These board files have inconsistent #include ordering. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This memory is used on Bob. Add settings for this, taken from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The u-boot,spl-boot-device property only allows MMC at present. Add SPI as
well for boards that boot from SPI flash.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This file has changed upstream, with some additions and changes. Move the
U-Boot version towards this.
Some USB changes seem to be incompatible with how the bindings work on
rockchip in U-Boot. Testing is needed to make sure that USB still works
correct, and adjust the code (not device tree) if not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Bring in these files from Linux v4.20.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To match the iomux setting of uart2 at SPL, correct the uart2
default pin configuration, if not changed, the evb-rk3229 can't
output the log message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If we use the new pinctrl driver, the pinctrl setup will be done
by device probe. Remove the pinctrl setup at rk3288-board-spl.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It seems that pinctrl is not requested for rk3188 SPL, remove it so
that can save more space for SPL image size.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When the boot ROM sets up MMC we don't need to do it again. Remove the
MMC setup code entirely, but we also need to enable uart for debug message.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds support for the ASUS C201, a RK3288-based clamshell
device. The device tree comes from linus's linux tree at
3f16503b7d2274ac8cbab11163047ac0b4c66cfe. The SDRAM parameters
are for 4GB Samsung LPDDR3, decoded from coreboot's
src/mainboard/google/veyron/sdram_inf/sdram-lpddr3-samsung-4GB.inc
Signed-off-by: Marty E. Plummer <hanetzer@startmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like on rk3399-puma we want to continue booting the fill U-Boot from
the same device as the SPL stage.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This function causes a 5-second delay and stops the display working on
minnie. This code should be in a driver and should only be enabled by
a device-tree property, so that it does not affect devices which do not
have this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jerry uses a max98090 audio codec and the internal SoC I2S peripheral.
Enable sound support and add the required device-tree pieces.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for setting pinctrl and clock for I2S on rk3288. This allows
the sound driver to operate. These settings were created by rkmux.py
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Although not required, it doesn't hurt to explicitly map the USB ports to
a USB controller. Without this, the port number will be derived from the
binding order of the peripheral devices.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This USB port is mainly used for RNDIS and DFU. To be able to use it with
DM_USB and DM_USB_GADGET, we need to provide a dr_mode value in the DTS.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add u-boot specific am335x-shc-u-boot.dtsi file,
in which we add u-boot specific adaptions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
add DTS from linux tree commit
"47bfa6d9dc8c060bf56554a465c9031e286d2f80"
change for U-Boot:
switch to SPDX-license identifier.
Signed-off-by: Heiko Schocher <hs@denx.de>
If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.
Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
There's no reliable way to reuse the hhi entry from the vpu as is done
in the linux kernel, so we duplicate it here.
We will be able to sync against kernel DTS in the future when the VPU
gets based on the clock framework rather than the HHI reg.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.
Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]
Flag the appropriate nodes with u-boot,dm-pre-reloc
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds video output support for Amlogic GXBB/GXL/GXM chips.
The supported ports are CVBS and HDMI (based on DW_HDMI).
When using HDMI, only DMT modes are supported.
There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB)
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed defines alignment in meson_canvas.c]
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.
Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi
Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.
So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook
Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.
If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.
But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.
So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.
If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1
Without aliases of mmc1 = &mmc2;
-------------------------------
MMC: mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2
With aliases of mmc1 = &mmc2;
----------------------------
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK
Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update generation of spl binaries
- continue to generate all SPL files in spl sub-directory
- copy in root folder the needed file for user (YOCTO, buildroot):
u-boot-spl.stm32
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When framebuffer driver init is failed, we should return the err value not 0.
So the video init can exit immediately.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months. This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch sets up an alias for mmc0 to usdhc3.
Before the DM conversion only usdhc3 was enabled and therefore it appeared
as MMC 0 to u-boot. After enabling MMC DM though usdhc3 defaults to MMC 2,
which left unattended would drive changes to existing warp7 bootscripts and
environment variables that rely on mmc 0.
