Commit graph

622 commits

Author SHA1 Message Date
Tim Harvey
9d41628863 imx: cpu: terminate line with CR if invalid temp sensor
Ensure we terminate the line with a CR if we get an invalid sensor device
or reading.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-11-01 15:52:58 +01:00
Jorge Ramirez-Ortiz
74a039403c mx6: peripheral clock from oscillator
In order to be able to run the I2C bus at 400Khz, the chip errata[1]
recommends that the peripheral clock runs out of the 24MHz oscillator.

Systems running I2C from OP-TEE before Linux executes - for example to
access a Secure Element [2] providing the cryptographic support - expect
this clock to be configured by the bootloader [3].

[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).

Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-11-01 15:52:47 +01:00
Simon Glass
4e28a259fd imx: mx6cuboxi: Disable thermal driver in SPL
This feature is incompatble with of-platdata since it uses the
U_BOOT_DEVICE() macro. With of-platdata the only devices permitted are
those created by dtoc.

The driver is not used in SPL anyway, so exclude it from that build.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-10-29 14:42:56 -06:00
Marek Vasut
d1a7205532 ARM: mx6: ddr: Add support for iMX6UL/ULL/SL/SDL
This patch adds support for iMX6UL/ULL/SL/SDL MMDC into the DDR calibration
code. The difference between MX6DQ and MX6UL/ULL/SL is that the later SoCs
have 2 SDQS registers, just like MX6SX, while the MX6DQ/MX6SDL has 8.

Fixes: 4f4c128c65 ("ARM: mx6: ddr: Add support for iMX6SX")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric@nelint.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-09-17 14:40:55 +02:00
Peng Fan
0098222dac imx8mp: Remove parts MIMX8ML7 and MIMX8ML5 support
Latest datasheet revE has removed MIMX8ML7D/5D/7C/5C parts, so
update u-boot to remove decoding and support for those parts.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-17 14:40:22 +02:00
Peng Fan
a3e7d51fd5 imx8m: clock_imx8mm: add missed return
Add missed return

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-17 14:40:17 +02:00
Peng Fan
27c803848b spl: add g_dnl_get_board_bcd_device_number
Add g_dnl_get_board_bcd_device_number, the new BCD value is used by uuu to distinguish
if the SPL supports the SDPV.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01 14:47:43 +02:00
Tom Rini
f27ffe4177 arm: mx6: Make all i.MX6 SoCs user-selectable
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it.  In some cases, this is handled via board-specific
Kconfig options.  In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS.  This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.

To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support.  This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.

Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2020-08-25 10:26:14 +02:00
Marek Vasut
af50d92ae7 ARM: imx: ddr: Add deskew register programming
Fill is code for programming the DDR_PHY_CMD_DESKEW_CONx registers,
which are optional, but can be used to fill in the byte lane delays.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-08-17 17:55:49 +02:00
Marek Vasut
4b44bea701 ARM: imx: Add support for reading out the primary/secondary bmode to MX7
Implement the 'getprisec' subcommand of 'bmode' command for i.MX7 by
reading out the SRC GPR10 bit 30. This bit is either set by the BootROM
if it switched to the secondary copy due to primary copy being corrupted
OR it can be overridden by the user.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-08-17 17:55:31 +02:00
Marek Vasut
3c0fbbfd95 ARM: imx: Add support for reading out the primary/secondary bmode
Add new 'getprisec' subcommand to 'bmode' command, which sets the return
value of the 'bmode' command to either 0 if the system booted from primary
copy or to 1 if the system booted from secondary copy. This can be used
e.g. in 'test' command to determine which copy of the system is running.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-08-17 17:55:17 +02:00
Marek Vasut
5ec83561c4 ARM: imx: Add support for switching primary/secondary boot mode to bmode
The i.MX6/i.MX7 is capable of booting a secondary "redundant" system
image in case the primary one is corrupted. The user can force this
boot mode as well by explicitly setting SRC GPR10 bit 30. This can be
potentially useful when upgrading the bootloader itself. Expose this
functionality to the user.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-08-17 17:54:01 +02:00
Marek Vasut
c72372d38c ARM: imx: Add bmode support for iMX7
Add the basic differentiation between i.MX6 and i.MX7 into the bmode
command, the mechanism really works almost the same on both platforms.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-08-17 17:53:55 +02:00
Tom Rini
f1c0b7cd4b For 2020.10
-----------
 
