This patch enables NAND support on the Marvell Armada XP
DB-MV784MP-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update the NAND code to match Linux v4.1. The previous sync was
from Linux v3.15 in commit 4e67c57125.
CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout. Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[scottwood: Cherry-picked from Linux 8471bb73ba10ed67]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add optional LCD support. Note that depending on the toolchain used
one might have to drop some other features to stay within the 0x40000
size limit.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Looks like the define CONFIG_SYS_LCD_PXA_NO_L_BIAS is not used anywhere
else throughout the U-Boot sources any more. Drop it.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Conflicts:
configs/socfpga_arria5_defconfig
configs/socfpga_cyclone5_defconfig
configs/socfpga_socrates_defconfig
Merged these by hand and re-ran savedefconfig on them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable the DWAPB GPIO driver for SoCFPGA Cyclone V and Arria V.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also move the spi flash configurations to the at91-sama5_common.h.
Current at91 zImage size is about 3.3M, the old mapping is not
suitable. So update the spi flash map as following:
0x0 ~ 0x004000: at91bootstrap(16k)
0x04000 ~ 0x008000: u-boot env(16k)
0x08000 ~ 0x060000: u-boot(352k)
0x60000 ~ 0x06c000: dtb (48k)
0x6c000 ~ 0x400000: kernel (3M+592k)
In AT91Bootstrap, the U-Boot in spi flash also update to 0x8000, refer
to following commit in AT91Bootstrap:
3e91e54 Kconfig: fix spi flash address
So also update SPL's u-boot load address to 0x8000 in spi flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
As almost all sama5 sd/mmc env configurations are same, so move them to
at91-sama5_common.h.
Also define CONFIG_ENV_VARS_UBOOT_CONFIG to have the varaible: $board_name.
Then we can use 'at91-${board_name}.dtb' as the dtb name.
TODO: since sama5d3xek has different dtb name, we need to some extra
stuff to make it work on sama5d3xek boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no case where defined(SPL_DISABLE_OF_CONTROL) is true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We do not want to compile the DM remove code for SPL. Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles). This is really ugly.
This commit demonstrates how we can deprecate those two files.
Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The previous commit introduced a useful macro used in makefiles,
in order to reference to different variables (CONFIG_... or
CONFIG_SPL_...) depending on the build context.
Per-image config option control is a PITA in C sources, too.
Here are some macros useful in C/CPP expressions.
CONFIG_IS_ENABLED(FOO) can be used as a shorthand for
(!defined(CONFIG_SPL_BUILD) && defined(CONFIG_FOO)) || \
(defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_FOO))
For example, it is useful to describe C code as follows,
#if CONFIG_IS_ENABLED(OF_CONTROL)
(device tree code)
#else
(board file code)
#endif
The ifdef conditional above is switched by CONFIG_OF_CONTROL during
the U-Boot proper building (CONFIG_SPL_BUILD is not defined), and by
CONFIG_SPL_OF_CONTROL during SPL building (CONFIG_SPL_BUILD is
defined).
The macro can be used in C context as well, so you can also write the
equivalent code as follows:
if (CONFIG_IS_ENABLED(OF_CONTROL)) {
(device tree code)
} else {
(board file code)
}
Another useful macro is CONFIG_VALUE().
CONFIG_VALUE(FOO) is expanded into CONFIG_FOO if CONFIG_SPL_BUILD is
undefined, and into CONFIG_SPL_FOO if CONFIG_SPL_BUILD is defined.
You can write as follows:
text_base = CONFIG_VALUE(TEXT_BASE);
instead of:
#ifdef CONFIG_SPL_BUILD
text_base = CONFIG_SPL_TEXT_BASE;
#else
text_base = CONFIG_TEXT_BASE;
#endif
This commit also adds slight hacking on fixdep so that it can
output a correct list of fixed dependencies.
If the fixdep finds CONFIG_IS_ENABLED(FOO) in a source file,
we want
$(wildcard include/config/foo.h)
in the U-boot proper building context, while we want
$(wildcard include/config/spl/foo.h)
in the SPL build context.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
This causes widespread breakage due to the operation of the low-level code
in crt0.S and cro0_64.S for ARM at least.
The fix is not complicated but it seems safer to revert this for now.
This reverts commit 2afddae075.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When doing a memory mapped copy we may have DMA available and thus need
to have this copy abstracted so that the driver can do it, rather than a
simple memcpy.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch enabled the MVEBU PCIe support on the db-88f6820-gp A38x
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch enabled the MVEBU PCIe support on the db-mv784mp-gp AXP
eval board. It also enabled the Intel E1000 driver support and
adds the initialization of PCIe network controllers to the
board code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
the ECC SDRAM scrubbing that needs to be done in the main U-Boot.
The SPL (previously bin_hdr) has already scrubbed the area:
0x0000.0000 - 0x0100.0000
In this area this main U-Boot needs to get loaded. The main U-Boot
then can scrub the remaining SDRAM area while running from this
location.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for multiple hostcontrollers to the ehci-marvell driver
and enables all 3 usb-hcs on the db-mv784mp-gp board.
It depends on the initial Armada XP usb support patch from Stefan.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enabled the USB/EHCI support for the Marvell
DB-MV784MP-GP Armada XP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The default boot command searches for dofastboot varaiable
and does a fastboot if it is set to 1.
But the condition "if test ${dofastboot} -eq 1" always
returns true if dofastboot is not defined and breaking mmc boot.
So make dofastboot as 0 by default and let the runtime
environment set it if fastboot is required.
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set up interrupts correctly so that Linux can use all devices. Use
savedefconfig to regenerate the defconfig file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we have a simple assignment to gd. With some archs this is
implemented as a register or through some other means; a simple assignment
does not suit in all cases.
Change this to a function and add documentation to describe how this all
works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some archs like to have larger alignment for their global data. Use 16 bytes
which suits all current archs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This part of mentioned commit, was missed by my mistake during the rebase.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Original commit message:
power: pmic: pfuze100 support driver model
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Change-Id: I4fc88414f3c0285f9648e47ec7aed60addeccc4d
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions allow iteration through all PCI devices including bridges.
The children of each PCI bus are returned in turn. This can be useful for
configuring, checking or enumerating all the devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present there are no PCI functions which allow access to PCI
configuration using a struct udevice. This is a sad situation for driver
model as it makes use of PCI harder. Add these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow for configuration of FSP UPD from the device tree which will
override any settings which the FSP was built with itself.
Modify the MinnowMax and BayleyBay boards to transfer sensible UPD
settings from the Intel FSPv4 Gold release to the respective dts files,
with the condition that the memory-down parameters for MinnowMax are
also used.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Removed fsp,mrc-debug-msg and fsp,enable-xhci for minnowmax, bayleybay
Fixed lines >80col
Signed-off-by: Simon Glass <sjg@chromium.org>
The BayTrail SoC has 4 different PCI devices IDs regarding to IDE
and AHCI. Add these IDs in pci_ids.h and also add the other SATA
ID in the Bayley Bay and MinnowMax board configuration header.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
bd->bi_dram[] has both start address and size defined as 32-bit,
which is not the case on some platforms where >=4GiB memory bank
is used. Change them to support such memory banks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add support for 4 1.62G lane eDP panels connected via an anx9804 bridge,
such as found on the Colombus devkit.
While at it also fix the wrong indentation of the SSD2828 Kconfig help text
in board/sunxi/Kconfig.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for making the visual area of the framebuffer smaller and
drawing a black border around it. This is intended for use with
overscanning monitors (esp. with composite video out), to avoid part
of the picture being invisible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
Represent all available RAM in either one or two banks. The first bank
describes any RAM below 4GB. The second bank describes any RAM above 4GB.