Setup the alias of mmc0 and usdhc3 so that existing warp7 boot code will
work unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This patch imports the Linux kernel warp7 dts as at upstream kernel commit
cf76c364a1e1.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As pointed out by Lucas WDOD1_WDOG_ANY should be WDOG1_WDOG_ANY. Once
corrected we can import the latest kernel DTS unmodified.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
According to "Table 5-1. Boot Device Select" (page 335,
i.MX 6Dual/6Quad Applications Processor Reference Manual, Rev. 4, 09/2017)
the BOOT_CFG1[3] have following values (regarding EIM booting):
0 - NOR flash and 1 - ONENAND
This commit provides correct identification of the boot medium for IMX6Q
boards booting from NOR memory (MCCMON6 is one of them).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
These nodes are required by CX9020 when build with CONFIG_DM_MMC=y
They are copied from Linux 4.20
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
At default, u-boot reserves the memory from SP - 4KB to DRAM end for
lmb in arch_lmb_reserve. So lmb won't allocate any memory from it.
But we found the 4K gap for SP is not enough now, because some FDT
updating operations are added in our u-boot before jumping to kernel,
which needs larger stack. This causes the lmb allocated memory is overwritten
by stack.
Fix the issue by implementing the board_lmb_reserve to reserve from
SP - 16KB to memory end for lmb.
Signed-off-by: Ye Li <ye.li@nxp.com>
Introduce u-boot dtsi for i.MX8QXP MEK board.
we do not introduce a common dtsi for SoC, because different board
has different requirement on which needs to be enabled in SPL DM.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In preparation of adding CONFIG_DM_MMC support use separate device
trees for raw NAND and eMMC devices.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Like it was done on imx6 in commit 9236269de5 ("imx: mx6: Fix
implementantion reset_misc")
Do not call lcdif_power_down() in the SPL case to fix the following
build error:
LD spl/u-boot-spl
MKIMAGE u-boot.img
arch/arm/mach-imx/built-in.o: In function `reset_misc':
/home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down'
scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The following NXP application notes and manual recommend to ensure the
IVT DCD pointer is Null prior to calling HAB API authenticate_image()
function:
- AN12263: HABv4 RVT Guidelines and Recommendations
- AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using
HABv4
- CST docs: High Assurance Boot Version 4 Application Programming
Interface Reference Manual
Commit ca89df7dd4 ("imx: hab: Convert DCD non-NULL error to warning")
converted DCD non-NULL error to warning due to the lack of documentation
at the time of first patch submission. We have warned U-Boot users since
v2018.03, and it makes sense now to follow the NXP recommendation to
ensure the IVT DCD pointer is Null.
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error
if a DCD pointer is present in an image being authenticated by calling the
HAB RVT API. Older versions of HAB will process and run DCD if it is
present, and this could lead to an incorrect authentication boot flow.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Per Kever Yang, 32768 is a reasonable max size for TPL on RK3288.
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like AM33xx and AM43xx, DRA7xx and AM57xx devices may need to
have an non-standard boot address in memory. This may be due
to the device being a high security variant, which place the
Initial SoftWare (ISW) after certificates and secure software.
Allow these devices to set this from Kconfig.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
As Poplar supports running TF-A with OP-TEE as BL32
payload, add op-tee node in DT, which enables usage of
OP-TEE driver (which provides an interface for requesting services
from OP-TEE).
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have converted mmc to driver model on Poplar. So let's clean up
board level mmc initialization code.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
It adds missing pinctrl headers, updates clock header and sync up Poplar
device tree with kernel 4.20 release.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Add pinctrl node for TLMM and add mux request for uart node.
* Rename uart to the actual board uart port.
