On LS1043A rev1.0 there are 4 interrupt pins for INTx, and on
rev1.1 there is only 1 for INTx, so the current fixup is inverse
of the fact.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1043A/LS1023A 23x23 package silicon has different SVR:VAR_PER.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
update TFABOOT defconfig for SD boot on below NXP chasis2
and chasis3 platforms:
ls1043a, ls1046a, ls1088a and ls2088a.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Patch fixes build error when enabling CONFIG_ENV_IS_IN_SPI_FLAS
and CONFIG_ENV_IS_IN_MMC at the same time mentioned issue in
below link:
Refer: https://lists.denx.de/pipermail/u-boot/2018-February/319565.html
build error when enabling CONFIG_ENV_IS_IN_SPI_FLASH and
CONFIG_ENV_IS_IN_MMC at the same time.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls2088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- remove EL3 specific erratas for TFABOOT
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088aqds_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TFABOOT support includes:
- ls1088ardb_tfa_defconfig to be loaded by trusted firmware
- environment address and size changes for TFABOOT
- MC address changes for TFABOOT
- define BOOTCOMMAND for TFABOOT
- ifc chip select changes for TFABOOT
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restore the legacy flow along with TFABOOT flow for
IFC configuration.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Fixes for TFABOOT framework
- update eMMC bootsrc to SD_MMC
- Increase buffer size for mcinitcmd from 256 to 512
- Fix mcinitcmd and bootcmd for Secure Boot
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This fixes 'arch_lmb_reserve()' for ARM that tries to detect in which
DRAM bank 'sp' is in.
This code failed if a bank was at the end of physical address range
(i.e. size + length overflowed to 0).
To fix this, calculate 'bank_end' as 'size + length - 1' so that such
banks end at 0xffffffff, not 0.
Fixes: 15751403b6 ("ARM: bootm: don't assume sp is in DRAM bank 0")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This fixes CVE-2018-18439 ("insufficient boundary checks in network
image boot") by using lmb to check for a valid range to store
received blocks.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: Always build lib/lmb.o on LMB and lib/fdtdec.o on OF_LIBFDT]
Signed-off-by: Tom Rini <trini@konsulko.com>
lmb.h includes an extern declaration of "struct lmb lmb;" which
is not used anywhere, so remove it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This fixes CVE-2018-18440 ("insufficient boundary checks in filesystem
image load") by using lmb to check the load size of a file against
reserved memory addresses.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds two new functions, lmb_alloc_addr and
lmb_get_unreserved_size.
lmb_alloc_addr behaves like lmb_alloc, but it tries to allocate a
pre-specified address range. Unlike lmb_reserve, this address range
must be inside one of the memory ranges that has been set up with
lmb_add.
lmb_get_unreserved_size returns the number of bytes that can be
used up to the next reserved region or the end of valid ram. This
can be 0 if the address passed is reserved.
Added test for these new functions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
boot_fdt_add_mem_rsv_regions() adds reserved memory sections to an lmb
struct. Currently, it only parses regions described by /memreserve/
entries.
Extend this to the more commonly used scheme of the "reserved-memory"
node.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
lmb_add_region handles overlapping regions wrong: instead of merging
or rejecting to add a new reserved region that overlaps an existing
one, it just adds the new region.
Since internally the same function is used for lmb_alloc, change
lmb_add_region to reject overlapping regions.
Also, to keep reserved memory correct after 'free', reserved entries
created by allocating memory must not set their size to a multiple
of alignment but to the original size. This ensures the reserved
region is completely removed when the caller calls 'lmb_free', as
this one takes the same size as passed to 'lmb_alloc' etc.
Add test to assert this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The lmb code fails if base + size of RAM overflows to zero.
Fix this by calculating end as 'base + size - 1' instead of 'base + size'
where appropriate.
Added tests to assert this is fixed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add basic tests for the lmb memory allocation code used to reserve and
allocate memory during boot.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The spi_flash_read_env function is a wrapper over spi_flash_read, which
enables the env to read multiple flash page size from flash until '\0\0'
is read or the end of env partition is reached. Instead of reading the
entire env size. When it reads '\0\0', it stops reading further the env
and assumes that the rest of env is '\0'.
This is an optimization for large environments that contain few bytes
environment variables. In this case it doesn't need to read the entire
environment and only few pages.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Each ECC layout consumes about 2984 bytes in the .data section. Allow
to disable the default ECC layouts if a driver is known to provide its
own ECC layout.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Set the correct power-up state (default-state) of the green power LED.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With the new SPI NOR framework in v4.19, we need to adapt the MTD parts
so that the kernel cmdline parameter "mtdparts=" uses the correct naming
for the devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Fix the Kconfig warning to not use CONFIG_OF_EMBED in defconfigs.
Based on https://patchwork.ozlabs.org/patch/1019791/
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add board support and configuration for Jaguar2 SOC family.
The detection of the board type in this family is based on the phy ids.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
As the Ocelot and Luton SoCs, this family of SoCs are found
in Microsemi Switches solution.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common
to support new numbe of pins and remove any platform dependency from
mscc-common.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Do not build write support, unless it's enabled.
In the SPL case, this change will typically remove
precious bytes (as write support is most often
not needed in SPL).
This is important on this platform, where the maximum
SPL size is 14 KiB.
With gcc v7.3, this change saves 144 bytes producing:
size spl/u-boot-spl
text data bss dec hex filename
9240 752 712 10704 29d0 spl/u-boot-spl
To make the code easier to compile-out and more
readable, a pair of read_data/write_data helpers are created.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use CONFIG_IS_ENABLED(BLK) instead of CONFIG_BLK,
in order to fix the following build issues when
CONFIG_SPL_MMC_WRITE is selected:
drivers/mmc/mmc_write.c:69:7: error: conflicting types for 'mmc_berase'
ulong mmc_berase(struct udevice *dev, lbaint_t start, lbaint_t blkcnt)
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:39:7: note: previous declaration of 'mmc_berase' was here
ulong mmc_berase(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt);
^~~~~~~~~~
drivers/mmc/mmc_write.c:187:7: error: conflicting types for 'mmc_bwrite'
ulong mmc_bwrite(struct udevice *dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:37:7: note: previous declaration of 'mmc_bwrite' was here
ulong mmc_bwrite(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
Discard ABI related sections which are not required for debugging.
Rearrange debug sections similar to Linux. Remove the remaining
explicitely specified sections in the unused part because those
sections are not created anymore or because the linker puts them
by default at the end of the ELF binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver on the MSCC
VCoreIII 'ocelot' SOC, and add gpio-leds nodes to the pcb123 and
pcb120 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver, and add gpio-leds
nodes to the 'luton' pcb090 and pcb091 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
This add device tree binding documentation for the MSCC serial GPIO
driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