 - fixes for Toradex board
 - fix warnings from previous PR
 - HAB: reset instead of panic after failure
 - new board:  MYiR Tech MYS-6ULX
 - mx6cuboxi: use OF_PLATDATA
 - further changes for DM
 
 Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
 4hKj5yxRg3cvb/pBAmbQ
 =TyRs
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

For 2020.10
-----------

- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board:  MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM

Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
2020-08-04 11:11:02 -04:00
Simon Glass
055efe5690 thermal: Drop dm.h header file
This header file should not be included in other header files. Remove it
and use a forward declaration instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-08-03 22:19:54 -04:00
Marek Vasut
1e7a69f661 ARM: imx: hab: panic on authentication failure
Instead of hang()ing the system and thus disallowing any automated
recovery possibility from a HAB authentication failure, panic() .
The panic() function can be configured to hang() the system after
printing an error message, however the default is to reset the
system instead.

This allows redundant boot to work correctly. In case the primary
or secondary image cannot be authenticated, the system reboots and
bootrom can try to start the other one.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-08-03 17:03:57 +02:00
Parthiban Nallathambi
10e959a1ca imx: Add MYiR Tech MYS-6ULX support
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.

CPU:   Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM:  256 MiB
NAND:  256 MiB
MMC:   FSL_SDHC: 0
In:    serial@2020000
Out:   serial@2020000
Err:   serial@2020000
Net:   FEC0

Working:
 - Eth0
 - MMC/SD
 - NAND
 - UART 1
 - USB host

Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
2020-08-03 17:03:57 +02:00
Fabio Estevam
68a699e1e8 imx8m: soc: Remove unneeded space
Checkpatch reports the following issue:

ERROR: space prohibited before that ',' (ctx:WxW)
#936: FILE: arch/arm/mach-imx/imx8m/soc.c:936:
+		      0, 0 , 0, 0, 0, 0, &res);

Remove the unneeded space.
 		           ^
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-07-27 14:02:37 +02:00
Igor Opaniuk
fb99ac9caf imx: mx7: fix DDRC size in A7-M4 mapping table
According to i.MX 7Solo Applications Processor Reference Manual,
2.1.3 Cortex-M4 Memory Map, M4 can address only 1536MB of DDRC
(Start Address: 0x8000_0000; End Address: 0xDFFF_FFFF).
Correct DDRC size to 0x60000000.

Fixes: c0f037f6("mach-imx: bootaux: elf firmware support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-27 14:00:36 +02:00
Masahiro Yamada
b75d8dc564 treewide: convert bd_t to struct bd_info by coccinelle
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>

  #include <asm/u-boot.h>
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  <smpl>
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  </smpl>

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-07-17 09:30:13 -04:00
Heinrich Schuchardt
90865614b4 ARM: mx6: make CAAM usable on the i.MX6 boards
Even if the HAB fuse is not set we want to be able to use the Cryptographic
Accelerator and Assurance Module (CAAM) for generating random numbers. So
SYS_FSL_HAS_SEC should be selected even if IMX_HAB is not set.

arch_misc_init() has to be called to initialize the CAAM.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-07-16 11:20:08 +02:00
Niel Fourie
26a6ed1b2e arm: imx6q: pcm058: Convert pcm058 to use DM with DTs
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.

Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2020-07-14 11:46:04 +02:00
Peng Fan
eb3967388e imx8m: implement armv8_el2_to_aarch32
Add iMX8M specific armv8_el2_to_aarch32 to let AArch64 mode U-Boot
could boot aarch32 mode linux with FIT image as below:

/dts-v1/;

/ {
        description = "Configuration to load ARM32 Linux";

        images {
                kernel@1 {
                        description = "ARM32 Linux kernel";
                        data = /incbin/("./Image");
                        type = "kernel";
                        arch = "arm";
                        os = "linux";
                        compression = "none";
                        load = <0x40008000>;
                        entry = <0x40008000>;
                        hash@1 {
                                algo = "md5";
                        };
                };
                fdt@1 {
                        description = "Flattened Device Tree blob";
                        data = /incbin/("./imx8mm-evk.dtb");
                        type = "flat_dt";
                        arch = "arm";
                        compression = "none";
                        load = <0x43000000>;
                        hash@1 {
                                algo = "md5";
                        };
                };
        };
        configurations {
                default = "config@1";

                config@1 {
                        description = "fsl-imx8mm-evk";
                        kernel = "kernel@1";
                        fdt = "fdt@1";
                };
        };
};

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:48 +08:00
Peng Fan
3c41728d80 imx8m: Refactor the OPTEE memory removal
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.

When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:48 +08:00
Peng Fan
6036dba1c8 imx8m: disable nodes before kernel/mfgtool boot for fused part
To fused part, we need to disable nodes of dtb to let kernel boot.

To mfgtool, USB issue when using super-speed for mfgtool, temporally
work around the problem to use high-speed only.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Ye Li
2707faf01f imx8mn/imx8mp: override env_get_offset and env_get_location
To use one defconfig for all boot device, we have to runtime set
env offset and return env medium according to the boot device.
This patch overrides the env_get_offset and env_get_location to
implement the feature.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
7a42bf0489 imx8m: power down fused cores
For non-Quad SoCs, the fused cpu cores could be powered down in SPL
to save power.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Ye Li
d1eee7eed9 imx8mp: Add fused parts support
iMX8MP has 6 fused parts in each qualification tier, with core, VPU,
ISP, NPU or DSP fused respectively.

The configuration tables for enabled modules:
MIMX8ML8DVNLZAA          Quad Core, VPU, NPU, ISP, DSP
MIMX8ML7DVNLZAA          Quad Core, NPU, ISP
MIMX8ML6DVNLZAA          Quad Core, VPU, ISP
MIMX8ML5DVNLZAA          Quad Core, VPU
MIMX8ML4DVNLZAA          Quad Lite
MIMX8ML3DVNLZAA          Dual Core, VPU, NPU, ISP, DSP

Add the support in U-Boot

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
2f3c92060d imx8m: workaround ROM serror
ROM SError happens on two cases:

1. ERR050342, on iMX8MQ HDCP enabled parts ROM writes to GPV1 register, but
when ROM patch lock is fused, this write will cause SError.

2. ERR050350, on iMX8MQ/MM/MN, when the field return fuse is burned, HAB
is field return mode, but the last 4K of ROM is still protected and cause
SError.

Since ROM mask SError until ATF unmask it, so then ATF always meets the
exception. This patch works around the issue in SPL by enabling SPL
Exception vectors table and the SError exception, take the exception
to eret immediately to clear the SError.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
3c9221ad27 imx8m: add eqos clk
Add imx_eqos_txclk_set_rate/imx_get_eqos_csr_clk to override the
weak function in driver

Add set_clk_eqos to configure eQoS clk

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
3c1c28d4e0 imx8m: add sdhc/nand/ecspi clk api
Current DM CLK is a bit complicated, for simplity, let DM clk only
support enable/disable/get_rate. For the expected rate settings,
we use non-DM clk to do that. Then we could have simple DM clk for
i.MX and could also share between SPL/U-Boot proper.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
14254e646d imx8m: configure NoC clk
Configure NoC clk for better system performance

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
46a8a28bf6 imx8m: configure arm clk sources from PLL
A53 CCM root max support 1GHz, to support high freq, we need
to switch ARM clk sources from ARM PLL directly.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
d6498bc459 imx: remove imx sip file
We have switch to use arm_smccc_smc, no need to keep i.MX specific
sip wrapper.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:47 +08:00
Peng Fan
bf26b9421e imx: bootaux: use arm_smccc_smc
Use arm_smccc_smc to replace call_imx_sip

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Peng Fan
a2f143eaac imx8m: soc: use arm_smccc_smc
Use arm_smccc_smc to replace call_imx_sip

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Peng Fan
dc575201c8 imx8: misc: use arm_smccc_smc
Use arm_smccc_smc to replace call_imx_sip

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:46 +08:00
Jagan Teki
f247354708 arm: Remove mx31pdk board
DM, OF_CONTROL, DM_SPI and other driver model migration
deadlines are expired for this board.

