* fixes the bug in function bind_drivers_pass that for
CONFIG_CC_OPTIMIZE_FOR_SIZE=n and no entries in the driver_info list,
i.e. n_ents == 0, the processor steps into the first loop iteration
despite the loop condition being false.
* the Xilinx Zynq-7000 device would eventually hang due to an attempted
access to an invalid memory address
* the bug is fixed by changing the type of idx from uint to int
Board: zynq-zybo
Target: ARM
Compiler: arm-none-eabi-gcc 9.2.1
Signed-off-by: Alexander Preissner <fpga-garage@preissner-muc.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Enable saving environment to SPI flash memory on SiFive
Unmatched.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Configure SPI flash devices into SPL. Add SPI boot option to spl.c.
Document how to format flash for booting.
Signed-off-by: Thomas Skibo <thomas-git@skibo.net>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
UART1 use for U-Boot and Linux console instead of UART0 and
UART0 is reserved for Hart Software Services(HSS).
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch updates Microchip MPFS Icicle Kit support. For now,
add Microchip I2C driver, set environment variables for
mac addresses and default build for SBI_V02.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The device tree split into .dtsi and .dts files, common
device node for eMMC/SD, enable I2C1, UART1 for console
instead of UART0, enable the DDR 2GB memory and in
that 288MB memory is reserved for fabric buffer.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add I2C driver code for the Microchip PolarFire SoC.
This driver supports I2C data transfer and probe for I2C
slave addresses.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove the microchip compatible string and default compatible "cdns,macb"
support both 32-bit and 64-bit DMA access.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add boot command "bootcmd_ram" to support autoboot from RAM.
This feature could be useful at the very initial state of chip design
when there is only a minimal set of peripheral. (e.g. without mmc and mac ..etc)
The kernel image is default to be loaded at 0x2000000 via debug port,
and the following script serves as an example:
spl()
{
cmd="riscv64-linux-gdb -q \
-ex \"target remote $host:$port\" \
-ex \"load\" \
-ex \"thread apply all set \\\$pc=&_start\" \
-ex \"thread apply all set \\\$a0=\\\$mhartid\" \
-ex \"thread apply all set \\\$a1=<dtb address>\" \
-ex \"restore u-boot.itb binary 0x200000\" \
-ex \"restore Image binary 0x2000000\" \
-ex \"c\" \
spl/u-boot-spl
"
echo $cmd
eval $cmd
}
The address where the kernel is loaded can be altered by
changing the value of KERNEL_IMAGE_ADDR.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Enable DWC IP clock in driver probe, so the MII access is possible even
outside of active network transfers. This is particularly useful when
using 'mii' or 'mdio' commands to explore PHY state, neither of which
works with DWMAC currently due to the disabled clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The gpio_request_by_name() returns zero in case of success, however the
conditional return value check in gpio_request_by_name() checks only for
(ret != -ENOENT) and if the condition is true, returns ret outright.
This leads to a situation where successful gpio_request_by_name() return
leads to immediate successful eth_phy_of_to_plat() return as well, and
to skipped parsing of "reset-assert-us" and "reset-deassert-us", so the
PHY driver operates with valid reset GPIO, but with assert/deassert times
set to default, which is 0, instead of the values from DT. This breaks
PHY reset.
Fix this by checking if return value is non-zero and then for this one
single allowed non-zero return value, -ENOENT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Load NetXtreme firmware in board_init when BNXT_ETH is selected.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
It turns out that in custom designs if the system is reset
multiple times in conjunction with a slight increase in external
temperature, the felix switch starts to behave in a strange way:
packets are no longer received on the ENECT interface connected
to the L2switch internal port (the TX side of internal port stops working
or the packets do not reach there. It is not very clear where
the packets remain blocked. None of the counters points to a disruption
in the L2switch)
The issue is not reproducible on NXP reference designs.
It was observed that by adding the switch core reset, the problem
goes aways, even if intensive testing in temperature chambers
is applied.
The current patch performs soft reset on the switch core to ensure proper
operation of the L2switch.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
socat is a very powerful tool to work with socets (and not only)
in UNIX systems. Let's add support for it in netconsole.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When, for various reasons, a bad FIT image is used where a loadable
image is marked as 0 length, attempt is made for a 0 length allocation and
read of 0 byte read operation.
Instead provide warning in log and skip attempting to do such a load.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Add a message on probe in driver model core when the default
pinctrl selection failed.
This message is displayed only when the pinctrl API is
implemented, i.e. when result is not ENOSYS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the return value ENOSYS for unsupported API
- pinctrl_generic_set_state
- pinctrl_select_state
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The helper macro CONFIG_IS_ENABLED and CONFIG_VAL are not real
configurations and they are no more present in u-boot.cfg so they can
be removed in config_whitelist.txt.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Simon Glass <sjg@chromium.org>
The two helpers macros CONFIG_IS_ENABLED and CONFIG_VAL are defined in
include/linux/kconfig.h but they are not real configurations; they can
be safely removed in the generated configuration file "u-boot.cfg".
This patch simplifies the comparison of this U-Boot configuration file.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Simon Glass <sjg@chromium.org>
- Finish converting CONFIG_USE_BOOTCOMMAND, CONFIG_BOOTCOMMAND,
CONFIG_RAMBOOTCOMMAND, CONFIG_NFSBOOTCOMMAND, all of
CONFIG_SYS_[BO]R[0-7]_PRELIM, CONFIG_FSL_DDR_BIST and
CONFIG_FSL_DDR_INTERACTIVE.