This split is driven by the following requirements:
- The NVIDIA L4T kernel requires separate entries in the DT /memory/reg
property for memory below and above the 4GB boundary. The layout of that
DT property is directly driven by the entries in the U-Boot bank array.
- On systems with RAM beyond a physical address of 4GB, the potential
existence of a carve-out at the end of RAM below 4GB can only be
represented using multiple banks, since usable RAM is not contiguous.
While making this change, add a lot more comments re: how and why RAM is
represented in banks, and implement a few more "semantic" functions that
define (and perhaps later detect at run-time) the size of any carve-out.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The new value is the most likely value where the kernel wants to end up
at run-time. Selecting this value as the load address likely avoids the
need to copy the kernel image from the actual load address to the desired
load address. Note that this isn't guaranteed since the kernel may wish
to run at an arbitrary location. In that case, U-Boot will still relocate
the image according to its wishes; this change is a performance
optimization, not a hard-coding of the final image location.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Various clean-ups either in comments, order or spacing without any
functional impact:
- Add some comments in the device trees resp. reorder some parameters
for consistency across all our modules.
- Sort some include files alphabetically (while leaving common.h on
top of course).
- Streamline some comments in the configuration files and fix the
spacing from using spaces to tabs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable CONFIG_IP_DEFRAG and set CONFIG_TFTP_BLOCKSIZE to 16384.
This increases the tftp download speed considerably.
While at it enable CONFIG_TFTP_TSIZE which limits the progress bar to
fifty '#' independent of the downloaded file size.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now as all is in place actually enable UBI/UBIFS support to be able to
boot the Linux kernel and root file system from NAND.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add I2C support in order to subsequently allow disabling the PMIC sleep
mode on low supply voltage.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add LCD display support defaulting to VESA VGA resolution. Different
resolutions configurable via device tree.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Allow detecting whether or not U-Boot was launched through the
recovery mode of the resp. NVIDIA SoC.
Make use of a board specific arch_misc_init() and enable the same via
CONFIG_ARCH_MISC_INIT configuration option.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Allow for optional custom USB gadget manufacturer/product/vendor
IDs/strings to be specified.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Remove spurious new line in configuration file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
9MB reserved for initrd is not enough for default ramfs used for keystone
devices, which is ~33MB. This patch increases the size up to 80MB.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
This patch set the correct initrd address to much rdaddr, which used at
get_fs_ramfs commad.
Fixes: 3e97f0b63c8e ("configs: ti_armv7_keystone2: switch addresses
to generic addresses")
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Add option to set shell prompt string from menuconfig and migrate
boards globally.
The migration is done as follows:
- Boards that explicitly and unconditionally set CONFIG_SYS_PROMPT had the
entry moved to their defconfig files.
- Boards that defined some kind of #ifdef logic which selects the
CONFIG_SYS_PROMPT (for example qemu-mips) got an #undef CONFIG_SYS_PROMPT
right before the #ifdef logic and were left alone.
- This change forces CONFIG_SYS_PROMPT to be a per board decision, and thus
CONFIG_SYS_PROMPT was removed from all <soc>_common.h and <arch>_common.h
files. This results in a streamlined default value across platforms, and
includes the following files: spear-common, sunxi-common, mv-common,
ti_armv7_common, tegra-common, at91-sama5_common, and zynq-common.
- Boards that relied on <arch/soc>_common.h values of CONFIG_SYS_PROMPT were
not updated in their respective defconfig files under the assumption that
since they did not explicitly define a value, they're fine with whatever
the default is.
- On the other hand, boards that relied on a value defined in some
<boards>_common.h file such as woodburn_common, rpi-common,
bur_am335x_common, ls2085a_common, siemens_am33x_common, and
omap3_evm_common, had their values moved to the respective defconfig files.
- The define V_PROMPT was removed, since it is not used anywhere except for
assigning a value for CONFIG_SYS_PROMPT.
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[trini: Add spring, sniper, smartweb to conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Import various DT files for DRA7 / DR72x / dra72-evm from Linux Kernel
v4.1
- Add config file for this board, enable DM and DM_GPIO
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add initial support for CM-T43, an AM437x based SoM.
This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM
detection.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
HiKey is the first 96boards consumer edition compliant board. It features a hi6220
SoC which has eight ARM A53 cpu's.
This initial port adds support for: -
1) Serial
2) eMMC / SD card
3) USB
4) GPIO
It has been tested with Arm Trusted Firmware running u-boot as the BL33 executable.
Notes:
eMMC has been tested with basic reading of eMMC partition into DDR. I have not
tested writing / erasing. Due to lack of clock control it won't be
running in the most performant high speed mode.
SD card slot has been tested for reading and booting kernels into DDR.
It is also currently configured to save the u-boot environment to the
SD card.
USB has been tested with ASIX networking adapter to tftpboot kernels
into DDR. On v2015.07-rc2 dhcp now works, and also USB mass storage
are correctly enumerated.
GPIO has been tested using gpio toggle GPIO4_1-3 to flash the LEDs.
Basic SoC datasheet can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
Hi6220V100_Multi-Mode_Application_Processor_Function_Description.pdf
Board schematic can be found here: -
https://github.com/96boards/documentation/blob/master/hikey/
96Boards-Hikey-Rev-A1.pdf
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
This adds a simple pmic driver for the hi6553 pmic which is used in
conjunction with the hi6220 SoC on the hikey board. Eventually this
driver will be updated to be a proper UCLASS PMIC driver which
can parse the voltages direct from device tree.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Add print_cpuinfo() function and enable
CONFIG_DISPLAY_CPUINFO for keystone platforms,
so that cpu info can be displayed during boot.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This switches the Integrator boards over to using the device model
for its serial ports.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
The new bitfield value must not be higher than its mask.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Now that mailbox driver supports cache flush and invalidation, we can
enable dcache.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
The cacheline is always 32 bytes for arm1176 CPUs, so define it at board
config level for cache handling code.
The ARM Cortex-A7 has a dcache line size of 64 bytes.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This adds support for the fastboot USB gadget, including flashing to the
internal MMC and reboot to bootloader or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update to use Kconfig for MUSB]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that the serial number is correctly defined, we can pass it to the kernel
using the (legacy) ATAG method. It will be automatically passed via device-tree
when enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the omap3 reboot mode mechanism and exports the reboot
mode via an environment variable, that is used in the boot command to make it
possible to boot from the recovery partition.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The LG Optimus Black (P970) codename sniper is a smartphone that was designed
and manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up. This port is aimed at running an Android version
such as Replicant, the fully free Android distribution. However, support for
upstream Linux with device-tree and common GNU/Linux distros boot commands
could be added in the future.
For more information about the journey to freeing this device, please read the
series of blog posts at:
http://code.paulk.fr/article20/a-hacker-s-journey-freeing-a-phone-from-the-ground-up-first-part
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add CONFIG_OF_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows scanning the twl4030 keypad, storing the result in a 64-byte long
matrix with the twl4030_keypad_scan function.
Detecting a key at a given column and row is made easier with the
twl4030_keypad_key function.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for detecting a few inputs exported by the TWL4030.
Currently-supported inputs are the power button, USB and charger presence.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change adds SPL build support to Timll DevKit3250 board, the
generated SPL image can be uploaded over UART5, JTAG or stored on
NAND. SPL is designed to load U-boot image from NAND.
All new NAND chip defines in board configuration are needed by
SPL NAND "simple" framework, the framework is used to reduce
potentially duplicated code from LPC32xx SLC NAND driver.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This change adds more peripherals to Timll DevKit3250 board, namely
MAC and SMSC phy, SLC NAND, GPIO, SPI and I2C.
