Commit graph

118 commits

Author SHA1 Message Date
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
7f5eef93af arm: Remove OMAP2420H4 and all omap24xx support
The omap2420H4 was the only mainline omap24xx board.  Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time.  Remove this board as there's not been interest in
it in U-Boot for quite a long time.

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-10 08:43:19 -04:00
Albert ARIBAUD
3da0e5750b arm: factorize relocate_code routine
Replace all relocate_code routines from ARM start.S files
with a single instance in file arch/arm/lib/relocate.S.
For PXA, this requires moving the dcache unlocking code
from within relocate_code into c_runtime_cpu_setup.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:24:38 +02:00
Albert ARIBAUD
fa6c7413d1 arm: do not compile relocate_code() for SPL builds
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Simon Glass <sjg@chromium.org>
2013-05-30 20:24:07 +02:00
Benoît Thébaudeau
e2003c16c0 imx: mx35: Remove legacy iomux support
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-05-05 17:55:04 +02:00
Philip Paeps
04f79536c3 mx35 iomux: correct offsets of IOMUX registers
This makes mxc_iomux_set_input() work correctly.  Previously, the
incorrect offset of IOMUXSW_INPUT_CTL caused mxc_iomux_set_input()
to write to the wrong register, possibly resulting in unexpected
behaviour.

Signed-off-by: Philip Paeps <philip@paeps.cx>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-04-16 18:58:47 +02:00
Tetsuyuki Kobayashi
4411b2aea7 BUGFIX: arm: data abort in get_bad_stack_swi
When swi instruction is executed, it is expected to get message
"software interrupt" in console and dump registers and reboot, as
do_software_interrupt() in arch/arm/lib/interrupts.c.
But, actually it causes data abort accessing wrong address in get_bad_stack_swi
macro in arch/arm/cpu/v7/start.S.
This patch fixes this problem.

The same mistake in arch/arm/cpu/{arm1136,arm1176,pxa}/start.S.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
2013-04-13 11:12:46 +02:00
Benoît Thébaudeau
1a9a91dcfa arm: Make all linker scripts compatible with per-symbol sections
Let all ARM linker scripts handle properly -ffunction-sections
and -fdata-sections. This will be useful for future changes in order to create
symbol-specific sections in common .S files.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:09 +02:00
Benoît Thébaudeau
5c6db120fc arm: Remove unused relocate_code() parameters
Commit e05e5de7fa made the 2 1st parameters of
ARM's relocate_code() useless since it moved the code handling them to crt0.S.
So, drop these parameters.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:07 +02:00
Benoît Thébaudeau
8b7cd098dd imx: Fix automatic make targets for imx images
Automatically build the 'u-boot.imx' (i.e. imx header + u-boot.bin) and 'SPL'
(i.e. imx header + u-boot-spl.bin) make targets for all imx processors
supporting this header, so for arm926ejs, arm1136 and armv7. Some combinations
were missing.

At the same time, fix the build of SPL targets not supporting the imx header on
arm1136. For arm1136, the 'SPL' make target was forced to build in all cases if
CONFIG_SPL_BUILD was defined, even for non-imx platforms or imx setups without
an imx header.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:06 +02:00
Benoît Thébaudeau
7086e91b0e arm: relocate_code(): Use __image_copy_end for end of relocation
Use __image_copy_end instead of __bss_start for the end of the image to
relocate. This is the same as commit 033ca72, but applied to all ARM start.S.

This is a more appropriate symbol naming for an image copy & relocate feature,
and this also saves a useless copy of data put between __image_copy_end and
__bss_start in linker scripts (e.g. relocation information, or MMU
initialization tables used only before jumping to the relocated image).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:05 +02:00
Benoît Thébaudeau
4b3db1cd31 arm: relocate_code(): Remove useless relocation offset computation
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:05 +02:00
Benoît Thébaudeau
1dd1276fd8 arm1136: Remove redundant relocate_code() return
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:05 +02:00
Benoît Thébaudeau
959eaa74b8 arm: relocate_code() is no longer noreturn
Commit e05e5de7fa made ARM's relocate_code()
return to its caller, but it did not update its declaration accordingly.

Fixing this function declaration fixes dropped C code following calls to
relocate_code().

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-04-12 07:55:05 +02:00
Benoît Thébaudeau
508611bcb7 arm: start.S: Fix _TEXT_BASE for SPL
_TEXT_BASE must be set to CONFIG_SPL_TEXT_BASE for generic SPL, and to
CONFIG_SYS_TEXT_BASE for non-SPL builds.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-12 07:55:05 +02:00
Hunter, Jon
d1da76e9f8 omap2420-h4: Fix get_timer() and CONFIG_SYS_HZ
The function get_timer() should return time in ms and CONFIG_SYS_HZ
should be set to 1000 by default. Fix both of these items.

