Update the TPM description to include the interrupt mechanicm since this
is useful to know. Also add a warning if the TPM cannot be found and a
debug line if it succeeds.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the Cr50 starts up it doesn't have a valid locality. The driver sets
it to -1 to indicate that. Tracking this allows cr50_i2c_cleanup() to
avoid releasing a locality that was not claimed.
However the helper functions that generate the flags use a u8 type which
cannot support -1, so they return a locality of 0xff.
Fix this by updating the type. With this, 'tpm startup TPM2_SU_CLEAR'
works as expected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch adds support for MTK SPI NOR controller, which you
can see on mt7622 & mt7629.
1. This controller is designed only for SPI NOR. We can't adjust
its bus clock dynamically. Set clock in dts instead.
2. This controller only supports 1-1-1 write mode.
3. Remove mtk_snor_match_read() since upper SPI-MEM layer already
handles command.
4. sf read/write/update commands are tested with this driver.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
This is a basic driver for the ultra-low-power Abracon AB x80x series
of RTC chips. It supports in particular, the supersets AB0805 and AB1805.
It allows reading and writing the time, and enables the supercapacitor or
battery charger.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Set this flag so that it is available to those looking at the device. For
non-removable devices there is no need to check for insertion/removable
since the media can never change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present if an eMMC part is in the system, the ACPI table generated
will include information about that, as well as the SD card. We only need
to include the SD card, since it has a card-detect GPIO. Use a different
compatible string for each option, and add code only for the SD card.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
In some cases so much of the framebuffer is updated that it is not worth
copying the changes piece by piece to the copy framebuffer. Add a function
to copy the whole thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch completely removes CONFIG_PCI_ENUM_ONLY from the PCI code as
it is not configured for any board (any more). With this removal, some
PCI related files get cleaned up a bit.
Additional, dm_pciauto_setup_device() is now static, as it's not
referenced from any code outside of this C file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit add an option TPL_BOOTCOUNT_LIMIT to
use bootcount on TPL.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
The phydev structure has a PHY OF node pointer in it, use that OF node
first when looking up PHY OF node properties, since that is likely the
correct PHY OF node pointer. If the pointer is not valid, which is the
case e.g. on legacy DTs, fall back to parsing MAC ethernet-phy subnode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Add phy driver support for MACs embedded inside Cortina Access SoCs
Signed-off-by: Abbie Chang <abbie.chang@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Tom Rini <trini@konsulko.com>
CC: Aaron Tseng <aaron.tseng@cortina-access.com>
Moved out PHY specific code out of Cortina NI Ethernet driver
and into a Cortina Access PHY interface driver
Add some missing address translations from virtual address in local DRAM
to physical address, which is needed for the DMA transactions to work
correctly.
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Using (dm_)pci_virt_to_mem() is incorrect to translate the virtual
address in local DRAM to a physical address. The correct macro here
is virt_to_phys() so switch to using this macro.
As virt_to_bus() is now not used any more, this patch also removes
both definitions (DM and non-DM).
This issue was detected while testing the e1000 driver on the MIPS
Octeon III platform, which needs address translation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
bus_to_phys() is defined but not referenced at all. This patch removes
it completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Value pcie->dev in function pcie_advk_probe() is not initialized yet
so use dev as argument for dev_dbg()/dev_warn().
Function pcie_advk_wait_pio() itself prints error message on failure
so do not print duplicate error message in caller.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
To check if some output characters are waiting either in Transmitter
Holding Register or Transmitter Shift Register we need to look at
TX_EMPTY bit of UART Status Register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure an IO region and window for PNP identical to how MEM region is
set up. Linux does this only if the DT defines a pcie-io-aperture
property for the SOC, but since all supported boards do this should not
be needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
On my DS414, some PCI devices return odd values when probing BAR sizes.
An obvious case is all-ones response, the Linux driver
(drivers/pci/probe.c) catches those explicitly and a comment explains
that either bit 0 or bit 1 must be clear (depending on MEM or IO type).
Other BARs return e.g. 0xfff0000f or 0xfff00004 and thus manage to break
size calculation due to the "middle" zeroes. Mitigate that copying more
or less what Linux does and do a "find least bit set".