Remove it.

Acked-by: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2020-07-09 20:58:06 +05:30
Tom Rini
7d80a9cd92 arm: imx: Finish migration of CONFIG_CSF_SIZE to Kconfig
While in most cases CSF_SIZE is handled via Kconfig we have some i.MX8M
platforms that set the size based on the now-renamed CONFIG_SECURE_BOOT
symbol.  Update things so that CSF_SIZE itself depends on IMX_HAB being
enabled and provide the default value for i.MX8M family of parts.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Ye Li <ye.li@nxp.com>
2020-06-26 10:29:06 -04:00
Tom Rini
0567099bea arm: imx: Finish migration from CONFIG_SECURE_BOOT to CONFIG_IMX_HAB
There are a few remaining places where we say CONFIG_SECURE_BOOT rather
than CONFIG_IMX HAB.  Update these instances.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Fixes: d714a75fd4 ("imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-06-26 10:29:06 -04:00
Marek Vasut
a1f6d04aa1 ARM: imx: soc: Select default TEXT_BASE for MX7
Select default U-Boot and SPL text base for the MX7 SoC. The U-Boot
text base is picked as the one used by various MX7 boards. The SPL
text base however is different.

The SPL text base is set to 0x912000 instead of the usual 0x911000,
that is because the 0x911000 value cannot work. Using 0x911000 as a
SPL text base will result in the DCD header being placed below the
0x911000 address, which is a reserved SRAM area which must not be
used. This will actually trigger eMMC boot failure on MX7D at least.
Hence the increment.

Update all boards affected by this SPL problem to the new SPL_TEXT_BASE.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-06-22 17:44:20 +02:00
Marek Vasut
cb82ee25f7 ARM: imx: ddr: Fill in missing DDRC ZQCTLx on i.MX7
The iMX7 defines further DDRC ZQCTLx registers, however those were
thus far missing from the list of registers and not programmed. On
systems with LPDDR2 or DDR3, those registers must be programmed with
correct values, otherwise the DRAM may not work. However, existing
systems which worked without programming these registers before are
now setting those registers to 0, which is the default value, so no
functional change there.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-06-22 17:44:06 +02:00
Stefano Babic
3854296801 Revert "imx: rom api: fix image offset computation"
This reverts commit 1f63ee6566.

As reported by Ye Li on ML:

1. Removing the image_offset will break secondary (redundant) boot support for sd and emmc.
2. When booting from emmc boot partition, the image_offset is 0. But the flash.bin
generated by mkimage with imximage-8mp-lpddr4.cfg is for sd. It expects to be burn at 32KB offset.
The fit offset 0x60000 has already included the 32KB offset.  So when you burn this flash.bin
to emmc boot partition at offset 0, the fit offset should subtract the 32KB (0x60000 - 0x8000).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2020-06-09 11:19:55 +02:00
Marek Vasut
0e06d63d19 ARM: imx: ddr: Add missing PHY reset
The iMX7D RM 9.2.4.9.3 Power removal flow Table 9-11. Re-enabling power
explicitly says both the DDR controller and the PHY must be reset in the
correct sequence. Currently the code only resets the controller. This
leads to a misbehavior where the system brings the DRAM up after reboot,
but the DRAM is unstable. Add the missing reset.

The easiest way to trigger this is by triggering WDT without having the
WDT assert WDOG_B signal, i.e. mw.w 0x30280000 0x25 .

