The patch adds helper funtions for basic access to the registers
of the MC9sdz60 chip (multifunctional device with RTC and CAN) via
I2C interface.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The actual SPI driver for i.MX31 and i.MX51 controller
use a wrong byte ordering, because it is supposed
to work only with Freescale's devices, as the Power
Controllers (PMIC). The driver is not suitable for
general purposes, because the buffers passed to spi_xfer
must be 32-bit aligned, as it is used mainly to send
integer to PMIC devices.
The patch drops any kind of limitation and makes the
driver useful with devices controlled sending commands
composed by single bytes (or by a odd number of bytes), such as
spi flash, sensor, etc.
Because the byte ordering is changed,
any current driver using this controller must be adapted, too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add printing of LAWBARH/LAWBARL for FSL_CORENET platforms.
Signed-off-by: Becky Bruce <Beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current code redefines functions based on FSL_CORENET_ vs not -
create macros/inlines instead that hide the differences.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds the gpio usage request. The polarity is changed to
positive as suggested by Mike Frysinger.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch adds a status led driver followed the GPIO access
conventions of Linux. The led mask is used to specify the gpio pin.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).
Signed-off-by: Stefano Babic <sbabic@denx.de>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added P1012/P1013/P1021/P1022 to cpu_type_list and SVR list
* Added number of LAWs for P1012/P1013/P1021/P1022
* Set CONFIG_MAX_CPUS to 2 for P1021/P1022
* PCI port config
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p4080 & p4040 to cpu_type_list and SVR list
* Added number of LAWs for p4080
* Set CONFIG_MAX_CPUS to 8 for p4080
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet based platforms the LAW address is split between an high &
low register and we no longer shift the address. Also, the target IDs
on CoreNet platforms have been completely re-assigned.
Additionally, added a new find_law() API to which LAW an address hits in.
This is need for the CoreNet style boot release code since it will need
to determine what the target ID should be set to for boot window
translation.
Finally, enamed LAWAR_EN to LAW_EN and moved to header so we can use
it elsewhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536E is capable of booting form NAND/eSDHC/eSPI, this patch
implements these three bootup methods in a unified way - all of these
use the general cpu/mpc85xx/start.S, and load the main image to L2SRAM
which lets us use the SPD to initialize the SDRAM.
For all three bootup methods, the bootup process can be divided into two
stages: the first stage will initialize the corresponding controller,
configure the L2SRAM, then copy the second stage image to L2SRAM and
jump to it. The second stage image is just like the general U-Boot image
to configure all the hardware and boot up to U-Boot command line.
When boot from NAND, the eLBC controller will first load the first stage
image to internal 4K RAM buffer because it's also stored on the NAND
flash. The first stage image, also call 4K NAND loader, will initialize
the L2SRAM, load the second stage image to L2SRAM and jump to it. The 4K
NAND loader's code comes from the corresponding nand_spl directory, along
with the code twisted by CONFIG_NAND_SPL.
When boot from eSDHC/eSPI, there's no such a first stage image because
the CPU ROM code does the same work. It will initialize the L2SRAM
according to the config addr/word pairs on the fixed address and
initialize the eSDHC/eSPI controller, then load the second stage image
to L2SRAM and jump to it.
The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the
second stage image for all different bootup methods. It's set in the
board config file when one of the bootup methods above is selected.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After programming a new LAW, we should read-back the LAWAR register so that
we sync the writes. Otherwise, code that attempts to use the new LAW-mapped
memory might fail right away.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1011 - Single core variant of P1020
P2010 - Single core variant of P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of QorIQ series of processors which falls in ULE
category. It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities.
Also the SOC is pin compatible with P2020
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Many of the help messages were not really helpful; for example, many
commands that take no arguments would not print a correct synopsis
line, but "No additional help available." which is not exactly wrong,
but not helpful either.
Commit ``Make "usage" messages more helpful.'' changed this
partially. But it also became clear that lots of "Usage" and "Help"
messages (fields "usage" and "help" in struct cmd_tbl_s respective)
were actually redundant.
This patch cleans this up - for example:
Before:
=> help dtt
dtt - Digital Thermometer and Thermostat
Usage:
dtt - Read temperature from digital thermometer and thermostat.
After:
=> help dtt
dtt - Read temperature from Digital Thermometer and Thermostat
Usage:
dtt
Signed-off-by: Wolfgang Denk <wd@denx.de>
In set_ddr_laws() when we determined how much of the size requested
to be mapped was covered by the the first LAW we needed to recalculate
the size based on what was actually mapped.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a workaround for MPC8569 CPU Errata, which needs to set Bit 13 of
LBCR in 4K bootpage. We setup a temp TLB for eLBC controller in bootpage,
then invalidate it after LBCR bit 13 is set.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added various p2020 processor specific details:
* SVR for p2020, p2020E
* immap updates for LAWs and DDR on p2020
* LAW defines related to p2020
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Initial support for the DS4510, a CPU supervisor with
integrated EEPROM, SRAM, and 4 programmable non-volatile
GPIO pins. The CONFIG_DS4510 define enables support
for the device while the CONFIG_CMD_DS4510 define
enables the ds4510 command. The additional
CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and
CONFIG_DS4510_RST defines add additional sub-commands
to the ds4510 command when defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Debug sessions may have left enabled laws.
Changing lawbar with an unkown enabled tgtid could cause problems.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
The MPC8536 Adds SDHC and SATA controllers to the PQ3 family. We
also have SERDES init code for the 8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Provide a helper function that will setup the last available
LAWs (upto 2) for DDR. Useful for SPD/dyanmic DDR setting code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
LAWs have the concept of priority so its useful to be able to allocate
the lowest (highest number) priority. We will end up using this with the
new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.
In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.
Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Move the initialization of the LAWs into C code and provide an API
to allow modification of LAWs after init.
Board code is responsible to provide a law_table and num_law_entries.
We should be able to use the same code on 86xx as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