* Fix indentendation of sdhc2 node.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The TLMM_GPIO_ENABLE bit is actually use to disable
the GPIO. change it to TLMM_GPIO_DISABLE so it's clearer.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add pinctrl driver for Dragonboard820c, currently with only
one mux func to initialize pins for serial console.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The PLL for the UART was not set, and relied on previous
initializtion made by LK. add the appropriate initialization.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Deploy u-boot-spl.stm32 binary in u-boot root folder like
the rest of the boards.
This makes it more streamlined when building in Yocto, Buildroot etc..
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Most of the memory is being consumed by device binding code,
more space needed for other data structures.
Z-turn board has already hit the limit, others may follow soon.
Measuring only the memory consumed in device_bind_common, I've got
the following results (in decimal):
root_driver: 108
mod_exp_sw: 108
amba: 120
serial@e0000000 aka uart0: 112
serial@e0001000 aka uart1: 88
spi@e000d000 aka qspi: 120
sdhci@e0100000 aka mmc0: 455
sdhci@e0100000.blk: 208
slcr@f8000000: 96
clkc@100: 72
(total) 1487 = 0x5cf of 0x600
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The miamiplus contains a speedgrade-2 device, which may run the CPU at 800MHz.
Change the PLL setting to 800MHz, and adapt the setpoints in the devicetree.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar changes was done for Zynq in past and this patch just follow
this pattern to separate cpu code from SoC code.
Move arch/arm/cpu/armv8/zynqmp/* -> arch/arm/mach-zynqmp/*
And also fix references to these files.
Based on
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patches renames sd nodes in dts to be in line with
kernel. This patch also modifies the references for the same
in code.
It checks mmc first to have no time penalty for new DT node names based
on left-to-right expression evaluation.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is hard dependency for CLK_ZYNQMP to have zynqmp_pmufw_version()
but also FPGA code is calling this function which is possible to use
without actual CLK_ZYNQMP firmware driver to be enabled.
This patch enables the case where only fixed-clock CLK setup is used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a range of stackable network switches. The SoC is Armada-385 and
there are a number of variants with differing network port
configurations. The DP variants are intended for a harsher operating
environment so they use a different i2c mux and fit industrial-temp
parts.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The memory area [0x4000000-0x4200000[ is occupied by the PSCI firmware. Any
attempt to access it from U-Boot leads to an immediate crash.
So let's make the same memory reservation as the vendor device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use get_ram_size to determine if the RAM size on Turris Mox is 512 MiB
or 1 GiB.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
DTC issues a warning because #address-cells and #size-cells properties
are not set in the mdio node.
Also add ethernet1 alias.
Also add RTC node.
Also fix USB3 regulator startup delay time.
Also fix PCI Express SERDES speed to 5 GHz (this is only cosmetic, the
speed value is not used byt the comphy driver for PCI Express, but
should be 5 GHz nonetheless).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if Mox modules are connected in supported mode, then configure
the MDIO addresses of switch modules.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the Armada-38x device tree files with Linux 4.20-rc5. The changes
not taken are new compatible strings for the uart and nand flash
controller. The nand binding is best updated if/when the mtd/nand
infrastructure is updated.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CLK and DM_RESET drivers are now available for all of
the Allwinner platforms, so enable them in arch/arm/Kconfig
Enabling CLK will select DM_RESET by default.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A80 devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commits.
arch/arm/boot/dts/sun9i-a80*:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
include/dt-bindings/*/sun9i-a80-*:
commit 783ab76ae553abc23f80ef7511052d055697531b
Author: Chen-Yu Tsai <wens@csie.org>
Date: Sat Jan 28 20:22:36 2017 +0800
clk: sunxi-ng: Add A80 Display Engine CCU
Note: sun9i-a80-cx-a99.dts is updated only uart0, since the same
dts is not available in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add common reset driver for all Allwinner SoC's.