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-06-08 10:42:54 +02:00
Sébastien Szymanski
1f63ee6566 imx: rom api: fix image offset computation
When not booting from FlexSPI, the offset computation is:

offset = image_offset + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000;

When booting from SD card or eMMC user partition, image_offset is
0x8000. It is useless to add and remove 0x8000.
When booting from other device, image_offset is 0 so this computation is wrong.

Simplfy this computation to work on all booting devices.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2020-06-08 10:42:14 +02:00
Patrick Wildt
0e9c045b2b imx: move ATF to the back of the FIT to fix loading over yModem
With yModem the FIT Image is only supplied once, so we can only
seek forward in the yModem supplied image and never backwards.
With the recent changes to the SPL mechanism, including loading
U-Boot first, FDT after, then the loadables, we must also reorder
the FIT image script to make sure that the loadables are last in
the FIT image.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2020-06-08 10:41:38 +02:00
Peng Fan
f3e1c536a9 imx: Kconfig: enable IMX_BOOTAUX for i.MX8M
i.MX8M could use imx bootaux to boot m4/m7 core, so let's add it
to the dependency list.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-06-08 10:39:24 +02:00
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c05ed00afb common: Drop linux/delay.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
eb41d8a1be common: Drop linux/bug.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
25a5818ff8 common: Drop asm/ptrace.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Simon Glass
0914011310 command: Remove the cmd_tbl_t typedef
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 18:36:55 -04:00
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
4d72caa5b9 common: Drop image.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Simon Glass
c3dc39a2f8 arm: Don't include common.h in header files
It is bad practice to include common.h in other header files since it can
bring in any number of superfluous definitions. It implies that some C
files don't include it and thus may be missing CONFIG options that are set
up by that file. The C files should include these themselves.

Update some header files in arch/arm to drop this.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 14:54:24 -04:00
Peng Fan
d52a03b130 imx8: cpu: check resource owned after sid fail
When we create software partition, we still need let parent
partition to configure sid, so move the check after sid failed.

Acked-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:21 +02:00
Peng Fan
ed5b253d0e imx: imx8qm/qxp: check whether m4 partition booted
Add code to check m4 partition booted or not, we will use this
to runtime set device tree file that passed to Linux Kernel.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
42b26ddc80 imx8: Select boot device dynamically
For fspi build, we will enable both SPL NOR support and SPL SPI
support. SPL will dynamically check the resource owner then
select corresponding boot device.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
6aead23323 imx: imx8qm/qxp: Recover SPL data section for partition reboot
When doing partition reboot, the boot image won't be reloaded by ROM,
it is just CPU reset to boot entry. The SW has to keep the boot image
inside the RAM unchanged. It includes both the TEXT section and DATA
section.

For SPL, the problem is DATA section will be updated at runtime, so in
next partition reboot the data is not same as the initial value from
cold boot. If any code depends on the initial value, then it will have
problem.

This patch introduces a mechanism to recover the data section
for partition reboot. It adds a new section in image for saving
data section. When from cold boot, the data section will be saved
to that new section at SPL early phase. When from partition reboot,
the data section will be restored from the new section.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
8103767256 imx: imx8qm/qxp: add get_board_serial
Add get_board_serial support, the info could be got from fuse.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
7c351ff5e0 imx: imx8qm/qxp: Fix issue in get_effective_memsize
When Trusty OS allocates the mem region from 0xfe0000000-0xffffffff,
the get_effective_memsize does not return correct memory size.
There is a check in get_effective_memsize to find the memreg where
the u-boot is running, and return the size of that memreg as the result
of get_effective_memsize. When using aligned start, the value is
0x80200000 since it is 2MB aligned. Thus the finding of memreg will
fail and return the PHYS_SDRAM_1_SIZE because u-boot text base is
0x80020000. This cause u-boot is relocated to the high memory where has
been occupied by Trusty OS.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
f44afd546f imx: imx8qm/qxp: reserving DDR memory for M4
The DDR memory from 0x88000000 to 0x8FFFFFFF is assigned to M4 on
QM and QXP. The M4 can allocate this memory by two ways,
in SCD or u-boot.