Also the default serial console is changed to UART5, added an option
to pass device tree blob by means of bootm, predefined environment
variables are slightly extended and reserved space on NAND to store
user defined U-boot environment.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
On the highbank platform the SoC's management controller firmware
will probe the DRAM modules and populates the initial device tree with
the correct values. Therefore the memory sizes in the DT are already
correct, so remove U-Boot's DRAM bank setup so the memory node is not
"fixed up" by u-boot.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <osp@andrep.de>
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
We do not need that "regulator-name" property must be provided in dts.
If "regulator-name" property is not provided in dts, node name
will chosen for settings '.name' field of uc_pdata.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
According to datasheet, SWBST_MODE starts from bit 2 and it occupies 2 bits.
So SWBST_MODE_MASK should be 0xC, and SWBST_MODE_xx should be ([mode] << 2).
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Do not add a bogus (pointing to a non existing serial port) stdout-path
alias to dts on boards without a serial port.
Note that we still define CONS_INDEX as this is used by the SPL where we do
not use DM_SERIAL and thus CONFIG_REQUIRE_SERIAL_CONSOLE is not honored.
We are getting away with this because the sun5i die actually has
an uart0, which in the A13 package is not routed to the outside,
so we are simply sending SPL bootup messages to the tx pin at the
edge of the die, and they go no further from there...
And sofar we only have one A13 board which does not have a serial
port, all others do have a serial port. This kinda makes sense since
the A13 is a much lower pincount package compared to all the other
sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enable the mtdparts command and related options to make support
for SPI NOR MTD useful in any way. With the mtdparts command in
place, it is possible to use partition of the SPI NOR in U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Setting LOADADDR to 0x8000 is a bad idea, it is very likely that
some kind of overlap will happen. Move the LOADADDR 0x01000000
(16MiB from start of RAM) to make sure no overlap happens when
loading kernel for example.
Signed-off-by: Marek Vasut <marex@denx.de>
This is needed to access broken (read: Micron) SPI flashes which
are larger than 16 MiB and don't correctly support 4-byte addressing.
Signed-off-by: Marek Vasut <marex@denx.de>
We do not need full MTD support in the SPL build, it only adds size
and is not usable in any way. Exclude it.
Signed-off-by: Marek Vasut <marex@denx.de>
There is no need to disable support for partitions in the SPL,
we can support partitions in SPL perfectly well. This is likely
some remnant from old times, so just remove this configuration
option.
Moreover, the CRC32 chunk size doesn't have to be adjusted anymore,
since both the GD and malloc area are in RAM by the time this CRC
check can be used and there's plenty of space. Zap this abomination
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Now that the SPL structure is organised such that it matches the
U-Boot's SPL design, it is possible to use the option of relocating
GD to RAM. And since we have GD in RAM, move malloc area to RAM as
well. We point the malloc base pointer 1 MiB past U-Boot's load
address. We use simple malloc for SPL because it is 3kiB smaller
in terms of code size than regular malloc which was used thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Reset the GMAC ethernets based on the "resets" OF node instead of ad-hoc
hardcoded values in the U-Boot code. Since we don't have a proper reset
framework in place yet, we have to do this slightly ad-hoc parsing of the
OF tree instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The GMAC can now be probed from OF, so enable DM ethernet and remove the
old ad-hoc designware_initialize() invocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
setenv an environment variable called "bootmode" , which contains the
board boot mode. This can be in turn used in scripts to determine from
where to load kernel and such.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from QSPI NOR.
Enable support for booting from QSPI NOR.
Signed-off-by: Marek Vasut <marex@denx.de>
Add code and configuration options to support booting from RAW
SD/MMC card as well as for ext4/vfat filesystems. Enable support
for booting from SD/MMC card, but don't enable the filesystem
support just yet to retain compatibility with old SoCFPGA card
format.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove the custom SPL linker script, use the generic one instead.
The custom script doesn't bring in anything new and is only burden
to maintain.
Signed-off-by: Marek Vasut <marex@denx.de>
The code in spl_board_init() should have been in board_init_f()
from the beginning, since it is code which configures system and
then starts DRAM. Thus, it cannot be in spl_board_init(), which
is called from board_init_r() , which already expects a working
DRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement new accessor, sysmgr_get_pinmux_table(), used to obtain pinmux
table and it's size from the QTS-generated pinmux_config.c. The target
here is again to get rid of poluting global namespace by including the
pinmux_config.h into it.
Furthermore, the pinmux_config.h declares some CONFIG_HPS_* macros,
which are explicitly useless to us in U-Boot. Instead, U-Boot does
use DT to detect exactly these configuration options. This patch
makes sure that while this QTS-generated file can stay in the tree,
these obscure macros do not ooze into the namespace anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce accessor iocsr_get_config_table() for retrieving IOCSR config
tables. This patch is again trimming down the namespace polution.
The IOCSR config tables are used only by scan manager, they are generated
by qts and are board specific. Before this patch, the approach to use
these tables in scan manager was to define an extern variable to silence
the compiler and compile board-specific iocsr_config.c into U-Boot which
defined those extern variables. Furthermore, since these are tables and
the scan manager needs to know the size of those tables, iocsr_config.h
is included build-wide.
This patch wraps all this into a single accessor which takes the scan
chain ID and returns pointer to the table and it's size. All this is
wrapped in wrap_iocsr_config.c board-specific file. The file includes
the iocsr_config.c (!) to access the original tables and transitively
iocsr_config.h . It is thus no longer necessary to include iocsr_config.h
build-wide and the namespace polution is trimmed some more.
Signed-off-by: Marek Vasut <marex@denx.de>
Extract the clock configuration horribleness caused by pll_config.h in
the following manner.
First of all, introduce a few new accessors which return values of
various clocks used in clock_manager.c and use them in clock_manager.c .
These accessors replace those few macros which came from pll_config.h
originally. Also introduce an accessor which returns the struct cm_config
default configuration for the clock manager used in SPL.
The accessors are implemented in a board-specific wrap_pll_config.c
file, whose sole purpose is to include the qts-generated pll_config.h
and provide only the necessary values to the clock manager.
The purpose of this design is to limit the scope of inclusion for the
pll_config.h , which thus far was included build-wide and poluted the
namespace. With this change, the inclusion is limited to just the new
wrap_pll_config.c file, which in turn provides three simple functions
for the clock_manager.c to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Enable the Altera SDRAM driver for the SoCFPGA platform.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Move all the files generated by Quartus into the qts/ subdir of the
board/altera/socfpga dir to make them explicitly separate from the
generic U-Boot code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
P2371-0000 is a P2581 or P2530 CPU board married to a P2595 I/O
board. The combination contains SoC, DRAM, eMMC, SD card slot,
HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
a GPIO expansion header, and an analog audio jack.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
E2220-1170 is a Tegra210 bringup board with onboard SoC, DRAM,
eMMC, SD card slot, HDMI, USB micro-B port, and sockets for various
expansion modules.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_MAX77620_POWER isn't used anywhere. Don't define it in p2571.h.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some devices are bound entirely by probing and do not have the benefit of
a device tree to give them a name. This is very common with PCI and USB. In
most cases this is fine, but we should add an official way to set a device
name. This should be called in the device's bind() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This new command can dump all device resources associated to
each device. The fields in every line shows:
- The address of the resource
- The size of the resource
- The name of the release function
- The stage in which the resource has been acquired (BIND/PROBE)
Currently, there is no driver using devres, but if such drivers are
implemented, the output of this command should look like this:
=> dm devres
- root_driver
- soc
- extbus
- serial@54006800
bfb541e8 (8 byte) devm_kmalloc_release BIND
bfb54440 (4 byte) devm_kmalloc_release PROBE
bfb54460 (4 byte) devm_kmalloc_release PROBE
- serial@54006900
bfb54270 (8 byte) devm_kmalloc_release BIND
- gpio@55000000
- i2c@58780000
bfb5bce8 (12 byte) devm_kmalloc_release PROBE
bfb5bd10 (4 byte) devm_kmalloc_release PROBE
- eeprom
bfb54418 (12 byte) devm_kmalloc_release BIND
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, Devres requires additional 16 byte for each allocation,
which is not so insignificant in some cases.