Since CLK and RESET share common DT compatible, it is CLK driver
job is to bind the reset driver. So add CLK bind call on respective
SoC driver by passing ccu map descriptor so-that reset deassert,
deassert operations held based on ccu reset table defined from
CLK driver.
Select DM_RESET via CLK_SUNXI, this make hidden section of RESET
since CLK and RESET share common DT compatible and code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add initial clock driver for Allwinner A64.
Implement USB clock enable and disable functions for
OHCI, EHCI, OTG and USBPHY gate and clock registers
via ccu clk gate table.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Emlid Neutis N5 is a SoM based on Allwinner H5, has a WiFi & BT
module, DDR3 RAM and eMMC.
- add neutis-devboard target to dtb makefile
- add dtsi file for Neutis N5 needs
- add config file for Neutis N5 Dev board
Signed-off-by: Aleksandr Aleksandrov <aleksandr.aleksandrov@emlid.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: update proper commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
To use TWI0/1/2 the user can select CONFIG_I2C#_ENABLE.
However even the controller is enabled, the mux for the pins
are not set.
This patch follows the existing mux method. Since the pads are
different, separate check is added for each i2c.
Tested with A64-SOM204 board.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Remove aliases property name warning while compilation:
Warning (alias_paths): /aliases: aliases property name must
include only lowercase and '-'
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The ICIDs for the qdma device are not configured through SCFG but
through some registers found in the actual device register block.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on
rev1.1 there is only 1 for INTx, so the current fixup is inverse
of the fact.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fixes for TFABOOT framework
- update eMMC bootsrc to SD_MMC
- Increase buffer size for mcinitcmd from 256 to 512
- Fix mcinitcmd and bootcmd for Secure Boot
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This fixes 'arch_lmb_reserve()' for ARM that tries to detect in which
DRAM bank 'sp' is in.
This code failed if a bank was at the end of physical address range
(i.e. size + length overflowed to 0).
To fix this, calculate 'bank_end' as 'size + length - 1' so that such
banks end at 0xffffffff, not 0.
Fixes: 15751403b6 ("ARM: bootm: don't assume sp is in DRAM bank 0")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
It enables DWC2 OTG gadget driver support for Poplar board. As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SDMMC reset is missing from DT, so the reset manager cannot unreset
the SDMMC. Add the missing DT reset entry.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
According to the data sheet bits 10-8 are PHYDRAM_CK_EN. Fix mask
to allow setting PHYDRAM_CK_EN correctly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The Vybrid reference manual VFXXXRM Rev. 0 10/2016 states in chapter
5.2.6.1 DUMMY PADS (DDR/QuadSPI) that those pads need to be programed
for correct operation of DDR. Assume the default DDR pin configuration
which seems to work well on a Colibri VF50.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
When running usb dwc3 gadget driver, we meet random USB enumeration failure in fastboot.
The root cause is a cache coherence issue. When it happens, the ctrl_req in
gadget driver is allocated at 0xfe932f40, and the usb_composite_dev (cdev)
is allocated at 0xfe932f60. So after we submit the setup request (cache flushed) to USB
controller, any accessing to usb_composite_dev variable will cause the cache line refill, then
when setup transfer is completed, reading the setup data in ctrl_req will gets old value from
cache not from memory.
The ctrl_req is allocated by API dma_alloc_coherent, but u-boot don't have cohernet memory.
so it still needs cache maintain operations before/after HW accessing. Since the cache flush or
invalidate bases on cache line, so when the allocated memory size is not cache line aligned,
potentially it may meet such issue.
This patch modifies the dma_alloc_coherent API to round the size to cache line aligned.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is no code for using partition labels in the Allwinner SPL port.
Even so the name is slightly misleading, CONFIG_SPL_LIBDISK_SUPPORT was
meant to guard partition code for the SPL.
