Commit graph

52364 commits

Author SHA1 Message Date
Timur Tabi
52dbac69c2 fix print_size printing fractional gigabyte numbers on 32-bit platforms
In print_size(), the math that calculates the fractional remainder of a number
used the same integer size as a physical address.  However, the "10 *" factor
of the algorithm means that a large number (e.g. 1.5GB) can overflow the
integer if we're running on a 32-bit system.  Therefore, we need to
disassociate this function from the size of a physical address.

Signed-off-by: Timur Tabi <timur@freescale.com>
2010-05-05 22:17:07 +02:00
Mike Frysinger
b5cebb4fd6 Blackfin: TWI/I2C: implement multibus support
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-05 10:04:38 +02:00
Stefano Babic
b4377e12e9 Add SPI support to mx51evk board
The patch adds SPI devices to the mx51evk board.
The MC13892 chip (PMIC) is supported.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic
d3588a55d4 MX: Added definition file for MC13892
The MC13892 is a Power Controller used with processors
of the family MX.51. The file adds definitions to be used to setup
the internal registers via SPI.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic
d205ddcfc5 SPI: added support for MX51 to mxc_spi
This patch add SPI support for the MX51 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic
e98ecd7110 MX31: Add support for PMIC to the QONG module
Add support for the PMIC (MC13783) controller
and enables charging of the RTC battery.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic
dfe5e14fa2 MX: RTC13783 uses general function to access PMIC
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05 09:48:41 +02:00
Stefano Babic
28bb6d34d3 MX: Added Freescale Power Management Driver
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Magnus Lilja
ba6adeb48e i.MX31: Activate NAND support for i.MX31 Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05 09:48:41 +02:00
Fabio Estevam
60381d6878 MX51: Fix MX51 CPU detect message
Fix MX51 CPU detect message.

Original string was:
CPU:   Freescale i.MX51 family 3.0V at 800 MHz

which can be misinterpreted as  3.0 Volts instead of the silicon revision.

,change it to:
CPU:   Freescale i.MX51 family rev3.0 at 800 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2010-05-05 09:48:41 +02:00
Stefano Babic
68c07a0c21 MX51evk: Removed warnings
Changes reflect modifications in the fsl_esdhc driver
(the clk_enable field war removed in the configuration structure).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Anatolij Gustschin
87db58dca4 tx25: fix crash while booting Linux
Currently booting Linux on TX25 board doesn't work
since there is no correct mach-id and boot parameters
setup for tx25 board. Fix it now.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Kim Phillips
b88c5988db configs: remove unused CONFIG_COMMAND_HISTORY
$ git grep CONFIG_COMMAND_HISTORY
CHANGELOG:    CONFIG_COMMAND_HISTORY
include/configs/AP1000.h:#define CONFIG_COMMAND_HISTORY 1
include/configs/keymile-common.h:#define CONFIG_COMMAND_HISTORY         1
include/configs/manroland/common.h:#define CONFIG_COMMAND_HISTORY               1
$

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2010-05-04 23:38:50 +02:00
Anatolij Gustschin
7769c5bc06 mvsmr: fix link error
MVSMR board support doesn't link since recent rework
of U-Boot directory structure. Fix it now.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Fixed merge conflict
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-04 23:18:45 +02:00
Wolfgang Denk
679ec15462 Merge branch 'master' of git://git.denx.de/u-boot-net 2010-05-04 22:57:37 +02:00
Wolfgang Denk
900a1fe8c8 Merge branch 'master' of git://git.denx.de/u-boot-arm 2010-05-04 22:49:15 +02:00
Mike Frysinger
4324dc72df Blackfin: bfin_mac: hook up new write_hwaddr function
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou
3ac9d6c650 net: ethoc: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou
6c7c444786 net: altera_tse: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Heiko Schocher
fb57ec97b9 net: fec_mxc: add write_hwaddr support
tested on the magnesium board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar
b5ce63ed12 net:kirkwood_egiga.c: MAC addresses programming using write_hwaddr
Added a new function kwgbe_write_hwaddr for programming egiga
controller's hardware address.
This function will be called for each egiga port being used

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Ben Warren
ecee9324d7 Program net device MAC addresses after initializing
Add a new function to the eth_device struct for programming a network
controller's hardware address.

After all network devices have been initialized and the proper MAC address
for each has been determined, make a device driver call to program the
address into the device.  Only device instances with valid unicast addresses
will be programmed.