Add CONFIG_DEVRES to make this framework optional.
If the option is disabled, devres functions fall back to
non-managed variants. For example, devres_alloc() to kzalloc(),
devm_kmalloc() to kmalloc(), etc.
Because devres_head is also surrounded by an ifdef conditional,
there is no memory overhead when CONFIG_DEVRES is disabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
devm_kmalloc() is identical to kmalloc() except that the memory
allocated with it is managed and will be automatically released
when the device is removed/unbound.
Likewise for the other variants.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
In U-Boot's driver model, memory is basically allocated and freed
in the core framework. So, low level drivers generally only have
to specify the size of needed memory with .priv_auto_alloc_size,
.platdata_auto_alloc_size, etc. Nevertheless, some drivers still
need to allocate/free memory on their own in case they cannot
statically know the necessary memory size. So, I believe it is
reasonable enough to port Devres into U-boot.
Devres, which originates in Linux, manages device resources for each
device and automatically releases them on driver detach. With devres,
device resources are guaranteed to be freed whether initialization
fails half-way or the device gets detached.
The basic idea is totally the same to that of Linux, but I tweaked
it a bit so that it fits in U-Boot's driver model.
In U-Boot, drivers are activated in two steps: binding and probing.
Binding puts a driver and a device together. It is just data
manipulation on the system memory, so nothing has happened on the
hardware device at this moment. When the device is really used, it
is probed. Probing initializes the real hardware device to make it
really ready for use.
So, the resources acquired during the probing process must be freed
when the device is removed. Likewise, what has been allocated in
binding should be released when the device is unbound. The struct
devres has a member "probe" to remember when the resource was
allocated.
CONFIG_DEBUG_DEVRES is also supported for easier debugging.
If enabled, debug messages are printed each time a resource is
allocated/freed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, we only have DM_FLAG_ACTIVATED to indicate the device
status, but we still cannot know in which stage is in progress,
binding or probing.
This commit introduces a new flag, DM_FLAG_BOUND, which is set when
the device is really bound, and cleared when it is unbound.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'ranges' property can be used to specify a translation from the system
address to the bus address. Add support for this using the dev_get_addr()
function, which devices should use to find their address.
Signed-off-by: Simon Glass <sjg@chromium.org>
fdt_addr_t is a physical address. It can be either 64-bit or 32-bit,
depending on the architecture. It should be phys_addr_t instead of
u64 or u32. Similarly, fdt_size_t is changed to phys_size_t.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Spring is the first ARM-based HP Chromebook 11. It is similar to snow
and it uses the same Samsung Exynos5250 chip. But has some unusual
features. Mainline support for it has lagged snow (both in kernel and
U-Boot). Now that the exynos5 code is common we can support spring just
by adding a device tree and a few lines of configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that most exynos5250 boards can use the generic exynos5 code, switch
over to it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that exynos5420 boards can use the generic exynos5 code, switch over to
it and remove the old code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Many options are duplicated on the exynos5 boards. Move these to the common
files. Also some options are not used so can be removed.
Tidy this up to make the files easier to maintain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
A video bridge typically converts video from one format to another, e.g.
DisplayPort to LVDS. Add driver model support for these with a simple
interface to control activation and backlight. The uclass supports GPIO
control of power and reset lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports probing and basic register access. It supports the standard
device tree binding and supports driver model. A regulator driver can be
provided also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The existing TPS65090 driver does not support driver model. Add a new one
that does. This can be used as a base for a regulator driver also. It uses
the standard device tree binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.
There are two implementation choices:
1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.
2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.
Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.
The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to be able to transfer a raw I2C message. This
happens when the chip address needs to be set manually, or when the data to
be sent/received is in another buffer.
Add a function to provide access to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Move the flags and struct definitions higher in the file so that we can
reference them with functions declared in the driver model section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a way to dump the contents of an I2C message for debugging purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
It is common for one node to reference another via a phandle. Add support
for obtaining an attached device by this method. As an example, a node may
have a 'power-supply' property which references a regulator, allowing the
driver to turn on its power.
Signed-off-by: Simon Glass <sjg@chromium.org>
Removed NS16550_COM1 #define, not used since there's no SPL for T210
Also changed the number of USB controllers to 1 as only USBD is used.
Signed-off-by: Tom Warren <twarren@nvidia.com>
All T114+ Tegra boards should be using the Kconfig
TEGRA114_SPI switch. Remove it from include/config
and put it into defconfig. Also removed unused
TEGRA114_SPI_CTRLS from T114+ configs.
All Tegra SoCs build OK with this change.
Signed-off-by: Tom Warren <twarren@nvidia.com>
The tegra-common-usb-gadget.h include was causing
some build problems in ci_udc.c with a 64-bit gcc
in an earlier version of the T210 patches, but it
is working fine now, so restore it.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds some config options to the sunxi-common config to enable the USB
download gadget and the fastboot and USB mass storage functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Now that some things were updated in Kconfig, they should be reflected on the
sunxi-common config too.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Most EFI implementations use 64-bit. Add a way to build U-Boot as a 64-bit
EFI payload. The payload unpacks a (32-bit) U-Boot and starts it. This can
be enabled for x86 boards at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to be able to load U-Boot onto a board even if is it already
running EFI. This can allow access to the U-Boot command interface, flexible
booting options and easier development.
The easiest way to do this is to build U-Boot as a binary blob and have an
EFI stub copy it into RAM. Add support for this feature, targeting 32-bit
initially.
Also add a way to detect when U-Boot has been loaded via a stub. This goes
in common.h since it needs to be widely available so that we avoid redoing
initialisation that should be skipped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Improvements to how the payload is built:
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add configuration and Kconfig changes for this board.
Signed-off-by: Ben Stoltz <stoltz@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running U-Boot as an EFI application we cannot relocate since we do not
have relocation information. U-Boot has already been relocated to a suitable
address.
Add a global_data flag to control skipping relocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These are now in the device tree so we don't need to use the CONFIG options.
Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this function does not specify its return value. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When running as an EFI application, U-Boot must request memory from EFI,
and provide access to the boot services U-Boot needs.
Add library code to perform these tasks. This includes efi_main() which is
the entry point from EFI. U-Boot is built as a shared library.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a convention that the generic global_data only occupy the bottom 16 bits
of the flags word, so that there is less chance of a conflict. At present the
x86 flags conflict.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These will be used for efi.h both for U-Boot running as an EFI application
and as a payload. They come from Linux 4.1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI IRQ routing information in the board device tree and enable
writing PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Bayley Bay board is a BayTrail based board. Add this board
with existing baytrail fsp support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On Intel BayTrail SoC, there is a legacy UART (I/O 0x3f8) integrated
into the SoC which is enabled by the FSP. Remove the smsc47x superio
initialization codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch replaces not existing addr_uboot environment variable by
loadaddr at get_uboot_net and burn_uboot_xxx commands. Otherwise these
commands are broken.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
PCIe extends device's configuration space to 4k and provides
extended capability. The patch adds function to find them.
The code is ported from Linux PCIe driver.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC firware version 8.0.0 contains new command flags. This patch
contains modifications in FLIB files to support the new command flags.
