The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-boot assumes that all FMAN ports have a PHY. Some SoCs (like T1040)
have fixed links. This means that the ports are connected MAC to MAc
and there is no Ethernet PHY attatched. This patch initializes a
FMAN MAC even if it doesn't have a PHY attached.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As auto-negotiation is not supported for 2.5G SGMII, we need
to add a new type PHY_INTERFACE_MODE_SGMII_2500 to differentiate
SGMII-1G and SGMII-2.5G with different setting for auto-negotiation.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Also some fix for QSGMII.
1. fix QSGMII configure of Serdes2.
2. fix PHY address of QSGMII MAC9 & MAC10 for each FMAN.
3. fix dtb for QSGMII interface.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
TBI PHY address (TBIPA) register is set in general frame manager
phy init funciton dtsec_init_phy() in drivers/net/fm/eth.c, and
it is supposed to set TBIPA on FM1@DTSEC1 in case of FM1@DTSEC1
isn't used directly, which provides MDIO for other ports. So
following code is wrong in case of FM2, which has a different
mac base.
struct dtsec *regs = (struct dtsec *)fm_eth->mac->base;
/* Assign a Physical address to the TBI */
out_be32(®s->tbipa, CONFIG_SYS_TBIPA_VALUE);
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Now that phy_startup() can return an actual error code, check for that error
code and abort network initialization if the PHY fails.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part)
Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac)
Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
Fix this:
eth.c: In function 'fm_eth_initialize':
eth.c:651:12: warning: assignment from incompatible pointer type
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