In this patch, u-boot addes the memory reserve node to DTB to pass
the info to kernel, no matter the M4 memory is reserved in SCD
or u-boot. So kernel won't access M4 reserved memory.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
f797fe84fc nandbcb: read boot search count from fuse for imx8qxp
add support for imx8qxp to read boot search count from fuse in nandbcb

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
214b7d534d cmd: nandbcb: Reconstruct the nandbcb tool for all platforms
The original nandbcb tool was designed for imx6 only, when trying to
leverage it to replace the kobs-ng tool, we found the design is not
friendly for supporting all platforms. To support all iMX6/7/8 platforms
and for easy further maintain, I reconstruct the structure of the tool.

The main changes including:

1. Use platform_data to determine the logic branches rather than simply
   use SOC name.
2. More data structures as parameter for functions.
3. Global variables to define the FCB/DBBT/FW locations.
4. Implement the kobs-ng default 4 FCB/4 DBBT/2 FW layout.
5. Support Hamming coding/ 40bit BCH/ 62bit BCH coding FCB.
6. Dump and compare all written FCB/DBBT to verify data integrity.

The tool has been verified on iMX6Q/DL, 6SX, 7D, 6ULL, iMX8QX, iMX8MM.

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Alice Guo
49f8454705 nandbcb: add nandbcb dump command for i.MX6
Verify/dump boot structures.

Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Alice Guo
0b10337b21 nandbcb: add nandbcb dump command for i.MX8MM
Verify/dump boot structures written to NAND Flash chip.

Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Alice Guo
66dbd9c9ed nandbcb: support i.MX8M
Tested on i.MX8MM EVK, imx8mm evk uses BCH
encoding and randomizer
modify macro and print size_t with %zx
use CONFIG_IMX8M because it should apply to imx8mq/mm/mn

Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Han Xu
c6ed3508bd nandbcb: fix the issue cannot support gf_14 NAND boot
bchtype in FCB should be associated to the gf_13/14 settings in BCH, fix
the issue and test on Micron 29F64G08CBABB, it can boot after the
change.

Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Leonard Crestez
6fcb2ee783 imx8: Replace SC_R_LAST with SC_R_NONE in DTB
We are currently using SC_R_LAST as a marker for imx8 power domain tree
nodes without a resource attached. This value is compiled into dtb as
part of the linux build and used by uboot.

The SC_R_LAST constant changes frequently as SCFW resources are added
(by design) and every time we need to update linux and uboot headers
together or boot can fail.

Fix this by replacing SC_R_LAST usage with a new constant SC_R_NONE
defined to be 0xFFF0.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Adam Ford
f36f8bc627 imx: Add support for i.MX8MM Beacon EmbeddedWorks devkit.
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.

It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.

Signed-off-by: Adam Ford <aford173@gmail.com>
2020-05-10 20:55:20 +02:00
Peng Fan
dc597d1d40 imx: cpu: support tmu
Support tmu when print cpu info

Signed-off-by: peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
3462b55d17 imx8mp: Set default SNSR25C for TMU probe1
So far u-boot only load SNSR25C for TMU main probe (probe 0). However,
kernel enables two probes. So it also needs to set default SNSR25C of
TCALIV1 for blank samples.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
ebb9aab318 imx: load calibration parameters from fuse for i.MX8MP
i.MX8MP thermal which has two probes and supports temperature range
from -40 to 125.  The driver still uses default 1p HW
calibration at 25C and loads calibration parameters from fuse.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
94c693d782 imx: i.MX8MN: Enable loading TASR and TCALIV from fuse
Like iMX8MM, iMX8MN also needs SW to load TMU TASR and TCALIV registers
value from fuse before enabling TMU calibration. Otherwise the calibration
is not exact.

Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Ye Li
70487ff386 imx8mm: Load fuse for TMU TCALIV and TASR
On iMX8MM, the default value of TMU registers TCALIV and TASR need
be loaded from fuse. HW won't do this, it expect SW loads them before
using TMU.