Remove the "imply" line in the Kconfig to make this obvious and avoid
unneeded code inclusions, helping to keep the H6 SPL code small.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building peach-pi smdk5420 and peach-pit with thumb mode for SPL
ends-up in the following error:
Error: Thumb encoding does not support an immediate here -- `msr cpsr_c,#0x13|0xC0'
Use an intermediate register to be able to use thumb for exynos5 SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch sets VDD_LOG to 950 mV on RK3399-Q7.
This is required to address stability issues on Puma
in heavy-load use-cases.
Reported-by: Assaf Agmon <assaf@r-go.io>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch eliminates the non-standard entries "rockchip,pwm_id"
and "rockchip,pwm_voltage". They are neither documented nor
read out by any driver.
Additionally it introduces the entry regulator-init-microvolt
and sets it to 900 mV, which is the default target value
for VDD_LOG.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
All the source code of sdram_rk3036.c are from Rockchip, update the
copyright to owned by Rockchip.
Because rockchip may use this copy of code both for open source
project and internal project, update the license to use both
GPL2.0+ and BSD-3 Clause.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is workaround for issue we can't get correct size for 4GB ram
in 32bit system and available before we really need ram space
out of 4GB, eg.enable ARM LAPE(rk3288 supports 8GB ram).
The size of 4GB is '0x1 00000000', and this value will be truncated
to 0 in 32bit system, and system can not get correct ram size.
Rockchip SoCs reserve a blob of space for peripheral near 4GB,
and we are now setting SDRAM_MAX_SIZE as max available space for
ram in 4GB, so we can use this directly to workaround the issue.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Build flash.bin for i.MX8MQ, it will include signed hdmi firmware,
spl, ddr firmware, fit image(bl31.bin, u-boot-nodtb.bin, dtb).
Burn it to 33KB offset of SD card.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Refactor dram_pll_init to accept args to configure different pll freq.
Introduce dram_enable_bypass and dram_disable_bypass
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Build u-boot-dtb.cfgout before checking files, otherwise
u-boot-dtb.cfgout is generated at late stage and cause final image not
generated.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Current implementation of hab_auth_img command needs ivt_offset to
authenticate the image. But ivt header is placed at the end of image
date after padding.
This leaves the usage of hab_auth_img command to fixed size or static
offset for ivt header. New function "get_image_ivt_offset" is introduced
to find the ivt offset during runtime. The case conditional check in this
function is same as boot_get_kernel in common/bootm.c
With this variable length image e.g. FIT image with any random size can
have IVT at the end and ivt_offset option can be left optional
Can be used as "hab_auth_img $loadaddr $filesize" from u-boot script
Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
This file is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This node is in sync with v4.20-next tree:
e4dda4f5a4df "x86/kaslr, ACPI/NUMA: avoid including asm/kaslr.h on arm64"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Introduce two board level callback functions to FIT image loading process, and
a SPL_FIT_FOUND flag to differentiate FIT image or RAW image.
Implement functions in imx common SPL codes to call HAB funtion
to authenticate the FIT image. Generally, we have to sign multiple regions
in FIT image:
1. Sign FIT FDT data (configuration)
2. Sign FIT external data (Sub-images)
Because the CSF supports to sign multiple memory blocks, so that we can use one
signature to cover all regions in FIT image and only authenticate once.
The authentication should be done after the entire FIT image is loaded into
memory including all sub-images.
We use "-p" option to generate FIT image to reserve a space for FIT IVT
and FIT CSF, also this help to fix the offset of the external data (u-boot-nodtb.bin,
ATF, u-boot DTB).
The signed FIT image layout is as below:
--------------------------------------------------
| | | | | | | |
| FIT | FIT | FIT | | U-BOOT | ATF | U-BOOT |
| FDT | IVT | CSF | | nodtb.bin | | DTB |
| | | | | | | |
--------------------------------------------------
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Using ulong is wrong as its size depends on the Host CPU architecture
(32-bit vs. 64-bit) although the Cortex-M4 is always 32-bit.