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_USE_BOOTCOMMAND
CONFIG_BOOTCOMMAND
CONFIG_RAMBOOTCOMMAND
CONFIG_NFSBOOTCOMMAND
Signed-off-by: Tom Rini <trini@konsulko.com>
- remove CONFIG_STM32_IPCC from stm32mp15 defconfigs
- enable simple framebuffer node for splashscreen for stm32mp1
- use lower-case hex for address for stm32 MCU and MPU's device tree
- define LOG_CATEGORY for stmfx pinctrl driver
- add support for probing bus voltage level translator
- add custom PHY reset bindings on AV96
- enable KSZ90x1 PHY driver on DHCOR
- stm32mp1 DDR update:
- add DDR read data eye training
- remove DDR calibration result
- remove DDR tuning support
- compute DDR size from DDRCTL registers
- DHSOM boards:
- increase USB power-good delay
- add update_sf script to install U-Boot into SF
- increase PHY auto-negotiation timeout to 20 seconds
- fix SoM and board coding strap GPIO handling
- auto-detect uSD level translator
-----BEGIN PGP SIGNATURE-----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=EHmo
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211130' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- add nor1 device support for DFU command
- remove CONFIG_STM32_IPCC from stm32mp15 defconfigs
- enable simple framebuffer node for splashscreen for stm32mp1
- use lower-case hex for address for stm32 MCU and MPU's device tree
- define LOG_CATEGORY for stmfx pinctrl driver
- add support for probing bus voltage level translator
- add custom PHY reset bindings on AV96
- enable KSZ90x1 PHY driver on DHCOR
- stm32mp1 DDR update:
- add DDR read data eye training
- remove DDR calibration result
- remove DDR tuning support
- compute DDR size from DDRCTL registers
- DHSOM boards:
- increase USB power-good delay
- add update_sf script to install U-Boot into SF
- increase PHY auto-negotiation timeout to 20 seconds
- fix SoM and board coding strap GPIO handling
- auto-detect uSD level translator
Add support of mtd backend for nor1 when this device is present on the
board, on STM32MP157C-EV1 for example, as the support of several MTD
spi-nor instance are now supported with commit b7f060565e ("mtd:
spi-nor: allow registering multiple MTDs when DM is enabled").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since the commit f42045b2e7 ("stm32mp15: replace CONFIG_TFABOOT when
it is possible") the function stm32mp1_ddr_setup is always called so the
__maybe_unused can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Compute the DDR size from DDR controller register (mstr and addrmap)
in U-Boot proper as the DDR information are useful only for SPL
but not for U-Boot proper, for example with TFABOOT.
This patch simplify U-Boot DT when several DDR size are supported
and support of next SOC in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The IPCC mailbox is only used for communication with M4 firmware but
it is not used in the stm32 remoteproc driver; it was planed but the
support of this mailbox in remoteproc for STM32MP15x is dropped.
So the associated drivers and config CONFIG_STM32_IPCC can be
deactivated to reduce the U-Boot size; the CONFIG_DM_MAILBOX can be
also deactivated as the mailbox UCLASS is no more used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable an existing simple framebuffer node in the Linux kernel device
tree and the add the associated reserved memory node to preserved the
resources (clock, memory) used by the stm32 video driver to display
the splashscreen = background in exlinux.conf file.
These resources will be released by the Linux driver only when the
associated driver is ready to avoid transition issues during the Linux
kernel initialization between U-Boot splash screen and the final display.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the framebuffer size on MMU_SECTION_SIZE in kernel, = max 2MB for
LPAE for armV7, to avoid issue with the simple frame buffer activation,
when U-Boot add a reserved memory in the kernel device tree to preserve
the splash screen until Linux driver initialization.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a new function to activate an existing simple frame buffer node
and add the associated reserved memory, with no-map properties.
This device tree update is only done when the video device is active
and the video buffer is used.
This patch uses '#if CONFIG_IS_ENABLED(DM_VIDEO)' because
gd->video_bottom and gd->video_top are only defined when CONFIG_DM_VIDEO
is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Rename the function named lcd_dt_simplefb* to fdt_simplefb* to be aligned
with the associated file name fdt_simplefb.h/fdt_simplefb.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Rename the file lcd_simplefb.c to fdt_simplefb.c to be aligned
with the configuration name and with the associated include file
./include/fdt_simplefb.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the following to Kconfig:
CONFIG_LCD_DT_SIMPLEFB
This patch also renames this config to CONFIG_FDT_SIMPLEFB as the code in
common/lcd_simplefb.c support CONFIG_LCD and CONFIG_VIDEO.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Remove the DDR interactive command tuning, as the support of a predefined
DDR PHY tuning is removed for STM32MP1 driver in SPL and in TF-A
and the result of this tuning will be never used.
Moreover this SW tuning procedure can failed on some hardware
configuration (to many BIST errors and no convergence); it will be no
more supported in the next delivery of the DDR utilities included in
the CubeMX tool of STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the read data eye training = training for optimal read valid placement
(RVTRN) when the built-in calibration is executed for LPDDR2 and LPDDR3.
This training is supported on the PUBL integrated in the STM32MP15x
DDR subsystem and it is not required for DDR3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The uSD level translator on DHSOM and Avenger96 are optional, however it
is possible to auto-detect it. This is done by setting SD CMD line high,
and then testing whether signal level on CK line matches the signal level
on CKIN line. If so, the uSD level translator is present, otherwise it is
not populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
The translator test sets CMD high to avoid interfering with a card, and
then verifies whether signal set on CK is detected on CKIN. If the signal
is detected, translator is present, otherwise the CKIN feedback clock are
disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
Enable KSZ9x01 PHY driver in DHCOR common configuration, since the
AV96 board has this PHY populated on the PCB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
