Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC,
but uses Cortex-A53 cores instead.
So move the shared cpu based and peripherals nodes into
sun50i-h5.dtsi so, that it can shared among the sun50i-h5
board dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Linux device tree for the Allwinner A64 SoC has changed a lot since
the U-Boot version was merged.
Let's replace the current DT with a exact copy of the Linux one as of:
commit c6778ff813d2ca3e3c8733c87dc8b6831a64578b
Merge: 0ff4c01 3c0e3abd
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Tue May 9 10:07:33 2017 -0700
This is the DT used in Linux 4.12-rc1.
Since U-Boot has an Ethernet driver (while Linux does not yet), we
provide the required DT nodes for it in an ...-u-boot.dtsi file, to both
mark them as U-Boot specific and to allow easier upgrading once Linux gets
the driver and its own binding later.
Compared to the existing Ethernet DT nodes we just slightly tweak the clock
and reset nodes in there to match the new bindings used by Linux for those.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Update the NanoPi Neo device tree file to use the NanoPi dtsi.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.
Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The pwm3 on evb-rk3399 is used for pwm regulator, need to invert
the polarity to make it work correctly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
The DDR3-1333 timings for the RK3399-Q7 (Puma) has some unintended
left-over comments in them. This change cleans the file up.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
Previous commit has this combined with SOM-LV. This commit has only
the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes
will be submitted to the linux-omap list
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split device tree from other board
This adds the device tree. Previous commit added both boards at the
same time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split the SOM-LV from Torpedo
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus.
This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related
device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This is needed to probe devices under that bus such as the SATA PHY.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
- Fix the build error for the usb0 node.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Add the clk pinctrl of the mmc0 node.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