Signed-off-by: Jon Hunter <jon-hunter@ti.com>
2013-04-08 11:29:05 -04:00
Tom Rini
0ce033d258 Merge branch 'master' of git://git.denx.de/u-boot-arm
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end.  We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.

Conflicts:
	arch/arm/cpu/ixp/u-boot.lds
	arch/arm/cpu/u-boot.lds
	arch/arm/lib/Makefile
	board/actux1/u-boot.lds
	board/actux2/u-boot.lds
	board/actux3/u-boot.lds
	board/dvlhost/u-boot.lds
	board/freescale/mx31ads/u-boot.lds
	doc/README.scrapyard
	include/configs/tegra-common.h

Build tested for all of ARM and run-time tested on am335x_evm.

Signed-off-by: Tom Rini <trini@ti.com>
2013-03-18 14:37:18 -04:00
Simon Glass
3929fb0a14 Replace __bss_end__ with __bss_end
Note this is a tree-wide change affecting multiple architectures.

At present we use __bss_start, but mostly __bss_end__. This seems
inconsistent and in a number of places __bss_end is used instead.

Change to use __bss_end for the BSS end symbol throughout U-Boot. This
makes it possible to use the asm-generic/sections.h file on all
archs.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-03-15 16:13:54 -04:00
Enric Balletbo i Serra
66c7f39923 SPL: ONENAND: Fix some ONENAND related defines.
Some ONENAND related defines use the term ONE_NAND instead of
ONENAND, as the technology name is ONENAND this patch replaces
all these defines.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-03-08 16:41:14 -05:00
Simon Glass
e9adeca3fc ppc: arm: Move sdhc_clk into arch_global_data
This is used by both powerpc and arm, but I think it still qualifies as
architecture-specific.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-04 09:05:44 -05:00
Simon Glass
582601da2f arm: Move lastinc to arch_global_data
Move this field into arch_global_data and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01 15:07:50 -05:00
Simon Glass
66ee692347 arm: Move tbl to arch_global_data
Move this field into arch_global_data and tidy up.

Signed-off-by: Simon Glass <sjg@chromium.org>
2013-02-01 15:07:50 -05:00
Albert ARIBAUD
a17617d655 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2013-01-14 17:00:02 +01:00
Troy Kisky
abbab70363 mx31/mx35/mx51/mx53/mx6: add watchdog
Use a common watchdog driver for all these cpus.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-01-13 11:39:57 +01:00
Albert ARIBAUD
e05e5de7fa arm: move C runtime setup code in crt0.S
Move all the C runtime setup code from every start.S
in arch/arm into arch/arm/lib/crt0.S. This covers
the code sequence from setting up the initial stack
to calling into board_init_r().

Also, rewrite the C runtime setup and make functions
board_init_*() and relocate_code() behave according to
normal C semantics (no jumping across the C stack any
more, etc).

Some SPL targets had to be touched because they use
start.S explicitly or for some reason; the relevant
maintainers and custodians are cc:ed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2013-01-08 22:14:50 +01:00
Benoît Thébaudeau
ccfa398547 arm1136: Fix enable_caches()
enable_caches() did not enable icache if CONFIG_SYS_ICACHE_OFF was not defined
but CONFIG_SYS_DCACHE_OFF was.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
2012-11-10 12:28:22 +01:00
Stefano Babic
d81b27a245 MX35: add support for woodburn board
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.

The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash

In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Stefano Babic
a3cbc3969d ARM: Add SPL target to arm1136
The patch adds SPL for the arm1136 architecture and
inserts SPL (the produced binary) to clobber target
in the main Makefile.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:59 +02:00
Stefano Babic
d41924a2c1 MX35: Add soc_boot_mode and soc_boot_device to MX35
The functions are required to use the generic
SPL Framework.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:58 +02:00
Stefano Babic
b736e4b929 ARM: Fix start.S when used with SPL in arm1136
This patch modifies start.S for the arm1136 to make it
conform to start.S  in armv7 architecture, to make it
usable if the SPL framework is used.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-10-26 16:27:58 +02:00
Benoît Thébaudeau
6e3dc12754 mx35: Fix eSDHC clocks
Each eSDHC instance has a dedicated clock.

gd->sdhc_clk must also be set accordingly. This is good for the case only a
single SDHC instance is used (initialization made with fsl_esdhc_mmc_init()). A
future patch will fix the multi-instance use case (initialization made directly
with fsl_esdhc_initialize()).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
2012-10-16 12:35:10 +02:00
Benoît Thébaudeau
b809b3ac13 mx35: Define MAX and AIPS registers
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:14 -07:00
Matthias Weisser
e7bed5c2b3 imx: Use MXC_I2C_CLK in imx i2c driver
i2c didn't work on imx25 due to missing MXC_IPG_PERCLK. Now using
MXC_I2C_CLK on all imx systems using i2c.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-10-15 11:54:10 -07:00
Zhong Hongbo
76abfa5781 arm: Fixed the offset for the no relocation.
When the u-boot address of destination equal to  __start,
no relocation. relocation offset(r9) = 0.

Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Tested-by: Stefano Babic <sbabic@denx.de>
2012-10-04 16:41:15 +02:00
Benoît Thébaudeau
0dc7b82e4e mx31: Define default SoC input clock frequencies
Define default SoC input clock frequencies for i.MX31 in order to get rid of
duplicated definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>
2012-09-06 14:23:30 +02:00
Benoît Thébaudeau
697191d57f Fix mx31_decode_pll
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-06 11:07:52 +02:00
Benoît Thébaudeau
543d247935 mx35 timer: Switch to 32-kHz source
Switch the mx35 timer driver to the 32-kHz clock source to avoid calling
mxc_get_clock() again and again, and to be consistent with the timer drivers of
other i.MX SoCs.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-06 11:05:24 +02:00
Benoît Thébaudeau
9c6c5c0676 mx35: Define default SoC input clock frequencies
Define default SoC input clock frequencies for i.MX35 in order to get rid of
duplicated definitions.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-06 11:05:17 +02:00
Benoît Thébaudeau
82e1b543b5 mx35: Fix clock dividers
The clock dividers that were used do not match at all the reference manual. They
were either completely broken, or came from an early silicon revision
incompatible with the current one.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-06 11:05:01 +02:00
Benoît Thébaudeau
e761955417 mx35: Fix decode_pll
The MFN bit-field of the PLL registers represents a signed value. See the
reference manual.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-06 11:04:41 +02:00
Benoît Thébaudeau
7c80326d34 mx35: Move clock enums to clock.h
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:28 +02:00
Benoît Thébaudeau
e23ee5674a mx35 iomux: Remove unused macro
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:27 +02:00
Benoît Thébaudeau
09bc3d04d9 mx35: Add cpu_mmc_init()
Add cpu_mmc_init() function to make it easy to init a single eSDHC instance.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-09-01 14:58:27 +02:00
Benoît Thébaudeau
f8f09dd404 ARM1136: Fix cache range checks
bad_cache_range actually returned true if the range was OK, but it was used
according to its name, which resulted in all valid dcache range invalidate/flush
operations being dropped. Hence, most DMA transfers resulted in garbage data.

This patch renames this function according to what it does, and it fixes the
interpretation of its return value by other functions. The chosen naming is the
same as for ARM926EJ-S in order to be consistent.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-07-21 23:24:25 +02:00
Zhong Hongbo
448217d4b2 arm: Fix to mistake clean the memory space
In currently, when __bss_start is equal to __bss_end__,
The bss loop will clear all the things in memory space.

But just only when __bss_end__ greater than __bss_start__,
we do the clear bss section operation.

Signed-off-by: Zhong Hongbo <bocui107@gmail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-20 14:24:08 +02:00
Stefano Babic
fbf4a074e0 ARM1136: MX35: Make asm routines volatile in cache ops
As well as pushed for ARM926EJS, we certainly don't want
the compiler to reorganise the code for dcache flushing
Fix checkpatch warnings as well.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marex@denx.de>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
2012-04-16 14:53:59 +02:00
Anatolij Gustschin
219872c8fe ARM1136: add cache flush and invalidate operations
Since commit 5c1ad3e6f8
(net: fec_mxc: allow use with cache enabled) the FEC_MXC
driver uses flush_dcache_range() and invalidate_dcache_range()
functions. This driver is also configured for ARM1136 based
'flea3' and 'mx35pdk' boards which currently do not build
as there are no ARM1136 specific flush_dcache_range() and
invalidate_dcache_range() functions. Add various ARM1136
cache functions to fix building for 'flea3' and 'mx35pdk'.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2012-04-16 14:53:58 +02:00
Simon Glass
4a0764858b arm: Use common .lds file where possible
Each cpu directory currently has its own .lds file. This is only needed
in most cases because the start.o file is in a different subdir.

Now that we can factor out this difference, we can move most cpus over
to the common .lds file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2012-03-30 07:43:47 +02:00
Helmut Raiger
82081406a2 mx31: add "ARM11P power gating" to get_reset_cause
Add missing reset reason 7 to get_reset_cause().

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
2012-03-27 09:41:15 +02:00
Fabio Estevam
ec0919f54b mx35: generic: Let get_reset_cause be defined only when CONFIG_DISPLAY_CPUINFO is selected
get_reset_cause() function is only used inside print_cpuinfo(), so let it be
defined only when CONFIG_DISPLAY_CPUINFO is selected.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-02-27 21:19:24 +01:00