Enhance the AM65 CPSW NUSS driver to perform a MDIO reset using a GPIO
line. Logic is also added to perform a pre and post delay around reset
using the optional 'reset-delay-us' and 'reset-post-delay-us' properties.
This is similar to the reset being performed in the Linux kernel. The
reset is done once when the CPSW MDIO bus is being initialized.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
The PSIL endpoint data for J721E currently covers only the MCU domain
CPSW0 instance. Add the data for the MAIN domain CPSW0 as well to allow
the MAIN domain Ethernet ports to be usable on any platform using J721E
SoC.
Additionally, since J721E's PSIL endpoint data is applicable to J7200
SoC as well, the MAIN CPSW0 instance on J7200 will also be usable now.
Signed-off-by: Suman Anna <s-anna@ti.com>
[s-vadapalli@ti.com: Update commit message indicating support for J7200]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
- Assorted PCI-related fixes, add Apple Type-C PHY support, semihosting
updates, fix a FAT corner-case, update the help on the pxe cmd and
clean up the gpio uclass slightly.
The current gpio-uclass design uses name field in struct gpio_dev_priv as
an indicator that GPIO is claimed by consumer. This overloads the function
of name field and does not work well for named pins not configured as GPIO
pins.
Introduce separate bitfield array as the claim indicator.
This unbreaks dual-purpose AF and GPIO operation on STM32MP since commit
2c38f7c318 ("pinctrl: pinctrl_stm32: Populate uc_priv->name[] with pinmux node's name")
where any pin which has already been configured as AF could no longer be
claimed as dual-purpose GPIO. This is important for pins like STM32 MMCI
st,cmd-gpios .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide a unit test for semihosting testing reading and writing a file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
We need a platform on which we can test our semihosting code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Currently the "help" displays pxe command help text like this:
=> help
...
printenv - print environment variables
pxe - commands to get and boot from pxe files
To use IPv6 add -ipv6 parameter
qfw - QEMU firmware interface
...
This does not read clearly. Remove the IPv6 stuff as it is in
the detailed help text so that it fits just a single line.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new DM driver supporting FTPCI100 IP used in SoC designs.
This implementation is not based on the old non-DM ftpci100 code
dropped from U-Boot.
Enable the driver in sandbox_defconfig to test compilability.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
The product of two 32 bit integers is a 32 bit integer. Hence
clustcount * bytesperclust may overflow on > 4 GiB devices.
Change the type of clustcount.
Fixes: cb8af8af5b ("fs: fat: support write with non-zero offset")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This function only ever returns 0, but may not assign the second
parameter. Same thing for device_find_next_child(). Do not assign
ret to stop proliferation of this misuse.
Reported-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is merely a dummy driver that makes sure the DWC3 XHCI driver
finds its reset and PHY controllers. We rely on iBoot to set up
the PHY for us.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
The Apple hardware supports 64-bit prefetchable memory windows so
enable CONFIG_SYS_PCI_64BIT. This fixes BAR assignments for the
Broadcom Ethernet controller used in some of the desktop machines.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
To quote the author:
The commit 4fcba5d556 ("regulator: implement basic reference counter")
have made it more important to keep fixed/gpio regulators enable/disable
state in balance.
This series fixes an inbalance in the mmc_dw driver and changes to use
the more relaxed regulator_set_enable_if_allowed function for a few
other drivers.
The regulator_set_enable_if_allowed function is more relaxed and will
return ENOSYS if the provided regulator is NULL or when DM_REGULATOR
was disabled. Using the following call convention should be safe:
ret = regulator_set_enable_if_allowed(<supply>, <true|false>);
if (ret && ret != -ENOSYS)
return ret;
With the commit 4fcba5d556 ("regulator: implement basic reference
counter"), keeping regulator enablement in balance become more important.
Disable vqmmc-supply before signal voltage is changed to keep regulator
enable counter in balance.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # P895 Tegra 3;
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Reviewed-by: Marek Vasut <marex@denx.de>
With the commit 4fcba5d556 ("regulator: implement basic reference
counter") the return value of regulator_set_enable may be EALREADY or
EBUSY for fixed/gpio regulators.
Change to use the more relaxed regulator_set_enable_if_allowed to
continue if regulator already was enabled or disabled.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org> # rockpro64-rk3399
Support booting ChromiumOS on ARM devices using FIT. Add an entry into the
boot implementation which does not require a command line. This can be
expanded over time as the bootm code is refactored.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootflows (such as EFI and ChromiumOS) delay reading the kernel until
it is needed to boot. This saves time when scanning and avoids needing to
allocate memory for something that may never be used.
To permit reading of these files, add a new 'bootflow read' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide an option to dump this information if available.