Signed-off-by: Itai Katz <itai.katz@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To improve eTSEC performance on LS1021A Rev2.0,
snooping of all transmit frames from memory and
all transmit BD memory accesses in enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable bootscript support in secure boot for establishing
chain of trust on LS1021atwr.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For ls1021a, Reserve secure code in to memory in case OCRAM
is needed by other usage.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since i.MX6UL use A7 core, but not A9 core, we do not need
the erratas for i.MX6UL.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add Kconfig options for USB keyboard and use them for cm-fx6.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Move CONFIG_CMD_* options that can be selected in menuconfig to cm-fx6
defconfig.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement a cm-fx6 specific board_video_skip() to provide the option to not
initialize the display.
The new function does not init display if the environment variable "panel" is
not defined, or if it is set to an unsupported value.
Collateral changes:
- Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific).
- Don't use detect_hdmi(), since env controlled init makes it unnecessary.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
1. Add DDR script for mx6qpsabreauto board.
2. On CPU3 board, enet RGMII tx clock is from internal PLL. Set the GPR5[9]
and init the enet pll output to 125Mhz.
3. On CPU3 board, SW1ABC=VDDSOC_IN, SW2=VDDARM_IN.
Build target: mx6qpsabreauto_config
Boot Log:
U-Boot 2015.07-rc2-00071-gfd985ff (Jun 29 2015 - 22:10:55 +0800)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
PMIC: PFUZE100 ID=0x10
Flash: 32 MiB
NAND: 0 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Note:
In this patch, we still add a new config mx6qpsabreauto_config,
since SPL is not supported now, and IMX_CONFIG is needed at
build time, so add this config. Future, when SPL is converted,
this config can be removed.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Detect the SOC and board variant at runtime and change the dtb name,
but not hardcoding the fdt_file env variable.
Take the following patch as a reference.
Íd58699b157df75f1aa0b363ea9c21add21a0c
"mx6cuboxi: Load the correct 'fdtfile' variable"
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for NOR flash and GPIO/I2C switch control on RevC.
- NOR support
- bank0/bank4 switch
- SD/eMMC switch
- board version
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For running Chain of Trust when doing Secure Boot from NAND,
the Bootscript header and bootscript must be copied from NAND
to RAM(DDR).
The addresses and commands for the same have been defined.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure Boot Target is added for NAND for P3041.
For mpc85xx SoCs, the core begins execution from address 0xFFFFFFFC.
In case of secure boot, this default address maps to Boot ROM.
The Boot ROM code requires that the bootloader(U-boot) must lie
in 0 to 3.5G address space i.e. 0x0 - 0xDFFFFFFF.
In case of NAND Secure Boot, CONFIG_SYS_RAMBOOT is enabled and CPC is
configured as SRAM. U-Boot binary will be located on SRAM configured
at address 0xBFF00000.
In the U-Boot code, TLB entries are created to map the virtual address
0xFFF00000 to physical address 0xBFF00000 of CPC configured as SRAM.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
IFC nand ecc encode and decode mode are not correctly
set in CSOR register during nand initialization.Enable
ecc encode/decode in 4-bit mode
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Based on Venice2, incorporates Stephen Warren's
latest P2571 pinmux table.
With Thierry Reding's 64-bit build fixes, this
will build and and boot in 64-bit on my P2571
(when used with a 32-bit AVP loader).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
All based off of Tegra124. As a Tegra210 board is brought
up, these may change a bit to match the HW more closely,
but probably 90% of this is identical to T124.
Note that since T210 is a 64-bit build, it has no SPL
component, and hence no cpu.c for Tegra210.
Signed-off-by: Tom Warren <twarren@nvidia.com>
ARMv8 requires an architected timer to be present, so it can be used
instead of the Tegra US timer. This allows for better code reuse.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For 64-bit ARM SoCs we rely on non-U-Boot code to bring up the CPU in
AArch64 mode so that we don't need the SPL. Non-cached memory is not
implemented (yet) for 64-bit ARM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This corrects several typos in the comment block as well as some
indentions and nits in the linker_lists.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Provide option to enable uart dcc support for zynqmp
This config can be enabled as per board config file.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move CONFIG_SYS_TEXT_BASE of ZynqMP_ep to its
respective defconfig
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a new config "zynqmp_ep" for ZynqMP instead
of xilinx_zynqmp. This defconfig supports all emulation
platforms of ZynqMP. Also renamed TARGET_XILINX_ZYNQMP
to ARCH_ZYNQMP.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The sysboot and pxe commands currently support either U-Boot formats or
raw zImages. Add support for the AArch64 Linux port's native image format
too.
As with zImage support, there is no auto-detection of the native image
format. Rather, if the image is auto-detected as a U-Boot format, U-Boot
will try to interpret it as such. Otherwise, U-Boot will fall back to a
raw/native image format, if one is enabled.
My belief is that CONFIG_CMD_BOOTZ won't ever be enabled for any AArch64
port, hence there's never a need to differentiate between CONFIG_CMD_
_BOOTI and _BOOTZ at run-time; compile-time will do. Even if this isn't
true, we want to prefer _BOOTI over _BOOTZ when defined, since _BOOTI is
definitely the native format for AArch64.
Change-Id: I83c5cc7566032afd72516de46f4e5eb7a780284a
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We are getting very close to running out of space in SPL, and with the
currently Chrome OS gcc 4.9 we exceed the limit. Add a litle more space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DTS support (CONFIG_OF_LIBFDT) and select
CONFIG_FIT in defconfig.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
using http://git.ti.com/keystone-linux/boot-monitor/trees/master as
reference (tag K2_BM_15.07) the generated files do not have evm
extensions by default. So dont use -evm extension.
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Switch to using zImage instead of uImage. and while at it, start using
bootz as default. While at it, get rid of BOOTIMAGE define and start
using Linux upstream dtb file names.
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Use the defaults defined in DEFAULT_LINUX_BOOT_ENV
Reviewed-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Try to maintain as much commonality by conditionally including stuff
in armv7_common as necessary and removing the common defines from
keystone2 header.
Note: as part of this change, all keystone2 platforms will now start
using the generic u-boot prompt instead of the custom prompt.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
rename the keystone2 common header into an keystone2 architecture
specific header which can then reuse the common ti_armv7 config headers.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
CONFIG_LINUX_BOOT_PARAM_ADDR is not a valid configuration option. Do
just like what the rest of the world does.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit bd2c4522c2 ("ti: armv7: enable EXT support in SPL (using
ti_armv7_common.h)") enabled thumb mode only for SPL builds, however,
All TI armv7 platforms do support thumb, and there is no reason why the
space savings cannot be exploited for u-boot as well.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
TI armv7 based SoCs are based on two architectures - one based on OMAP
generation architecture and others based on Keystone architecture.
Many of the options are architecture specific, however a lot are common
with v7 architecture. So, step 1 will be to move out OMAP specific stuff
from ti_armv7_common into a ti_armv7_omap.h header which is then used
by all the relevant architecture headers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Mainline Linux kernel commit
338a6aaabc02fa63b70441dd0e1b70aea64673c6 (ARM: dts: Introduce
STM32F429 MCU) in arch/arm/boot/dts/stm32f429.dtsi
requires U-Boot to set system clock to 180 MHz.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
Read device unique ID and set environment variable "serial#".
Value would then be passed to kernel through DTB.
To read ID from DTB, kernel is required to have commit:
3f599875e5202986b350618a617527ab441bf206 (ARM: 8355/1: arch: Show
the serial number from devicetree in cpuinfo)
This commit is already mainline since v4.1-rc1.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: Albert Aribaud <albert.u.boot@aribaud.net>
To: Tom Rini <trini@konsulko.com>
To: Kamil Lulko <rev13@wp.pl>
Cc: u-boot@lists.denx.de
The config file for the siemens-am33x-common was using OMAP_I2C_STANDARD, which
is defined in a header that is not included in the config header. In most cases,
it was being included by the code using CONFIG_SYS_OMAP24_I2C_SPEED, but it
might not always be the case.
