We don't need to print this information since it is shown when the MTRRs
are displayed. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert the CRS305-1G-4S board to CRS3xx-98DX3236 to enable easier
implementation of new CRS3xx series boards, based on Marvell Prestera
98DX3236.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Commit f49ac7e1c4 switched the default PHY speed to 3.125Gbit to resolve
issues with SFP modules. However, U-Boot does not have a "2500base-x"
phy-mode.
Resolve this by using "sgmii-2500" instead.
Signed-off-by: Jakov Petrina <jakov.petrina@sartura.hr>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Stefan Roese <sr@denx.de>
Without CONFIG_SYS_U_BOOT_OFFS set to CONFIG_SYS_SPI_U_BOOT_OFFS, U-Boot
will be located at address 0x16000. But, SPL will try to load the
payload from 0x24000 causing the boot to hang.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Without this U-Boot-specific property, booting on the Synology DS414
(or DS214+) fails in SPL. The spi0 DT node is not scanned, as a result
the SPI flash cannot be found.
Signed-off-by: Ezra Buehler <ezra@easyb.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
SMP support for S-mode U-Boot is enabled only if SBI_V01 is enabled.
There is no point in supporting SMP related (IPI and fences) SBI calls
when SBI_V02 is enabled.
Modify all the SMP related SBI calls to be defined only for SBI_V01.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Enable DM_ETH on omap3_logic board
- Enable Caches in SPL for K3 platforms
- Enable backup boot mode support for J721E
- Update the DDR timings for AM654 EVM
- Add automated tests for RX-51
- A few minor Kconfig migrations / corrections
- DFU doc fixes/improvements
- Bugfix for ARMv8, env userspace building, more NULL checks in generic
PHY code
CONFIG_BZIP2 and CONFIG_GZIP_COMPRESSED are Kconfig options. Select them
by CONFIG_SANDBOX instead of setting them in configs/sandbox.h.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the following warning:
cmd/zip.c: In function ‘do_zip’:
cmd/zip.c:30:6: warning: implicit declaration of function ‘gzip’; did you mean ‘do_zip’? [-Wimplicit-function-declaration]
if (gzip((void *) dst, &dst_len, (void *) src, src_len) != 0)
^~~~
do_zip
Include gzip.h header which declares the gzip() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the CONFIG_GZIP_COMPRESSED from a config.h macro to a Kconfig menu
item. It is not selectable by a user because there is no reason to do
so. Instead it will be automatically selected by the stuff which uses
gzip(), like the zip command.
Remove it from the config_whitelist.txt. Also remove
CONFIG_GZIP_COMPRESS_DEF_SZ as this was never used on any board. The
default seems to be sane, otherwise it should be added as a Kconfig
option.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
unzip calls gzwrite() which is provided in lib/gunzip.c. Make sure it is
automatically pulled in if the user selects CMD_UNZIP.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heinrich Schuchardt <xypron.glkp@gmx.de>
As reported by Nicolas Carrier on the Buildroot mailing list [1],
there is a new build issue while building a program which interacts with
the u-boot environment. This program uses the headers of the ubootenv
library provided by uboot-tools.
This is a recent change from uboot [2] adding "#include <env.h>" to
fw_env.h. Adding env.h require a board configuration to build since
it also include compiler.h (and others uboot internal includes).
env.h include seems not needed since env_set() is not used in fw_env tool.
Nicolas removed env.h from fw_env tool and fixed it's build issue.
This problem is present since uboot v2019.10.
[1] http://lists.busybox.net/pipermail/buildroot/2020-April/280307.html
[2] 9fb625ce05
Reported-by: Nicolas Carrier <nicolas.carrier@orolia.com>
Signed-off-by: Romain Naour <romain.naour@gmail.com>
It is possible that users of generic_phy_*() APIs may pass a valid
struct phy pointer but phy->dev can be NULL, leading to NULL pointer
deference in phy_dev_ops().
So call generic_phy_valid() to verify that phy and phy->dev are both
valid.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
include/dfu.h and doc/api/dfu.rst belong to the device firmware update
sub-system. So let's add them to DFU in MAINTAINERS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Add the device firmware update functions to the generated HTML
documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
In dfu_alt_info for eMMC the eMMC partition number can be specified.
The separator in dfu_alt_info is a semicolon not a comma.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
The documentation should rest with the same maintainer as the code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The enum dcache_optoion contains a shift left 2 bits in the armv8 case
already. The PMD_ATTRINDX(option) macro will perform a left shift of 2
bits. Perform a right shift so that in the end we get the correct
value.
[trini: Reword the commit message]
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Convert CONFIG_KS8851_MLL and CONFIG_KS8851_MLL_BASEADDR to Kconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add support for U-Boot DM and DT probing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Instead of reading out the entire FIFO and possibly overwriting U-Boot
memory, read out one packet per recv call, pass it to U-Boot network
stack, and repeat. It is however necessary to cache RXFC value, because
reading that one out clears it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split network handling functions into non-DM specific parts and
common code in preparation for conversion to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Introduce a private data structure for this driver with embedded
struct eth_device and pass it around. This prepares the driver to
work with both DM and non-DM systems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Fix various checkpatch complaints.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
There is only one chip ID in the table of chip IDs for this chip.
Read out the chip ID instead and mask off the last "revision" bit
to check the chip ID, this works for all chips in the family. Then
drop the chip ID passing around.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The packet status and length information should be extracted from the
FIFO per-packet. Adjust the code such that it reads the packet meta
data and then the packet afterward, if applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Most of the entries in the structure are useless, remove them. Inline
the rest of uses where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Per KS8851-16MLL, the RXQCR is a 16bit register. Use 16bit accessors
to it consistently and drop the ks_wrreg8() function altogether, as
it is not used anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The cached RXQCR value is never updated, remove the cache and just use
the bits in the cache directly in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace combination of malloc()+memset() with calloc() as the behavior
is exactly the same and the amount of code is reduced. Moreover, remove
printf() in the fail path, as it is useless, and return proper -ENOMEM
return code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXse5FQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPBfAJ9KNsTM95wQTc/E2zL5hfd58sS3dwCePgugeAkj
+NCwAgKCABJFdS/yBK0=
=w9C+
-----END PGP SIGNATURE-----
Merge tag 'imx8qxp-fixes' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- Fix i.MX8QXP boot hang when getting CPU temperature
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
-----BEGIN PGP SIGNATURE-----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=o+Cy
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc3 (2)
Problems fixed with these patches are:
* UEFI sub-system not working with virtio block devices
* Missing SATA support in UEFI sub-system
* A superfluous debug statement
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
Use the same approach as ROC-RK3328-CC which enables SPL GPIO,
pinctl and regulator support. This allows the gen3 board to
boot through SPL and does not break gen2 in the process.
Signed-off-by: Kurt Miller <kurt@intricatesoftware.com>
Acked-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Veyrons do not need full pinctrl support for SPL.
The full pinctrl support does nothing when enabled with OF_PLATDATA,
thus was already unused.
This frees about 4kB of SPL size.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