Move the funciion prototype to the common x86 header. Allow the command
line to be left out since 'bootflow info' show this itself and it is
not in the correct place in memory until the kernel is actually booted.
Fix a badly aligned heading while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the two new functions to separate reading of the ChromiumOS info from
the partition from actually reading the kernel and booting it.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function.
Create a new function which reads the kernel, assuming that the metadata
has been parsed.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
The code to read the ChromiumOS information from the partition is
currently all in one function. It reads the entire kernel, which is
unnecessary unless it is to be booted.
Create a new function which reads just the minimum required data from the
disk, then obtains what it needs from there.
For now this function is not used. Future work will plumb it in.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some bootmeths need to store their own information related to the
bootflow, in addition to the generic information in struct bootflow.
Add a pointer for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new private structure to hold information gleaned from the disk.
This will allow separation between reading of the bootflow information and
(later) reading the whole kernel.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to avoid using #ifdefs around header files and in the code. It
makes sense to collect the various functions used for loading images into
a single header which can be included by all architectures. The best place
for this is the arch-neutral bootm.h header, so use that.
Move some zimage functions into this bootm.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a common base from which the other parts are offset and make all
of the offsets related to that. This makes the code a little easier to
read.
Use X86_ prefixes for the two values which are x86-specific.
Drop OFFSET_BASE since it is available in a header field.
Drop the unnecessary 'start' variable too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Decode the kernel start and size using the structures provided. This
accesses the same data, just in a cleaner way.
Add some logging for some of the fields in the kernel preamble.
Signed-off-by: Simon Glass <sjg@chromium.org>
ChromiumOS allows a kernel to be on either partition 2 or 4. Add support
for scanning both and using the first one we find with a suitable
signature.
Record the partition which is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a header file with structures for booting ChromiumOS, taken from the
vboot tree. Using these makes it easier to understand the code.
Note that the code style has not been updated for U-Boot, with use of
uint64_t, __attribute__((packed)) and one comment-style nit. This should
make it easier to keep the code in sync. It was taken from commit:
5b8596ce ("2sha256_arm: Fix data abort issue")
Update the CHROMEOS string to use the defined values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move the code which reads a partition into its own function. Add a
constant for the number of bytes to 'probe' at the start of the partition.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Rework the arch linker scripts to be consistent for all, support
Kconfig fragments in the board directory and fix some Kconfig options
that were hex-type by default of 0 not 0x0.
Add support to config fragments (.config) located in the /board
directory. This will allow only base defconfigs to live in /configs and
all fragments to live in their respective device directory in /board/..
Signed-off-by: Jason Kacines <j-kacines@ti.com>
Now all linker symbols are declared as type char[]. Though we can
reference the address via both the array name 'var' and its address
'&var'. It's better to unify them to avoid confusing developers.
This patch converts all '&var' linker symbol refrences to the most
commonly used format 'var'.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
1. Convert all linker symbols to char[] type so that we can get the
corresponding address by calling array name 'var' or its address
'&var'. In this way, we can avoid some potential issues[1].
2. Remove unused symbol '_TEXT_BASE'. It has been abandoned and has
not been referenced by any source code.
3. Move '__data_end' to the arch x86's own sections header as it's
only used by x86 arch.
4. Remove some duplicate declared linker symbols. Now we use the
standard header file to declare them.
[1] This patch fixes the boot failure on MIPS target. Error log:
SPL: Image overlaps SPL
Fixes: 1b8a1be1a1 ("spl: spl_legacy: Fix spl_end address")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It is not a parse error to have a default value of "0" for a "hex" type
entry, instead of "0x0". However, "0" and "0x0" are not treated the
same even by the tools themselves. Correct this by changing the default
value from "0" to "0x0" for all hex type questions that had the
incorrect default. Fix one instance (in two configs) of a default of "0"
being used on a hex question to be "0x0". Remove the cases where a
defconfig had set a value of "0x0" to be used as the default had been
"0".
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If an error message contains a function name, it should match the name of
the function throwing the message.
Fixes: 7739d93d82 ("pci: Match region flags using a mask")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The btrfs_decompress() function mostly (u32)-1 on error but it can
also return -EPERM or other kernel error codes from zstd_decompress().
The "ret" variable is an int, so we could just check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Qu Wenruo <wqu@suse.com>
The x509_cert_parse() and pkcs7_parse_message() functions return error
pointers. They don't return NULL. Update the checks accordingly.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This should be allocating the memory for "item" instead of "menu".
The item struct is 48 bytes instead of 96 (assuming a 64bit system)
so this saves a little memory.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Match the "=0x" instead of just "=0".
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Heinrich.Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