In particular, when introducing I2C SPL support in omap-common's boot-common.c,
the header is missing and including it breaks other devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There are only two SoC-specific headers for this architecture:
- arch/nds32/include/asm/arch-ag101/ag101.h
- arch/nds32/include/asm/arch-ag102/ag102.h
Those two have different file names, so there is no advantage to
include them via symbolic linked directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Palmas power support is required for OMAP5 devices such as the OMAP5 uEVM, that
need to e.g. enable MMC power at SPL stage.
This is especially important when booting from a peripheral (such as USB, UART),
where the bootrom will not enable power for the MMC device that will hold the
main U-Boot.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add thermal support so that we can see the following message on boot:
CPU: Industrial temperature grade (-40C to 105C) at 33C
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Entering the maximum number of characters defined by CONFIG_SYS_CBSIZE into
the console and hitting enter afterwards, causes a hang in the system because
CONFIG_SYS_PBSIZE is not capable of storing the extra characters of the error
message:
"Unknown command '' - try 'help'".
Use the default CONFIG_SYS_PBSIZE definition from config_fallbacks.h to solve
this problem.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
It seems that many comments were copied from the I2C uclass, so adjust
the comments for the thermal class.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds support for the "OHB System AG" baseboard
with is equipped with the TQMa6S SoM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Stefano Babic <sbabic@denx.de>
Start using the new Kconfig options which are available for these now,
and simply always enable them by selecting them as sunxi builds always
include USB support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the configuration options to boot via SDIO/MMC on the
Marvell DB-88F6820-GP Armada A38x board. The default boot device
is still SPI NOR flash.
To enable MMC booting on this board 2 things need to be changes:
a) Change kwbimage.cfg
BOOT_FROM sdio
b) In the config header select
#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD
The generated image needs to be copied to the first bootable MMC
partition:
dd if=u-boot-spl.kwb of=/dev/sdX1
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The command "run tftpboot" downloads some files onto the RAM
via TFTP and boots the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the environment variables "norboot" and "nandboot" only
work with CONFIG_FIT, but we do not want to depend on CONFIG_FIT to
boot the kernel.
This commit adds environments useful for booting Linux with separate
uImage + ramdisk + DTB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds SPL support for the Marvell DB-88F6820-GP board.
With this change, the bin_hdr from the original Marvell U-boot
is not needed any more on this board. The sources from bin_hdr
(SERDES/PHY and DDR setup) are now integrated in mainline
U-Boot. And this patch enables them for this board.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently, kzalloc() returns zero-filled memory, while kmalloc()
simply ignores the second argument and never fills the memory
area with zeros.
I want kmalloc(size, __GFP_ZERO) to behave as kzalloc() does,
which will make it easier to add more memory allocator variants.
With the introduction of __GFP_ZERO flag, going forward, kzmalloc()
variants can fall back to kmalloc() enabling the __GFP_ZERO flag.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
The vzalloc(size) is equivalent to kzalloc(size, 0). Move it to
include/linux/compat.h as an inline function in order to avoid the
function call overhead.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
The macro cpu_relax() is defined by several headers in different
ways.
arch/{arm,avr32,mips}/include/asm/processor.h defines it as follows:
#define cpu_relax() barrier()
On the other hand, include/linux/compat.h defines it as follows:
#define cpu_relax() do {} while (0)
If both headers are included from the same source file, the warning
warning: "cpu_relax" redefined [enabled by default]
is displayed.
It effectively makes it impossible to include <linux/compat.h>
from some sources. Drop the latter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.
This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Each USB download function command calls board_usb_init before registering the
USB gadget and board_usb_cleanup after de-registering it. On devices currently
using fasboot, musb-new is usually initialized earlier, but some other boards
might need the board_usb_init call to properly initialize musb-new.
This requires adding an argument (the USB controller index) to the fastboot
command, as it is currently done with other USB download gadget functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Move USB controller Base address mapping from ls102xa immap
to fsl xhci header. This is required to remove any warnings when
controller base addresses are mapped for multiple platforms
in their respective files.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Some drivers may want to implement this method for some of their devices but
not for others. So it is not possible to just leave the operation out of
the table. Drivers could get around this by masquerading as two separate
drivers but that seems unpleasant.
Allow the driver to return an error when it does not want to process the
write_hwaddr() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that the RTL8169 driver warning is fixed we can drop this. The incorrect
value is causing problems with USB EHCI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In Linux USB_DEVICE() is used to declare a USB device by vendor/device ID.
We should follow the same convention in U-Boot. Rename the existing
USB_DEVICE() macro to U_BOOT_USB_DEVICE() and bring in the USB_DEVICE()
macro from Linux for use in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present USB Ethernet does not work with CONFIG_DM_ETH. Add driver model
support to this feature, so that it can work alongside other Ethernet
devices with driver model.
It was found that quite a bit of code is common in most of the USB Ethernet
drivers. Add this code to the common layer to reduce the amount of duplicate
code needed in USB Ethernet drivers when CONFIG_DM_ETH is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some devices can take a long time to work out whether they have a new packet
or now. For example the ASIX USB Ethernet dongle can take 5 seconds to do
this, since it waits until it gets a new packet on the wire before allowing
the USB bulk read packet to be submitted.
At present with driver mode the Ethernet receive code reads 32 packets. This
can take a very long time if we must wait for all 32 packets. The old code
(before driver model) worked by reading a single set of packets from the USB
device, then processing all the packets with in. It would be nice to use
the same behaviour with driver model.
Add a flag to the receive method which indicates that the driver should try
to find a packet if available, by consulting the hardware. When the flag is
not set, it should just return any packet data it has already received. If
there is none, it should return -EAGAIN so that the loop will terminate.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to find the full PCI address (bus, device and
function) for a PCI device. Add a function to provide this.
Adjust the existing code to use this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all PCI devices must be present in the device tree in order to
be used. Many or most PCI devices don't require any configuration other than
that which is done automatically by U-Boot. It is inefficent to add a node
with nothing but a compatible string in order to get a device working.
Add a mechanism whereby PCI drivers can be declared along with the device
parameters they support (vendor/device/class). When no suitable driver is
found in the device tree the list of such devices is consulted to determine
the correct driver. If this also fails, then a generic driver is used as
before.
The mechanism used is very similar to that provided by Linux and the header
file defintions are copied from Linux 4.1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Allow usb uclass host drivers to implement usb_reset_root_port, this is
used by single port usb hosts which do not emulate a hub, such as otg
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
These functions are useful to remove all children from an usb bus before
rescanning the bus. Give them a better name and export them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an usb_device parameter to usb_reset_root_port so that it knows which
root-port it is resetting. This is necessary for proper device-model support
for usb_reset_root_port.
Also remove a duplicate declaration of usb_reset_root_port() from usb.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop the unneeded portnr function argument, the portnr is part of the
usb_device struct which is passed via the dev argument.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The device-model usb_legacy_port_reset function calls the device-model
usb_port_reset function which is a 1 on 1 copy of the non dm
usb_legacy_port_reset and this is the only use of usb_port_reset in all
of u-boot.
Drop both, and alway use the usb_legacy_port_reset() version in
common/usb.c .
Also while at it make it static as it is only used in common/usb.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Some functions can return ERR_PTR(errval). Add a unit test macro to check
that no error is returned in a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
We normally use -ENODEV for a missing device, rather than -ENOENT. The
latter is reserved for when we have a device but cannot find something
within it.
Also avoid looking at the root LED device since it is only a container.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new reset_walk_halt() function to cause a reset and then halt on
failure. The reset_walk() function returns an error code.
