Commit graph

10 commits

Author SHA1 Message Date
Peng Fan
6d5cc90670 imx: imx8mn_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Gaurav Jain
ee51b2c767 i.MX8M: crypto: updated device tree for supporting DM in SPL
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
2022-04-12 11:18:34 +02:00
Andrey Zhizhikin
94588ff395 imx8mn-ddr4-evk: generate single bootable image
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.

Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.

Update documentation to drop additional step of copying u-boot.itb

Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-02-05 15:49:01 +01:00
Peng Fan
353dfe4b43 imx8mn-ddr4-evk: switch to use binman
Use binman to pack images

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:53 +02:00
Clement Faure
56d2050f40 imx8m: Add DEK blob encapsulation for imx8m
Add DEK blob encapsulation support for IMX8M through "dek_blob" command.
On ARMv8, u-boot runs in non-secure, thus cannot encapsulate a DEK blob
for encrypted boot.
The DEK blob is encapsulated by OP-TEE through a trusted application call.
U-boot sends and receives the DEK and the DEK blob binaries through OP-TEE
dynamic shared memory.

To enable the DEK blob encapsulation, add to the defconfig:
CONFIG_SECURE_BOOT=y
CONFIG_FAT_WRITE=y
CONFIG_CMD_DEKBLOB=y

Signed-off-by: Clement Faure <clement.faure@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 20:29:52 +02:00
Peng Fan
4e805c197b imx8mn: Add LPDDR4 EVK board support
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-04-08 09:18:29 +02:00
Andrey Zhizhikin
50b1a69cee ARM: dts: imx8m: add UHS or HS400/HS400ES properties
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.

Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
2020-12-26 12:36:35 +01:00
Andrey Zhizhikin
247bbeb74c ARM: dts: imx8m: increase off-on delay on the SD Vcc regulator
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.

Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.

Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.

Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-12-26 12:36:19 +01:00
Marek Vasut
2455f91833 ARM: imx8m: Fix reset in SPL on NXP iMX8MN EVK
Board files should not re-implement do_reset() to work around this
function not being defined in for specific configurations. Rather,
the fix is to compile in drivers which implement this properly.
This patch enables sysreset and watchdog drivers in SPL and ties
them together to implement the same as the do_reset() hack in the
board file, except correctly in the DM/DT framework.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Flavio Suligoi <f.suligoi@asem.it>
Cc: Harald Seiler <hws@denx.de>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2020-05-01 13:46:22 +02:00
Peng Fan
d239d9d946 imx: add i.MX8MN DDR4 board support
Support pinctrl/clk/sdhc, include ddr4 timing data.

Log:
U-Boot SPL 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)
Normal Boot
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2019.10-rc3-00356-g497c500423-dirty (Sep 16 2019 - 10:54:58 +0800)

CPU:   Freescale i.MX8MNano rev1.0 at 24 MHz
Reset cause: POR
Model: NXP i.MX8MNano DDR4 EVK board
DRAM:  2 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-05 10:27:18 +01:00