Reviewed-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
3c42c0f673 imx: add module fuse support
There are different parts from one SoC. Take i.MX6ULL for example,
some part might not have ENET, some might have; some might not have
USB, some might have. The information could be got from OCOTP,
to make one image support the different parts, we need runtime
disable linux kernel dts node and uboot driver probe if the
corresponding module not exists in the part.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 13:21:13 +02:00
Marek Vasut
b52fb0b0b5 ARM: imx: pico-imx8mq: Add support for Technexion Pico-iMX8MQ
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-05-10 13:19:39 +02:00
Harald Seiler
d81a68957f imx: spl: Fix use of removed SPL_FAT_SUPPORT config
CONFIG_SPL_FAT_SUPPORT was removed in commit 0c3a9ed409
("spl: Kconfig: Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT").
Fixup a leftover use of the symbol.

Fixes: 9d86dbd9cf ("imx: spl: implement spl_boot_mode for i.MX7/8/8M")
Signed-off-by: Harald Seiler <hws@denx.de>
2020-05-01 18:48:48 +02:00
Harald Seiler
5fc5bac67b imx: spl: Remove ifdefs in spl_mmc_boot_mode()
It is hard to read code which contains nested ifdef blocks.  Replace
them with normal if-blocks and the IS_ENABLED() macro.  This is not only
more readable but also helps as both arms are validated by the compiler
in all cases.

Signed-off-by: Harald Seiler <hws@denx.de>
2020-05-01 18:48:36 +02:00
Harald Seiler
15aec318ef Revert "imx: Introduce CONFIG_SPL_FORCE_MMC_BOOT to force MMC boot on falcon mode"
The CONFIG_SPL_FORCE_MMC_BOOT config flag is not needed as its behavior
is the correct one in all cases;  using spl_boot_device() instead of the
boot_device parameter will lead to inconsistency issues, for example,
when a board_boot_order() is defined.  In fact, this is the reason the
parameter was introduced in the first place, in commit 2b1cdafa9f
("common: Pass the boot device into spl_boot_mode()").

This reverts commit 772b55723b.

Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
2020-05-01 18:47:07 +02:00
Anatolij Gustschin
a15d0aa680 imx: spl: return boot mode for asked MMC device in spl_mmc_boot_mode()
Boards may extend or re-define the boot list in their board_boot_order()
function by modifying spl_boot_list. E.g. a board might boot SPL from a
slow SPI NOR flash and then load the U-Boot from an eMMC or SD-card.
Or it might use additional MMC boot device in spl_boot_list for cases
when the image in SPI NOR flash is not found, so it could fall back to
eMMC, SD-card or another boot device.

Getting the MMC boot mode in spl_mmc will fail when we are trying to
boot from an MMC device in the spl_boot_list and the original board
boot mode (as returned by spl_boot_device()) is not an MMC boot mode.
Fix it by checking the asked MMC boot device from the spl_mmc_boot_mode()
argument.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-05-01 18:46:55 +02:00
Alifer Moraes
ef99f3d9e8 arm: imx: Add support for Google's Coral Dev Board
Add initial support for Google's Coral Dev Board based on i.MX8MQ.

https://coral.ai/products/dev-board

The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:

https://coral.googlesource.com/uboot-imx/

Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
2020-05-01 13:49:15 +02:00
Claudius Heine
c5635a032a ARM: imx8m: Don't use the addr parameter of reset_cpu()
imx8m has the only implementation of reset_cpu() which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers.  This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.

Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-developed-by: Harald Seiler <hws@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
2020-05-01 13:46:22 +02:00
Harald Seiler
568af92679 ARM: imx8m: Fix indentation of reset_cpu() function
Use proper code-style, tabs instead of spaces for indentation.

Signed-off-by: Harald Seiler <hws@denx.de>
2020-05-01 13:46:22 +02:00
Marek Vasut
efa1a62ad2 ARM: imx8m: Do not define do_reset() if sysreset is enabled
The SPL can also be compiled with sysreset drivers just fine, so
update the condition to cater for that option.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-05-01 13:46:22 +02:00
Marek Vasut
dabaabd3f1 ARM: imx: imx8m: Do not warn about cpu-idle-states if missing
If the cpu-idle-states is missing from the DT in the first place, do
not fail on removing in. Just move on and do not even print an error,
since not being able to remove something which is not there in the
first place is not an error and surely does not justify failing to
boot.

