Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Convert CONFIG_SYS_NAND_USE_FLASH_BBT to Kconfig, update defconfigs,
headers and whitelist.
Please note that this symbol already was used in Kconfig
(imply in CONFIG_NAND_ATMEL) which did not work, since this symbol was
not available in Kconfig. This changes now with this patch and all
boards with CONFIG_NAND_ATMEL will have BBT enabled. Which is what
I also need on my GARDENA AT91SAM based board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
[trini: Rework such that the configs are unchanged to start with]
Signed-off-by: Tom Rini <trini@konsulko.com>
The driver brcmnand come from linux kernel 4.18.
Only SoC bcm6838 and bcm6858 are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The driver adds the support for the STMicroelectronics FMC2 NAND
Controller found on STM32MP SOCs.
This patch adds the polling mode, a basic mode that do not need
any DMA channels.
Only NAND_ECC_HW mode is actually supported.
The driver supports a maximum 8k page size.
The following ECC strength and step size are currently supported:
- nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8)
- nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4)
- nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC
based on Hamming)
This patch has been tested on Micron MT29F8G08ABACAH4.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
This patch adds support for nand multi chip select.
Also adding CONFIG_SYS_NAND_MAX_CHIPS to Kconfig to specify maximum number
of nand chips.
Signed-off-by: Tummala Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Each ECC layout consumes about 2984 bytes in the .data section. Allow
to disable the default ECC layouts if a driver is known to provide its
own ECC layout.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
This commit provides code to add proper entry to Kconfig to enable
support for VF610 device tree aware driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