Without this patch, the stack and PC are obviously wrong and it
generates an abort when used on 64-bit processors such as the i.MX8MQ.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Otherwise can't boot the M4 core as it is impossible to load its
firmware into the TCM memory.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add Kconfig option WATCHDOG_RESET_DISABLE to disable watchdog reset
in imx_watchdog driver, so that the watchdog will not be fed in
u-boot if CONFIG_WATCHDOG_RESET_DISABLE is enabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Support watchdog driver for fsl-lsch2. It's disabled in default.
If you want to use it, please enable CONFIG_IMX_WATCHDOG.
Define CONFIG_WATCHDOG_TIMEOUT_MSECS to set watchdog timeout.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Currently, the DWC3 USB node is out of sync because the bindings
for the UniPhier DWC3 PHY diverged between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch changes mt7629 to use the compatible platform SMP initialization
method of linux kernel.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
For signing the tiboot3.bin image, an optional KEY file can be passed
using CONFIG_SYS_K3_KEY. Right now, Makefile scripts directly takes
the config value and uses it for signing. This is okay if the build
directory is a sub-directory of source tree, otherwise it fails.
Fix it by using the path relative to the source tree.
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
OMAP3_GPIO_x is needed to enable each GPIO bank on the OMAP3
boards. At one point, the #ifdef's were replaced with
if CONFIG_IS_ENABLED but this won't work for people who need
OMAP3_GPIO_x in SPL since the SPL prefix for this option isn't
used in Kconfig. This patch moves the check to #if defined and
also makes Kconfig select the banks if CMD_GPIO is used which
makes the checks in the code less cumbersome.
Fixes: bd8a9c14c9 ("arm: mach-omap2/omap3/clock.c: Enable
all GPIO with CMD_GPIO")
Reported-by: Liam O'Shaughnessy <liam.o.shaughnessy@gumstix.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate omap3_igep00x0.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch allows smaller binaries.
This is needed for and has been tested on Arndale board, as u-boot.bin is
now bigger than the 512K load limit, with GCC8, without thumb mode.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Marvell DDR3 training code is now part of the U-Boot SPL so the
comment saying it needs porting is no longer correct.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable 'fpga' command in u-boot. User will be able to use the FPGA
command to program the FPGA on Stratix10 SoC.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Add a generic mailbox API for FPGA reconfig status which can be
called by others. This new function accepts 2 different mailbox
commands: CONFIG_STATUS or RECONFIG_STATUS.
Signed-off-by: Ang, Chee Hong <chee.hong.ang@intel.com>
Under U-boot, the WiFi SDIO Module should be disabled and the
eMMC modules should be enabled, so this patch adds an s400-u-boot.dtsi
include file specific for U-Boot that will be included by the build system.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:
- UART
- eMMC
- USB
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This is a sync with kernel mainline dts.
The U-Boot eMMC does not need to care about the power for Rockchip
SoCs, because if the board is using eMMC, the power will default on
(for bootrom), so the 'vmmc', 'vqmmc' is only useful for SD in U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
vcc5v0_host and usbhub_enable share gpio4 RK_PA3,
which is a problem during probing (the second probe
will trigger a -EBUSY, when trying to get the gpio handle).
An analysis of the situation shows, that both regulators
are actually describing the same supply.
This patch removes the (currenlty not successful probing)
regulator vcc5v0_host from the DTS and adds the pinctrl-*
setting to usbhub_enable.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Phiilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various
drivers") essentially drops flag DM_FLAG_PRE_RELOC from serial_pl01x
driver for Poplar platform, because the platform falls into the
following strategy category made by the commit.
Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Before the commit lands, Poplar platform works by statically declaring
pl011 serial device via U_BOOT_DEVICE() with DM_FLAG_PRE_RELOC flag set
in the driver. But since Poplar also supports device configuration from
device tree, the commit practically drops the flag for Poplar, and hence
breaks the platform from booting.