Signed-off-by: Phil Sutter <phil@nwl.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change extends previous commit 061c6d1b23 ("arm: mvebu: Espressobin:
Detect presence of emmc at runtime") and when emmc is not present then emmc
is removed from U-Boot DM and corresponding slot is disabled. Therefore on
Espressobin board without soldered emmc, state of emmc hw should be same as
if emmc was disabled in DTS.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Stefan Roese <sr@denx.de>,
Reviewed-by: Stefan Roese <sr@denx.de>
H616 pinctrl is no different configuration wise than others, so just add
compatible for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far the only difference between the various Allwinner MMC controller
we are concerned about is the mod clock register offset.
This is actually not directly related to the MMC controller IP, but an
integration choice, dependent on the SoC this appears in.
To avoid becoming trapped with some compatible fallback strings, let's
remove the whole struct sunxi_mmc_variant, and replace this with a SoC
based choice, which we can derive from the CONFIG_MACH_SUNx_y symbols.
This will later simplify H616 support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
While currently none of the newer Allwinner SoCs currently has I2C
support implemented in U-Boot, this will change soon. mvtwsi driver is
good as it is for them except one macro. Update it to be ready once I2C
support lands for those SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This PMIC can be found on H616 boards and it's very similar to AXP805
and AXP806.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far all GBit users of the sun8i-emac driver were using the "rgmii"
PHY mode, even though this turns out to be wrong. It just worked because
the PHY driver doesn't do the proper setup (yet).
In fact for most boards the "rgmii-id" or "rgmii-txid" PHY modes are the
correct ones.
To allow the DTs to describe the phy-mode correctly, and to stay
compatible with Linux, at least allow those other RGMII modes in the
driver.
This avoids breakage if mainline DTs will be synced with U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
Add DM_FLAG_PRE_RELOC flag for reset-mtmips to make sure this driver can
be probed before relocation even if u-boot,dm-pre-reloc is not present
in the dts.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver does not set the value of plat->cfg.f_max, which
results in that MMC framework will always run at the lowest frequency.
This patch sets plat->cfg.f_max to the maximum allowed frequency, which
equals to the source clock frequency.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The driver is missing pad control settings (pad delay and pad conf) for
the mt7620 and mt76x8. Although mt76x8 still works well, mt7620 will
encounter CRC error on data transfers.
This patch adds default pad control settings for mt7620_compat.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
It turns out that the sclk cycles used by mt7620/mt7628 is the same as
other chips (20 bits, 1048576), not 65536.
This patch removes sclk_cycle_shift from dev_comp, and uses a macro with
a value 20 instead.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds ethernet driver for MediaTek MT7620 SoC.
The MT7620 SoC has a built-in ethernet (Frame Engine) and a built-in
7-port switch and two xMII interfaces (can be MII/RMII/RGMII).
The port 0-3 of the switch connects to intergrited FE PHYs. Port 4 can be
configured to connect to either the intergrited FE PHY, or the xMII.
Port 5 always connects to the xMII. Port 6 is the CPU port.
This driver supports MT7530 giga switch connects to port 5.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds spi controller support for MediaTek MT7620 SoC.
The SPI controller supports two chip selects. These two chip selects are
implemented as two separate register groups, but they share the same bus
(DI/DO/CLK), only CS pins are dedicated for each register group.
Appearently these two register groups cannot operates simulataneously so
they are implemented as one controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds watchdog support for the Mediatek MT7620 SoC
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for MediaTek MT7620 SoC.
The MT7620 SoC supports only pinmux.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7620 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds uart support for MediaTek MT7620 and earlier SoCs.
The UART used by MT7620 is incompatible with the ns16550a driver.
All registers of this UART have different addresses. A special 16-bit
register for Divisor Latch is used to set the baudrate instead of the
original two 8-bit registers (DLL and DLM).
The driver supports of-platdata which is useful for tiny SPL.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In case the clock framework is enabled, enable the SPI controller clock
and obtain max frequency from the clock framework.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
The CSPI/ECSPI register bits do not differ between newer SoCs, instead
of having multiple copies of the same thing for each iMX SoC, define
the bits in the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Add ECSPI clock entries to iMX8MN clock driver. Only make those entries
available in case SPI support in U-Boot is enabled at all to conserve
space, esp. in SPL.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
