap_gpmc
driver. We use GPMC to generate codes/syndromes but we need ELM to find
error locations from given syndrome.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
[ilya: merge it with omap_gpmc driver, some fixes and cleanup]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND Flash is erased by blocks, not by pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
This patch cleans up nand_util.c:
- Fix tabs.
- Fix typos.
- Remove space character before opening parenthesis in function calls.
- Fix comments.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).
This is the same as a5ff4f102937a3492bca4a9ff0c341d78813414c in Linux
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[scottwood@freescale.com: fix fsl_ifc_sram_init prototype]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Document parameters used for specifying the NAND image to be loaded.
Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only
nand_spl_simple.c, not the entire nand directory. The word "simple" is
there for a reason. :-)
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: updated for makefile changes earlier in patchset
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
nand_ecc.c:82:5: warning: symbol 'nand_calculate_ecc' was not declared. Should it be static?
nand_ecc.c:155:5: warning: symbol 'nand_correct_data' was not declared. Should it be static?
nand_base.c:2854:1: error: directive in argument list
nand_base.c:2856:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Add the missing bits to the Tegra NAND driver to make ONFI detection work
properly.
Also add it to the Tegra default config, as it seems to be a reasonable thing
to have it available on all boards that use any kind of NAND.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Use the same IP revisions as in Linux in order to make the comparison more
clear.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Merge mxc_setup_config1() into board_nand_init() in order to ease the addition
of i.MX5 support in the following patches.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mxc_nand_read_page_raw_syndrome() should reenable ECC upon exit. This fixes ECC
errors left uncorrected after a call to this function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use _mxc_nand_enable_hwecc() instead of duplicating its code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the NFC IP 1.1, the 32-bit ecc_status_result value comes from 2
consecutive 16-bit registers. This patch reads all the fields of this value,
which makes a difference for 4-kiB NF pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is based on Linux kernel -next:
commit 14f44abf1dafc20ba42ce8616a8fc8fbd1b3712b
Author: Brian Norris <computersforpeace@gmail.com>
Date: Fri Jul 13 09:28:24 2012 -0700
mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND_CMD_ constants for lock/unlock should be in the header
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
This is commit 637957551c0ac80de8dfc7650d320c5a98c2c0c0 from Linux
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[scottwood@freescale.com: picked from Linux into U-Boot]
Reported-by: Rafael Beims <rafael.beims@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
With Simon Glass's include/nand.h alignment changes, some mxs builds
were generating errors. Fix is to ensure asm/cache.h is included before
linux/mtd/nand.h. Moving common.h to top of include list does that.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
A device tree is used to configure the NAND, including memory
timings and block/pages sizes.
If this node is not present or is disabled, then NAND will not
be initialized.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The NAND layer needs to use cache-aligned buffers by default. Towards this
goal. align the default buffers and their members according to the minimum
DMA alignment defined for the architecture.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.
To use PMECC in this driver, the user needs to set the PMECC correction
capability, the sector size and ROM lookup table offsets in board config file.
This driver is ported from Linux kernel atmel_nand PMECC patch. The main difference
is in this version it uses registers structure access hardware instead of using macros.
It is tested in 9x5 serial boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch
1. extract the hwecc initialization code into one function. It is a preparation for adding atmel PMECC support.
2. enable CONFIG_SYS_NAND_SELF_INIT. Which make us can configurate the ecc parameters between nand_scan_ident() and nand_scan_tail().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix empty newline at EOF error and move return value check into ifdef]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Orjan Friberg wrote at [1]:
"For the beagleboard, ecc.size is not explicitly set when doing 'nandecc
sw'. If it's not set for the NAND_ECC_SOFT case in nand_scan_tail, it's
set to 256 bytes.
When doing 'nandecc hw', ecc.size is set to 512 bytes. Hence, when
changing back to 'nandecc sw' ecc.size remains at 512 bytes and suddenly
the format has changed."
No patch has been submitted and the issue was still present. This patch
adds the mentioned solution. Tested on a tam3517 board.
[1] http://lists.denx.de/pipermail/u-boot/2012-February/119002.html
cc: Orjan Friberg <of@flatfrog.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