This is needed for testing since otherwise U-Boot will halt in the middle
of a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should guide people more strongly towards device tree to avoid the
proliferation of platform data structures. Add documentation to the driver
model README, and also the platform data header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Clocks are an important feature of platforms and have become increasing
complex with time. Most modern SoCs have multiple PLLs and dozens of clock
dividers which distribute clocks to on-chip peripherals.
Some SoC implementations have a clock API which is private to that SoC family,
e.g. Tegra and Exynos. This is useful but it would be better to have a
common API that can be understood and used throughout U-Boot.
Add a simple clock API as a starting point. It supports querying and setting
the rate of a clock. Each clock is a device. To reduce memory and processing
overhead the concept of peripheral clocks is provided. These do not need to
be explicit devices - it is possible to write a driver that can adjust the
I2C clock (for example) without an explicit I2C clock device. This can
dramatically reduce the number of devices (and associated overhead) in a
complex SoC.
Clocks are referenced by a number, and it is expected that SoCs will define
that numbering themselves via an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is common for system reset to be available at multiple levels in modern
hardware. For example, an SoC may provide a reset option, and a board may
provide its own reset for reasons of security or thoroughness. It is useful
to be able to model this hardware without hard-coding the behaviour in the
SoC or board. Also there is a distinction sometimes between resetting just
the CPU (leaving GPIO state alone) and resetting all the PMICs, just cutting
power.
To achieve this, add a simple system reset uclass. It allows multiple devices
to provide reset functionality and provides a way to walk through them,
requesting a particular reset type until is it provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an spl_init() function that does basic init such that board_init_f() can
use simple malloc(), device tree and driver model. Each one is set up only
if enabled for SPL.
Note: We really should refactor SPL such that there is a single
board_init_f() and rename the existing weak board_init_f() functions
provided by boards, calling them from the single board_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
Split out the code in fdtdec which finds a number at the end of a string. It
can be useful in other situations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an implementation of RC4. This will be used by Rockchip booting but may
be useful in other situations.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for a driver which sets up DRAM and can return information about
the amount of RAM available. This is a first step towards moving RAM init
to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a common requirement to update some PMIC registers. Provide some
simple convenience functions to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The device tree provides information about which regulators should be
on at boot, or always on. Use this to set them up automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The regulator_autoset() function mixes printf() output and PMIC adjustment
code. It provides a boolean to control the output. It is better to avoid
missing logic and output, and this permits a smaller SPL code size. So
split the output into a separate function.
Also rename the function to have a by_name() suffix, since we would like
to be able to pass a device when we know it, and thus avoid the name
search.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Decide when the regulator is set up whether we want to auto-set the voltage
or current. This avoids the complex logic spilling into the processing code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
It took a little while to figure this out, so this patch adds documentation
to help the next person who needs to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add basic support for MMC, providing a uclass which can set up an MMC
device. This allows MMC drivers to move to using driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for LEDs, so that these can be controlled by the device
tree and activated when needed. LEDs are referred to by their label.
This implementation requires a driver for each type of LED (e.g GPIO, I2C).
Signed-off-by: Simon Glass <sjg@chromium.org>
Many SoCs have a number of system controllers which are dealt with as a
group by a single driver. It is a pain to have to add lots of compatible
strings and/or separate drivers for each. Instead we can identify the
controllers by a number and request the address of the one we want.
Add a simple implementation of this which can be used by SoC driver code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple implementaton of register maps, supporting only direct I/O
for now. This can be enhanced later to support buses which have registers,
such as I2C, SPI and PCI.
It allows drivers which can operate with multiple buses to avoid dealing
with the particulars of register access on that bus.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function can be used for testing to manually request a GPIO for use,
without resorting to the legacy GPIO API.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some rare cases it is useful to be able to locate a device given a device
tree node offset. An example is when you have an alias that points to a node
and you want to find the associated device. The device may be SPI, MMC or
something else, but you don't need to know the uclass to find it.
Add a function to do a global search for a device, given its device tree
offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
In SPL it is sometimes useful to be able to obtain a dump of the current
driver model state. Since commands are not available, provide a way to
directly call the functions to output this information.
Adjust the existing commands to use these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not actually help any current arch. For x86 it makes it harder
to call (requires stack) and for ARM it has no effect. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot uses structures for hardware access so it is important that these
structures are correct. Add a way of asserting that a structure member is
at a particular offset. This can be created using the datasheet for the
hardware.
This implementation uses Static_assert() since BUILD_BUG_ON() only works
within functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
These have been sent upstream but not accepted to libfdt. For now, bring
these into U-Boot to enable fdtgrep to operate. We will use fdtgrep to
cut device tree files down for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Property names are stored in a string table. When a node property is
removed, the string table is not updated since other nodes may have a
property with the same name.
Thus it is possible for the string table to build up a number of unused
strings. Add a function to remove these. This works by building a new device
tree from the old one, adding strings one by one as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Offer to display the available image types in help. Also, rather than
hacking the genimg_get_type_id() function to display a list of types,
do this in the tool. Also, sort the list.
The list of image types is quite long, and hard to discover. Print it out
when we show help information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable DSPI flash related configurations for LS2085ARDB.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Linux itb image size has been increased from 30MB.
So updating kernel_size to 40MB in env variable.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increases the kernel size supported for LS2085A platforms:-
- Update environment variables
- Add ramdisk_size in bootargs env variable
- Define CONFIG_SYS_BOOTM_LEN to 64MB
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Primary Mux on I2C1 controller has slave address as 0x75.
So update its address.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable "date" command for QDS and RDB boards
Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Looks like this comment was copied from that of
fdt_get_string_index().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes: 5094eb408a ("fdt: Add functions to retrieve strings")
Acked-by: Simon Glass <sjg@chromium.org>
Avoid clearing the reg property in the memory DT node if no memory
banks have been specified for a board (CONFIG_NR_DRAM_BANKS == 0).
This allows boards to let U-Boot skip the DT memory tinkering in case
other firmware has already setup the node properly before.
This should be safe as all callers of fdt_fixup_memory_banks that use
a computed <banks> value put at least 1 in there.
Add some documentation comments to the header file.
Signed-off-by: Andre Przywara <osp@andrep.de>
Acked-by: Simon Glass <sjg@chromium.org>
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable a SPI environment and store it in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Introduce a new method 'get_count' in the UCLASS_CPU ops to get
the number of CPUs in the system.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 09c3280754 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch enabled the USB/EHCI support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Configure and enable the SATA/SCSI (AHCI) support for the Marvell
DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds MMC/SDIO support to the Marvell DB-88F6820-GP board
configuration. Including support for the common partitions and
filesystems.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
According to README.mxc_ocotp the OCOTP is a stanard i.MX6 SoC feature
so centralise the config in mx6_common.h so functionality is standard
across all boards
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
When compling under 64bit platforms, there are lots of warnings,
like:
drivers/block/ahci.c:114:18: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
u8 *port_mmio = (u8 *)probe_ent->port[port].port_mmio;
^
drivers/block/ahci.c: In function ?.hci_host_init?.
drivers/block/ahci.c:218:49: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
probe_ent->port[i].port_mmio = ahci_port_base((u32) mmio, i);
......
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Baltos has USB0 connected to a USB hub and thus is host-only. USB1
is connected to microUSB connector and thus should use OTG mode.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Because it is possible for the MTD number to change, causing a
filesystem mount failure, we should use the volume name instead
of the MTD number and let Linux resolve the correct one.
Signed-off-by: Mike Scherban <m-scherban@ti.com>
On STM32F429 gpio PC6/PC7 can be allocated for USART6, as
reported in the comment.
But current code in
drivers/serial/serial_stm32.c
uses a different gpio mapping (PG14/PG9) for USART6.