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Tested-by: Prafulla Wadaskar <prafulla@marvell.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
2010-05-03 14:52:49 -07:00
Thomas Chou
c960b13ed2 net: add altera triple speeds ethernet mac driver
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Thomas Chou
f6569884b4 net: add opencore 10/100 ethernet mac driver
This patch ports the opencore 10/100 ethernet mac driver ethoc.c
from linux kernel to u-boot.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Valentin Yakovenkov
bd75db3feb smc911x driver frame alignment patch
SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.

Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.

But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.

It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.

Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.

It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).

Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar
f0588fdf92 net: Kirkwood_egiga.c bugfixes for rx path
Cosmetic changes: Few comments updated
Functionality: Rx packet frame size is programming should
be done when port is in disabled state. this is corrected

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Eric Jarrige
2e236bf28e fec_mxc.c: Fix MX27 FEC MAC validity check
Fix MX27 FEC logic to check validity of the MAC address in fuse.
Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change.

Signed-off-by:  Eric Jarrige <jorasse@armadeus.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Andy Fleming
538be58568 tsec: Wait for both RX and TX to stop
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped.  We need to wait for both, or the
controller could get into an invalid state.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Mike Frysinger
a45dde2293 net: dm9000x: use standard I/O accessors
The current dm9000x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors.  This can cause problems on
Blackfin systems as the accesses can get out of order.  So convert the
direct volatile dereferences to use the normal in/out macros.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel
5525856d59 mpc512x_fec: Move PHY initialization from probe into init routine.
This saves the autonegotation delay when not using ethernet in U-Boot

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
John Rigby
910119b3c4 fec_mxc don't use internal eeprom on MX25
Avoid using the internal eeprom on MX25 like MX51 already does.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Wolfgang Wegner
33f684d6d5 fix lockup in mcfmii/mii_discover_phy() in case communication fails
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Richard Retanubun
23c34af48f 83xx: UEC: Added support for bitBang MII driver access to PHYs
This patch enabled support for having PHYs on bitBang MII and uec MII
operating at the same time. Modeled after the MPC8360ADS implementation.

Added the ability to specify which ethernet interfaces have bitbang SMI
on the board header file.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Robin Getz
9739946cc5 ./net/net.c - make Microsoft dns servers happy with random_port() numbers
For some reason, (which I can't find any documentation on), if U-Boot
gives a port number higher than 17500 to a Microsoft DNS server, the
server will reply to port 17500, and U-Boot will ignore things (since
that isn't the port it asked the DNS server to reply to).

This fixes that by ensuring the random port number is less than 17500.

Signed-off-by:  Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel
6f5f89f011 Remove unused "local_crc32" function.
For code archeologists, this is a nice example of copy and paste history.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel
aba4b69d01 net: Trivial coding style issue with empty for statement
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:47 -07:00
Prafulla Wadaskar
e3f2a93362 net: Kirkwood_egiga.c: fixed build warnings
This patch fixes following build warnings for kirkwood_egiga.c

kirkwood_egiga.c: In function "kwgbe_init":
kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules
kirkwood_egiga.c: In function "kwgbe_recv":
kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:47 -07:00
Wolfgang Denk
4185ae7a71 Merge branch 'master' of ssh://gemini/home/wd/git/u-boot/master 2010-05-01 00:44:42 +02:00
Wolfgang Denk
0903b524ab Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx 2010-05-01 00:42:22 +02:00
Asen Dimov
20d98c2cea pm9263 converted to at91 soc access
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30 05:23:26 -05:00
Asen Dimov
d6b91e30d3 at91: define matrix registers bit fields
Signed-off-by: Asen Dimov <dimov@ronetix.at>
2010-04-30 05:23:26 -05:00
Stefano Babic
eeb50ce193 MX31: Removed erroneous board name from QONG
QONG is a module that can be installed on several boards,
not only on the QONG-EVB manufactured by Dave srl.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:26 -05:00
Stefano Babic
c9d944d35e MX31: Add UBI support to QONG module
The UBI/UBIFS support is added to the QONG module.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:26 -05:00
Stefano Babic
eab40f819d MX31: Support 128MB RAM on QONG module
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:26 -05:00
Stefano Babic
45997e0a86 MX31: Add support for NAND to QONG board
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Stefano Babic
efb9591069 MX31: add pin definitions for NAND controller
Add pin definitions ralted to the NAND controller to be used
to set up the pin multiplexer.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Stefano Babic
7d27cd08b4 MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Stefano Babic
dfe83352cb mx51evk: correct list of possible BOOT_FROM values
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Stefano Babic
f581e3a215 mkimage: correct spelling error in imximage
Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
John Rigby
34196b0a8b MX25 print arm clock instead of mpllclk on boot
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.

Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:24 -05:00