This patch changes platform code and device tree to initiate pl011
serial device from device tree rather than static declaration, so that
above strategy about DM_FLAG_PRE_RELOC applies to Poplar, and therefore
the reported boot failure gets fixed.
Reported-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fixes: 4687919684 ("serial: Remove DM_FLAG_PRE_RELOC flag in various drivers")
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When DM_USB is used, either the USB controllers are bound when the DTB
is parsed (when OF_CONTROL is enabled) or they are bound using the
U_BOOT_DEVICES() macro.
In the later case, the platform data is passed in a struct ti_musb_platdata
because it cannot be read from the DTB.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable DM for USB peripheral in the musb-new driver.
Also make sure that the driver can be used in the SPL.
This implies that:
* the driver must work with and without the OF_CONTROL option. That
in turn, implies that the platform data can be passed in a struct
ti_musb_platdata or be read from the dtb
* usb.o is linked in the SPL if host support is enabled
Another change is that the driver does not fail to bind (and stop the boot
process) if one of the child driver does not bind. Reporting the error is
enough. This kind of error would appear if the port is configured in the
DTS but the driver is not activated in the config.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
USB1 can be used by the romboot on all am4372 platforms to download a
firmware (SPL in our case).
It makes sense to enable USB1 in the SPL to download u-boot.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This file is used to override the values found in am4372.dtsi
Use it to fix the "compatible" options for the controllers used
to support the USB (parent bus and syscons).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update snow's device tree and config to use driver model for sound. Also
update the others as best we can.
Spring does not appear to have audio support in the kernel. The smdk5250
and smdk5420 boards use a wolfson codec which I cannot test with. So the
only boards that is tested and known to work are snow, pit and pi.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow setting the i2s pinmux correctly on exyno5420 so that i2c can be
used on that SoC. Also rename EXYNOS_AUDSS to something consistent with
other naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
For snow the codec is at address 0x11 on the i2c bus, in 7-bit format.
The device tree and code are in 8-bit format (i.e. shifted left one bit).
Fix both. Fix pit in a similar way.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need for an embedded device tree for this board so let the
build process generate a separate u-boot.dtb file instead.
Signed-off-by: Felix Brack <fb@ltec.ch>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDiw9AAoJECaAFcEOcohNEa8H/RBWLbVQjHPXf6EjchXgVcSs
Gc+g2QmKZbN21XebfzBpCuZj62NROTWUcrPtor17yEBiMM1xPfe1vC7qtbkR6USj
VTt1JHeyGx3XafkkUpeps382YPfuaNqtabjwZaXlmeE4/VLbXQPE7x4tC4fdWus4
9K3OGQgRNFirn+RIZ7dQWtCby82PEC3cHkPc/n82cVHofcDsgKYK9mPpfcCn/gWF
A4Fa9cx4pjeaMrBHKjcByCiFmwYBPc97Hqzz64oHOdQP0g3h04ko+2w5DdwdeHVV
jKNcvkHESF4m1RGjrTbLEhy1f5UuOfcA1ise/cDX4pjXlBdwxHmvqT5vsE0MQzI=
=5sHL
-----END PGP SIGNATURE-----
Merge tag 'for-master-20181210' of git://git.denx.de/u-boot-rockchip
Improvements:
- init DRAM for RK322x in SPL
- add FAN53555 PMIC/regulator driver
- update MicroCrystal RV3029 driver to Kconfig and sync from Linux
- add bootcount uclass and first DM-driver for bootcount
Now that we have FAN53555 support, we can enable the regulators in our
DTS. To make these easier to identify on the U-Boot commandline, we
rename them to the names of the voltage rails they control.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DRA7 platforms requires that the dtb used in the SPL really matches the
platform to have the best MMC performances.
To detect the board type/version an I2C EEPROM is read. This requires that
DM is initialized before the detection. As a consequence we must reset the
DM after the board detection is a new dtb would better match the platform.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