Fix the comment to match current code in the driver.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
To: u-boot@lists.denx.de
To: Kamil Lulko <rev13@wp.pl>
Cc: Tom Rini <trini@konsulko.com>
Use one mtd partition for rootfs and configuration by
means of ubi volumes and get rid of configuration partition.
We can use partition layout for both 256MB and 512MB flash.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
Specify proper U-Boot offset, enable prefetch mode,
increase bootm size and add FIT fallback, if board_name
is not present in kernel-fit.itb image.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
This action is need to make I2C communication with PMIC
stable for low temperature. Print current I2C speed in
SPL for visual control.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
This also came from Linux - according to this thread it has a GPL v2
license like arch/arm/mach-omap2/mux.h:
http://lists.denx.de/pipermail/u-boot/2015-June/217827.html
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of selecting REGEX when NET is enabled, make it the default, but
allow boards that are tiny to disable it and lose functionality on all
but the first Ethernet adapter.
cm-bf548, bf538f-ezkit, and bf533-stamp need this. None appear to have
more than one Ethernet interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch uses generic 'load' command instead of 'fatload' for 'loadbootscript', 'loadimage' and 'loadfdt' for mx53loco board.
This allows to use EXT partition instead of FAT, while keeping FAT compatibility.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Jason Liu <r64343@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
This patch does all the board configurations required to use the qspi
controller & attached spi flash memory.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
CONFIG_OF_SEPARATE is default define with CONFIG_OF_CONTROL, removing
this define from the board file to avoid multiple definition warning.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Increase console IO buffer size to 1024 from the previous value of 256.
The previous value was too short for editing environment variables like
ubiboot from the console.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Enable Driver Model SPI for ls1021atwr board.
DSPI and QSPI only be enabled when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable Driver Model SPI for ls1021aqds board.
DSPI and QSPI is enabled only when boot from QSPI.
DSPI and QSPI are compatible under Driver Model SPI.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
By default on this platform, u-boot loads data into high memory
in the range of 0x7Fxxxxxx, which generates a data abort when the
kernel tries to read it. Config the u-boot environment to load
the device tree and initrd image into lower memory to make them
accessible to the kernel.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
These options were merged into mx6_common and were seemingly missed
in mx6cuboxi so drop the duplicates
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Update new naming scheme.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
rastaban is a draco version with more flash, more RAM
and faster CPU. Number of partitions is the same but
rootfs partition is different.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard-X15 uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
add cpsw ethernet boot mode support to download spl and
u-boot.img via tftp protocol. Also adding a seperate config
for ethernet boot mode as the default build falcon mode and
environment on MMC is defined for ethernet boot mode
environment should be set to nowhere.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
While booting via usb host mode, ROM uses DMA to copy MLO over USB so
ARM internal RAM cannot be used. Adding USB host boot support by
introducing new config target which sets SPL_TEXT_BASE to OCMC ram.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With 1.2 silicon this is now the documented starting usable point for
downloading images to (and corrects a problem with peripheral booting
with prior silicon). Prior silicon is OK using this address as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested on Pandaboard (rev. A3) and Beagleboard xM (rev. B).
Compilation tested on TI armv7 boards and OMAP boards from other vendors.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
updates for the siemens am335x based boards:
- draco: add delay for DDR3 configuration
- change MTD partition layout and add a possibility
to redefine MTD layout in board header.
- move ubi support to common header file
- draco: improve dtb naming
- draco: set CONFIG_SYS_CBSIZE to 1024
- add generic env based led
Leds can now be defined in Environment
- add generic env based dfu button
Which gpio is used for the dfu button can be defined
through the Environment
- set MACH_TYPE only if defined
- draco: increase CPU freq to 300MHz
- Add time command to siemens am33xx boards
- DDR3: increase default tRFC
- draco: enable pullup for DFU and ERST pin
- change print format DDR3
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
There is no harm in declaring the function prototypes even if nothing
implements them, and when CONFIG_DM_USB=y the various usb functions are
available regardless of any controller drivers being enabled.
This fixes compile warnings due to missing prototypes on ARCHs where
the ARCH Kconfig always enables CONFIG_DM_USB and various usb drivers.
One could argue that in the case of no controllers CONFIG_DM_USB should not
be set, but this problem is typically seen during bringup of boards which
do actually have usb controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With the change to make sure that CONFIG_CMD_NET is enabled this board
no longer fits into the linker script:
powerpc-linux-ld.bfd: section .resetvec loaded at [fffffffc,ffffffff] overlaps section .u_boot_list loaded at [ffffff58,00000723]
powerpc-linux-ld.bfd: u-boot: section .resetvec lma 0xfffffffc adjusted to 0x724
powerpc-linux-ld.bfd: u-boot: section `.resetvec' can't be allocated in segment 0
LOAD: .data.init .text .rodata .reloc .data .u_boot_list .resetvec
powerpc-linux-ld.bfd: final link failed: File truncated
Drop CONFIG_SYS_LONGHELP to free up space.
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
since we have now various processor-speeds it isn't useful anymore to
preinitialize kernels-delay loop.
Rather we want the kernel to calibrate it on every boot.
This wastes around 80ms boottime but is compatible to all CPU-speeds.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Currently there is no default value for NETARGS if CONFIG_CMD_NET=y isn't set.
This results in build errors which was first discovered when trying to run
make env.
By defining a blank NETARGS these errors can be avoided.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Tested-by: Maxin B. John <maxin.john@enea.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since the tam3517 base board has a 16bit wide nand connected to
the gpmc, enable the prefetch mode, since that is now supported.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: pekon gupta <pekon@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
In the cases where we make use of environment in SPL we do not need
these defaults compiled in and available. These are taking up space
that in some cases now prevent linking, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
Vision Systems's Baltos is based on AM335x SoC
from Texas Instruments. This patch adds support
such Industrial PCs in mainline u-boot.
[ balbi@ti.com: updated original patch to current u-boot ]
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Now all the AVR32 boards have been converted into Generic Board.
Select it in Kconfig and clean up defines in header files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
On AM437x-GP Evm there is 2GB of DDR3 memory available as stated in
AM437x GP EVM HardwareUser's guide http://www.ti.com/lit/ug/spruhw7/spruhw7.pdf.
But MAX_RAM_BANK_SIZE is defined as 1GB.
Fixing MAX_RAM_BANK_SIZE to 2GB on AM43xx.
Reported-by: Shivasharan Nagalikar <shivasharan.nagalikar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable booting from NAND on the am437xx-evm.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use the correct partition names from with the Device Tree blob
and the kernel is picked up. Also use partition name instead of
number for the root filesystem in the kernel boot arguments.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We almost always use UBIFS for user accessible NAND file systems and
the UBIFS file system might contain more than one volume within the
single NAND partition. The last NAND partition is therefore more
appropriately named as "NAND.file-system" instead of "NAND.rootfs"
The Linux kernel (as of v3.16) also uses "NAND.file-system" to name the
last NAND partition. This patch makes the partition name consistent
between u-boot and the kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable full 48-bit LBA48 data reads by passing the upper word of the
LBA block pointer in bytes 9 and 10 of the FIS.
This allows uboot to load data from any arbitrary sector on a drive
with 2 or more TB of available data connected to an AHCI controller.
Signed-off-by: Mark Langsdorf <mark.langsdorf@gmail.com>
Signed-off-by: Andre Przywara <osp@andrep.de>
[trini: Make use of CONFIG_SYS_64BIT_LBA in a few places to drop
warnings on platforms that don't enable that feature ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling IO delay recalibration sequence for DRA7 EVM.
UART and I2C are configured before IO delay recalibration sequence
as these are used earlier and safe to use.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Allow SPL to be built with this option so that we can support device tree
control. Disable the simple bus for now in SPL. It may be needed later.
Signed-off-by: Simon Glass <sjg@chromium.org>