Turn the surrounding prints into debugs to reduce the useless noise.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2020-05-01 13:46:22 +02:00
Claudius Heine
3675d93875 imx: imx8m: Don't use the addr parameter of reset_cpu
imx8m has the only implementation of `reset_cpu` which does not ignore
the addr parameter and instead gives it some meaning as the base address
of watchdog registers.  This breaks convention with the rest of U-Boot
where the parameter is ignored and callers are passing in 0.

Fixes: d2041725e8 ("imx8m: restrict reset_cpu")
Co-Authored-by: Harald Seiler <hws@denx.de>
Signed-off-by: Claudius Heine <ch@denx.de>
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
2020-05-01 13:46:22 +02:00
Franck LENORMAND
242d1cd69b imx8: Configure SNVS
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.

The module also adds some commands:
 - snvs_cfg: Configure the SNVS HP and LP registers
 - snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
 - tamper_pin_cfg: Change the configuration of the tamper pins
 - snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
   status bits

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Ye Li
7247974643 imx8m: Enable WDOG_B for timeout
When doing reset_cpu, in normal case the WDOG_B outputs immediately
after we clean WDA bit. But on mscale, the WDOG_B may be later than
internal reset, and cause PMIC not reset. As we enabled the SD3.0
support, the PMIC must be reset to reset SD card.

Change the reset_cpu to enable the WDOG_B for timeout as well, and set
WDOG timeout to 1s.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Ye Li
1c97fcda7f imx8mm: clock: fix fracpll decode issue
The fracpll decoding is using the bit definitions for int pll. Most of
them are same, but the CLKE bit is different. Fix the wrong CLKE_MASK
for fracpll and correct all bit definitions in fracpll decoding.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Peng Fan
828ad358a5 imx8: parser: fix some bad debug message formating
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.

Modified from Seb Fagard's downstream patch

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Seb Fagard
0e248b5f02 imx8: ahab: fix some bad debug message formating
In SPL build, the formatting '%llx' in debug() is not supported.
Also, fix some misplaced parameters in printf.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Seb Fagard <sebastien.fagard@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Peng Fan
abf7752c40 imx8: ahab: fix 'end address' parameter of rm_find_memreg
parameter 'end address' must be inclusive of address range.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:21 +02:00
Ye Li
a903e13f97 imx8: Change to use new SECO API commands
Latest SCFW has removed old MISC SECO commands. So update the codes
to use new SECO commands.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:21 +02:00
Peng Fan
b7328de6cd imx8: parser: fix 'end address' parameter of rm_find_memreg
parameter 'end address' must be inclusive of address range.

Modified from Seb's downstream patch.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:21 +02:00
Ye Li
6fcd0b2388 imx8m: Dump DRAM PLL rate by clocks command
Add the dump of DRAM PLL into "clocks" command

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
2020-05-01 13:46:21 +02:00
Peng Fan
712a341c76 imx8mq: Set ARM core clock directly from ARM PLL
For ARM core clock, there are two input branches, and can select via mux:
one from ARM PLL directly, second from CCM A53 clock root.

Currently we are using second branch. But IC confirmed the CCM A53 root
signoff timing is 1Ghz, so we should switch to input from ARM PLL directly.

This patch fixes the CORE SEL slice configuration and switch ARM clock
to ARM PLL.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:21 +02:00
Ye Li
15a7426045 imx8mq: Enable eMMC HS400 and SD UHS mode on EVK
iMX8MQ EVK board has a eMMC5.0 chip and supports SD3.0, so enable the UHS
and HS400 configs to enhance the eMMC/SD access.

The change also needs to set usdhc clock to 400Mhz, and add the
off-on-delay-us to SD reset pin, otherwise some SD cards will
fail to select UHS mode in re-initialization.

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:21 +02:00