The board can boot with UEFI. With the latest changes in U-Boot's
EFI subsystem we also have support for EFI runtime variables, without
SetVariable support. We can also store the EFI variables in a file on the
ESP partition and preserve them across reboots.
The env and efidebug commands are missing in order to configure
EFI variables and the efibootmgr though. Since U-Boot's default config
enables other EFI related commands (e.g bootefi), let's add the env related
and efidebug commands and allow users to do that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable the fastboot oem command bootbus, used to configure the eMMC
boot behavior, with same format than 'mmc bootbus'
and with parameter: boot_bus_width reset_boot_bus_width boot_mode
On stm32mp1 boards the expected command is
$> fastboot oem partconf:0 0 0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the fastboot oem command partconf, used to select the correct
eMMC boot partition, with same format than 'mmc partconf'
with parameter: boot_ack boot_partition
On stm32mp1 family:
- boot_ack = 1 (Boot Acknowledge is needed by ROM code)
- boot_partition = 1 or 2 (Boot partition 1 / 2 enabled for boot)
So on EV1 board the expected commands to select boot partition 1 or 2
$> fastboot oem partconf:1 1
$> fastboot oem partconf:1 2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the fastboot oem command format and set the variable
"partitions" with default eMMC partitions list.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Jean-Philippe ROMAIN <jean-philippe.romain@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate the live DT to reduce the DT parsing time.
For example the boot time is reduced by 200ms on STM32MP157C-EV1 board
for stm32mp15_basic_defconfig (boot with SPL) or
stm32mp15_trusted_defconfig (boot with TF-A).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Activate the logging features in SPL and U-Boot
(CONFIG_LOG and CONFIG_SPL_LOG) and the command 'log' with
CONFIG_CMD_LOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate CONFIG_CMD_ELF to accept the command "bootelf".
This patch simplifies the file stm32mp defconfig, as we have
no reason to deactivate this command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate CONFIG_CMD_IMPORTENV to accept the command "env import".
This command is useful in script to include some variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
CMD_ADC selected DM_REGULATOR unconditionally without enabling DM.
That's why change select to depends on to cover it.
Kconfig is showing this issue as:
WARNING: unmet direct dependencies detected for REGMAP
Depends on [n]: DM [=n]
Selected by [y]:
- DM_REGULATOR_PBIAS [=y] && DM_REGULATOR [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update CMD_ADC=y configs to enable DM_REGULATOR now]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables the support of FMC2 EBI.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Activate the support of the command adtimg to handle android images.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save the environment at the end of the U-Boot partition, the GPT
partition named "ssbl" in SD card or eMMC and avoid requirements
on the "bootfs" file system generated via specific raw tools
(like wic and genimage).
With the previous configuration of the U-Boot environment saved in ext4
file, U-Boot need to create/modify the file uenv.txt in the ext4 file
system; so this EXT4 file system need to be generated without some
functionality, like metadata_csum and dir_index, because they are not
supported by U-Boot.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Migrate the ST Microelectronics STUSB160X Type-C controller code in
a generic I2C driver in st/common, based on Linux one in :
drivers/usb/typec/stusb160x.c
This patch simplifies the stm32mp1 board code and allows to reuse
this STUSB160X driver in other boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate the command env erase to reset the environment with the command:
> env erase
it is simpler than:
> env default -a
> env save
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As kernel v5.6 have a solution since so we will be able to enable
the watchdog at boot time. It is reloaded by the watchdog
framework (if CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is set) and
until the userspace watchdog daemon takes over control.
Need presence of kernel patch 85fdc63fe256 ("drivers: watchdog:
stm32_iwdg: set WDOG_HW_RUNNING at probe") integrated in v5.6-rc1.
This patch revert the previous commit ca351e705a ("stm32mp1:
deactivate WATCHDOG in defconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch activates the new configuration CONFIG_GPIO_HOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of errno_str, used in command pmic and regulator.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Need Realtek driver to manage in RTL8211F the configuration of the LED.
Initialize LCR (LED Control Register) to configure green LED for Link,
yellow LED for Active
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Move CONFIG_SYS_MTDPARTS_RUNTIME into Kconfig done by moveconfig.py.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable these standard U-Boot commands for image manipulation and for
starting the default boot command using 'boot' command in U-Boot shell.
Cc: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This partially reverts changes by commit 2cc393f32f
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move CONFIG_ENV_SECT_SIZE and CONFIG_ENV_OFFSET in stm32mp15_*_defconfig
for ST board with NOR support (STM32MP15xx-EV1 boards)
- CONFIG_SECT_SIZE values = the max supported NOR erase size (256KB)
- CONFIG_ENV_OFFSET = offset for NOR (ENV_IS_IN_SPI_FLASH)
This Patch prepares the U-Boot support of boards with STM32MP15x SOC
not provided by STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable support for the rng device on the stm32mp15 configs.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Rsync all defconfig files using moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Many boards do not use all selected framebuffer depth
configurations, for such boards there is some unused
code in video and console uclass routines. Make depth
specific code optional to avoid dead code and slightly
reduce binary size. Also make ANSI code optional for
the same reason. When i.e. using only VIDEO_BPP16 the
code size shrinks (below values when using gcc-7.3.0):
$ ./tools/buildman/buildman -b video-wip -sS wandboard
...
01: Merge git://git.denx.de/u-boot-sh
02: video: add guards around 16bpp/32bbp code
03: video: make BPP and ANSI configs optional
arm: (for 1/1 boards) all -776.0 bss -8.0 text -768.0
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
CONFIG_MTD must be reserved for the MTD core. Like any other
subsystem, prefix the symbol by DM when it comes to DM support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Add Kconfig files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add read for OTP and PMIC NVM with alternates
on virtual DFU device.
Serie-cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the support of SPI NAND in stm32mp1 U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of DFU for MMC, MTD, RAM and MTD command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
